Search Documents

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By Gisele Azimi, Jason Tam, Adrian Lambert

Many advanced technologies in modern society require the use of rare earth elements (REEs). Since these technologies are dominating the world, the demand for REEs is increasing fast. Finding new sources for them is highly of interest. One secondary source of REEs is phosphogypsum (PG), a by-product of the phosphate fertilizer industry. Microwave treatment is investigated as a method to enhance hydrometallurgical recovery of REEs from phosphogypsum, with results showing a 30% improvement in leaching efficiency.

Mar 1, 2017

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By Hemraj Dangi, S. Murali, Bhisham Yadav, Mohini Saxena, P. Asokan

"Demonstration studies were carried on the use of fly ash as soil modifier and supplier of micronutrients to improve the agricultural productivity based on the process optimised at lab scale at Advanced Materials & Processes Research Institute, Bhopal. The field trials were conducted in Uttar Pradesh (North India) Orissa (South Eastern India) and Madhya Pradesh (Central India) under different soil and crop conditions. 100-650 tonnes of fly ash per hectare were applied depending upon the soil and fly ash characteristics. Both short and long term studies on impact of fly ash on soil and food quality were conducted. With the fly ash application, the edible yield of tomato, cabbage, potato, wheat, pea, onion, paddy, sunflower, maize etc., were increased from 12 - 46% as compared to the control soil where no fly ash was used. The crop response to various elements mainly heavy metals grown in soil and fly ash applied soil was found comparable to that of control, which are within the permissible limits and meet the food quality standards. The results of impact of fly ash on biotic and abiotic properties of soil, along with the quantity and quality of agricultural produces generated under pilot scale demonstrations in three different parts of India are discussed in this paper. The outcome of this work could act as guiding force for confidence building and to maximise the use of fly ash, generated from thermal power plants worldwide as one of the major mineral waste for agriculture purposes.IntroductionThe advantages of application of fly ash in terms of improvement of soil properties and crop yields have been published by various researchers in India and abroad. Attention is also given about the possible negative and beneficial impact of pond ash in agriculture due to presence of heavy elements, radioactive nuclides and plant nutrients in fly ash. It is evident from the analysis of Indian fly ash that the presence of heavy elements and radionuclides levels are comparable with normal soil. The positive impact that has been reported is with regard to germination, yield and crop growth. The significant impacts are: long term effect of heavy and toxic elements content of fly ash on soil and up take of these elements by plant. Pilot scale demonstration studies have been completed with varying soil crop-combination under different agro-climatic conditions showed considerable improvement in the productivity of cereals, oil seeds and vegetables."

Jan 1, 2008

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By Dao Su, Ganghua Fu, Xuling Chen, Yufeng Guo, Min Gan, Tao Jiang, Xiaohui Fan

"The sinter quantity and quality of limonite in the magnetite and hematite sintering models were studied and compared. For the sintering of magnetite, the results showed that the increase of limonite improved the permeability of sinter mixture, increased the sinter quantity and quality. The sinter strength and productivity were decreased when the proportion of limonite exceeded 50%. The appropriate proportion of limonite was 40%-50%. For the sintering of hematite, the sinter quantity and quality were first maintained at the same level thereafter declined, more obviously when the proportion of limonite exceeded 40%. The amount of calcium ferrite increased whose shape changed from acicular to leaflike and block gradually with the proportion of limonite increased from 0% to 80%.IntroductionWith the fierce competition of domestic and overseas iron markets in the twenty-first century, cheap ores such as limonite are used to be sintering raw materials to cut the costs of sinter and pig iron for steel making, and boosts the competitiveness of steel companies [1, 2]. In addition, as the reserve volume of hematite of high grade is reducing year by year, the usage amount of limonite in sintering are expanding in major domestic and international sintering plant [3, 4]. Sintering can be divided into two types, majoring in concentrates and fine ores, according to the different types of raw materials. The sintering characteristics of limonite in the two types above have been studied and compared in this paper, which makes a significant sense for the research of limonite sintering properties and guidance of ore proportioning in sintering plants."

