Search Documents

By G. A. Brooks

The problem of treating concentrates with increasingly higher levels of arsenic and antimony is compounded by the trend to stricter environmental guidelines regarding the disposal of smelter wastes. Much of the arsenic and antimony from non-ferrous processes is recovered as oxide fume. The options for handling these fumes include recycling them to the smelter, stabilising and disposing of them, and recovering values from them. Whilst arsenic oxide has little value, there is a market for antimony oxide and this provides an incentive for devising techniques for separating antimony oxide from arsenic oxide before disposal of the arsenic oxide. Arsenic can be separated from antimony oxide by selectively volatilising the more volatile arsenic trioxide from a mixed oxide sample or by selectively condensing the less volatile antimony tetroxide at high temperatures, leaving arsenic trioxide to condense out at lower temperatures. The results of selective volatilisation experiments at 379 to 587 °C indicate that it is difficult to achieve an arsenic content below 5.0 wt.% using air or nitrogen as carrier gas due to the formation of solid solutions between the two oxides. Injection of oxygen into a mixed vapor stream improved separation by selective condensation and antimony tetroxide containing as low as 0.23 wt.% was obtained in laboratory experiments.

Jan 1, 1994

By Rodney L. Williamson

Optimal estimation theory has been applied to the problem of estimating process variables during vacuum arc remelting (V AR), a process widely used in the specialty metals industry to cast large ingots of segregation sensitive and/or reactive metal alloys. Four state variables were used to develop a simple state-space model of the V AR process: electrode gap (G), electrode mass (M), electrode position (X) and electrode melting rate (R). The optimal estimator consists of a Kalman filter that incorporates the model and uses electrode feed rate and measurement based estimates of G, M and X to produce optimal estimates of all four state variables. Simulations show that the filter provides estimates that have error variances between one and three orders-of-magnitude less than estimates based solely on measurements. Examples are presented that verify this for electrode gap, an extremely important control parameter for the process.

Jan 1, 2001

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By Y. Z. Zhang

Cyanide has generated environmental concerns because of its toxicity, and it may not respond to the treatment of complex and refractory gold ores. Gold leaching by thiourea is one of the most promising substitutes of cyanide. However, the high reagent consumption has hindered thiourea from its commercial application in gold extraction. The process chemistry and mechanism of thiourea degradation has been discussed on the basis of chemical bonding theory, thermodynamics and electrochemistry in this paper. Progresses on the decreasing of thiourea consumption have been summarised. The potential application of thiourea in gold extraction has been evaluated.

Jan 1, 1996

By J. Peter, S. E. James, J. L. Watson

A survey of operating zinc smelters and refineries throughout the world has been done in conjunction with the Lead-Zinc 2000 Symposium. This survey follows the examples set by the Japanese Mining Industry Association in 1985 and 1995. Questionnaires were sent to operating zinc plants that covered feed materials, process details, energy consumption and labor requirements. The voluntary responses to the survey were tabulated. Key operating parameters including feed grade, production capacity, quality of the intermediate products and quality of the final products have been compared for both hydrometallurgical and pyrometallurgical processes.

Jan 1, 2000

By Guo Xueyi

The morphological characteristics of the nickel particles electrodeposited from chloride dominant aqueous solution was investigated. The effects of the electrolyte constituents, the parameters for the electro-deposition on the morphology of the nickel particles were addressed. It is evidenced that not only the particle size but also the morphology of the deposited nickel particles strongly depend on the electrolyte constituents and technical operation conditions. The electro-crystallization mechanism of the metallic nickel particles deposited at high current density was elucidated. The ultra-fine nickel particles with flake, nodular or dendrite shape may be produced by controlling the duration for electro-deposition.