Jan 1, 2012

By Roger W. Lee

The commissioning of the prototype Imperial Smelting Furnace (ISF) in 1950 was a technological breakthrough in the pyrometallurgical smelting of zinc and provided significant advantages over the existing retort processes. However, for most zinc concentrates the electrolytic zinc process continued to be more economic. Therefore, the Imperial Smelting Process (ISP) specialised in smelting zinc and lead concentrates that were less amenable for treatment by either the electrolytic zinc process or the lead blast furnace. Subsequently, improved mineral processing techniques led to a decrease in the availability of these concentrates so the treatment of secondary materials in the ISP assumed greater importance. This was facilitated by the development of techniques such as hot briquetting and tuyere injection. In 2002 over 1 million tonnes of zinc and 400,000 tonnes of lead were produced by the ISP. However, in the 2002-3 the economics of the Process became extremely difficult because of low metal prices and increased operating costs. This resulted in the closure of four ISP smelters in 2003 and two in 2005. Nevertheless, two new ISP smelters are scheduled for commissioning in China in 2006 where local economic conditions continue to favour the process. The economics of the process are examined particularly in respect of smelter margin and operating costs. The need to increase the smelter margin means that the future of the process will be closely linked to its ability to consume secondary materials and an examination will be made of its potential for conversion to 100% secondary operation. Apart from a reduction in raw materials costs, a substantial reduction in operating costs would ensue from not operating sinter and sulphuric acid plants.

Jan 1, 2006

By Batric Pesic

Recovery of gold from refractory ores was studied by pressure oxidation as the method of ore pretreatment followed by bromination of oxidized residues. Three different ores were examined, Au-Ag, Au-Ag-Te, and Au-silver free ore. Pyrite was the major host mineral for gold in these ores. The effect of pressure oxidation parameters (temperature, pressure of oxygen, time, and pulp density) on subsequent bromination under standard conditions was examined. Bromination of residues produced under standard pressure oxidation conditions was examined as a function of: temperature, bromine and sodium bromide concentration, and time. Recovery of gold on activated carbon, from the pulp after bromination, was studied too. Recovery of gold from silver containing ores was lower (87-91%) than the recovery of gold from silver free gold ore (97%). In each studied case, the presence of activated carbon in the pulp further increased the recovery of gold.

Jan 1, 1992

By Oleg I. Platonov

The process for desulfurizing coke oven gas in a regenerative system ?scrubber-stripper?, with sour gas being fed to Sulfur Recovery Unit (SRU) and tail gas being recycled to raw coke gas scrubber, has been developed. A key problem of this process is the presence of elemental sulfur in the SRU off-gas, which may deposit on gas-blowing equipment, thus disrupting its operation. A new treatment technology for SRU off-gas that has been worked out for a Claus unit operated by «Russian Metallurgical Company» (RMC) in Magnitogorsk (Russia) is presented. It incorporates a catalytic hydrolysis/hydrogenation stage, where all sulfur-bearing species such as sulfur dioxide, carbonyl sulfide and elemental sulfur are converted to hydrogen sulfide. The SRU in Magnitogorsk comprises three main units: gas re-heater; catalytic hydrolysis reactor and waste gas cooler. Re-heater is required to increase temperature of the process gas up to a level of catalytic conversion (beyond 330-3500C). Oxygen utilized as an oxidizing agent reduces the volume of waste gas to a minimal possible value. The operational data garnered since 16.07.2004 clearly shows that the new technology allows high-level purification of Claus tail gas from elemental sulfur. Unlike SCOT ? process, this technology does not require separate stages for H2S removal and enrichment that tangibly simplifies its implementation at lower capital and operation expenditures.

Jan 1, 2006

By M. M. Sadawy

"The increased rate of exploitation of iron ores has resulted in a rapid depletion of high-grade iron ore deposits in Egypt. New iron reserves have to be discovered to secure the iron ore for steel production. This paper aims to study the characterization and magnetic separation of low grade Aswan iron ore. The results showed that Aswan iron ore is composed of oolitic hematite, goethite, quartz and kaolinite. The screen analysis indicated that Aswan iron ore had a uniform distribution of iron and silica in the different particle size fractions and there is no any particle size has high amount of iron or low content of silica. On the other hand the results of dry high intensity magnetic separation illustrated that this technique is not suitable for upgrading this ore.IntroductionIron is one of the common metals used in industry, as well as being the fundamental raw material used in iron-steel industry; products are wide spread even in daily uses. The total iron ore reserves of the world have been estimated as 3 70 billion tones; 160 billion tones is classified as economical, while 210 billion tones as potentially economical [1]. An estimated 98% of the iron ore exploited in the world is used in the manufacture of pig iron and steel, which are non-substitutable backbones of modem society. The rapid increase of world steel production over the last few years have required an equal increase in iron ore production, from 876.8 Mt in 2006 to 948.1 Mt in 2007 [2]. The increased rate of exploitation of iron ores has resulted in a rapid depletion of known high-grade iron ore deposits. This, in turn, has led to a dramatic increase of prices. In the absence of any major new discoveries of high-grade iron ore deposits, mining companies have turned to lower-grade materials to assess their beneficiation potential to expand their production base and beneficiation capacity, in order to satisfy future demand. Egypt is going to face shortage in iron production, consequently new iron reserves have to be discovered to secure the iron needed for the country [3]. Exploitation of low grade ores requires special equipments and techniques for recovery of minerals values. High gradient magnetic separators offer promise and great potential of application both technologically and economically in the processing of fine particles containing weakly or feebly paramagnetic components [4-6]. Within this existing framework, this research was initiated to assess the beneficiation potential of low-grade Aswan iron ore by high intensity magnetic separation."

Jan 1, 2013

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By D. Tait, M. A. Halim, V. I. Lakshmanan, R. Sridhar

Rare earth elements (REEs), nickel and cobalt find their use in developing strategic materials and their demand is consistently increasing in the world while the extractable ores of these metals are gradually depleting. Process Research ORTECH Inc. (PRO) has developed innovative mixed chloride leaching processes for the recovery of REEs from alumino-silicate ores, and nickel and cobalt from laterite ores. The addition of magnesium chloride in hydrochloric acid enhances the activity of the hydrogen ion by orders of magnitude, which permit rapid leaching rates at moderate temperature and atmospheric pressure, along with high metal recovery. Innovative solvent extraction process steps are used for the separation of these metals from pregnant leach solutions. PRO’s processes also produce value added by-product of high purity iron oxide and recycle chloride lixiviant to the leaching stage. This paper describes the leaching and separation reaction mechanisms and potential process flowsheets.

Mar 1, 2017

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By Miguel Barron

Recently, a new lance design for BOF steelmaking has been proposed in the literature. This lance, in addition to six peripheral inclined supersonic nozzles, contains a vertical centered nozzle whose oxygen flow is independent from the main oxygen supply. The above authors affirm that their lance maximizes the droplet generation without causing spitting. In this work, the performance of a lance with four peripheral nozzles and one vertical centered nozzle is numerically modeled by means of Computational Fluid Dynamics software. Transient two dimensional computer simulations were carried out considering two phases, namely molten steel and gaseous oxygen. Numerical results confirm that bath agitation and droplet generation are enhanced as a result of the vertical centered nozzle, however a proper performance of this lance, related to a conventional one, strongly depends on the Mach number of the oxygen jets and the lance height.

Jan 1, 2008

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By V. V. Geikhman

The paper updates the Plant experience in the development and implementation of an advanced environmentally friendly zinc production technology complying with the technological and economic level of producers in the world and the standards of maximum permissible gas emissions stipulated by the Russian legislation. General water recycling engineering allowed to ensure 95.6% water rotation level. All solid wastes formed during treating zinc concentrate are processed into marketable products or semiproducts and sold. As a result of implementing innovation techniques production at the Chelyabinsk Zinc Plant is non-waste.

Jan 1, 2006

By R. J. Batterham

This paper sets the scene for the Australian-Asian Pacific Course and Conference on Pyrometallurgy for complex materials and wastes. The relentless presence of competitiveness is rehearsed as the source of the current trends towards continuous improvement and benchmarking. While this might be expected to lead to more spending on pyrometallurgy, the opposite appears to be the case. The paper examines the reasons and suggests that we face an increasing challenge for selective developments that can lead to sustainable competitive advantage - both in mineral and in waste processing.

Jan 1, 1994