Jan 1, 2003

By Richard Hollis

The Mount Isa copper smelter was expanded in 1998 to a capacity of over 250000 t/y anode copper. This tonnage will be produced from a single stream consisting of an Isasmelt smelting furnace, and four Peirce-Smith converters - one of which was installed as part of the expansion project. During the course of the expansion project Mount Isa Mines Limited (MIM) signed an agreement with WMC Fertilizers Ltd (WMCF) to supply sulphur containing smelter gases over the fence to a new sulphuric acid plant to be built by WMCF. This will result in a further increase in copper production by reducing the time when smelting is curtailed by Air Quality Control restrictions. As well as the need to modify the primary gas system to connect to the acid plant, the hoods and crossover ducts and their support structures on the original three converters required replacement, and secondary ventilation was also needed to improve converter aisle hygiene. Each of these areas was addressed by the project. Preliminary ideas for carrying out the modifications were found to have a serious impact on converter aisle operations, and would have led to a production loss of over 50000 tonnes of copper. Following benchmarking in other copper smelters, a suitable construction plan was developed and carried out to minimise this loss. This paper describes the methodology and construction plan adopted.

Jan 1, 1999

By Luiz A. Teixeira

This paper reports the results of kinetic studies involving the precipitation of arsenic from aqueous solutions as FeAs041 Fe(OH)3' using FeS04 as source of Fe ions, and Air or H202 as oxidizing agents. Both systems lead to an efficient removal of arsenic. The differences in oxidants performances are in the precipitation reaction rate -much faster using hydrogen peroxide. Mechanisms of reactions were suggested based on the following main steps:

Jan 1, 1996

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Z. Sadowski

The influence of organic acids simple salts and A. niger saccharose and molasses worts on sodium oleate adsorption on the salt-type mineral surfaces has been studied. It was found that salts of organic acids had an effect on the sodium oleate adsorption on barite calcite and magnesite. The collector adsorption on the barite and calcite surfaces decreased under the influence of investigated worts. Experimental data suggest that the biomodification of salt-type mineral surfaces can be used for the selective separation of these minerals.

Jan 1, 1991

By Courtney A. Young

All cyanide species are considered toxic and can be found predominantly in industrial effluents generated by metallurgical operations. For example, cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent water contamination. Various methods of cyanide remediation by separation and destruction are available, but certain methods are more effective than others depending on the cyanide species being remediated. Photolytic destruction is regarded as the one technique that is independent of the cyanide species involved. The destruction of various cyanide species by several photolytic techniques has been investigated for the past few years. A literature survey suggests heterogeneous photocatalysis with anatase (TiO,) should behave similarly to homogeneous photolysis with hydrogen peroxide (H,O,) since proposed reaction mechanisms for both processes involve hydroxyl radicals. However, experimental evidence on a suite of cyanide species suggests otherwise. A new mechanism for the photocatalytic destruction of cyanides, especially SAD species, is therefore proposed.

Jan 1, 1998

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By John R. Turney

The success of the Mclaughlin acid pressure oxidatiun process has proved that a complex hydrometallurgical process can be an economically viable means of treating refractory gold ores. Homestake's Mclaughin acid pressure oxidation process was commissioned in August 1985 and ts currently operating at design tonnage of 3,000 tons per day. Mineralogical and process studies on the operating plant are discussed to show the improved understanding: of the process and its future applications. These studies are also compared with the initial process development work, thus illustrating the success of the initial scale up considerations.

Jan 1, 1989

By Osamu Iida

Since 'start-up of the larger Mitsubishi Continuous Copper Smelting Process in 1991, furnace relining campaign was gradually prolonged to once every 2 years according to deregulation of governmental boiler inspection. On the other hand, in 1998 Naoshima smelter embarked on an intermediate strategic expansion plan to strengthell its international competitiveness. As part of this plan, modifications were implemented in the copper smelter designed to increase output of anodes from new charge source to 270,000 tpa. In May 1998, treatment of dried neutralized residue was started in C furnace, and during the shutdown for brick relining in April 1999, intensive modifications to the boilers as well as the installation of new spray coolers for furnace off gas treatment were implemented. Finally, the new larger oxygen plant was commenced its operation in May 2000 and the expansion was achieved around 30% increase of anode production from original design.

Jan 1, 2001