Search Documents

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009

By Mansoor Barati, Yindong Yang, Yonggang Wei, Bo Li, Alexander McLean

Reduction roasting followed by magnetic separation is an important method for treating laterite nickel ores. In this work, garnierite type laterite ore from Yunnan province in China was reduced by methane under different conditions followed by magnetic separation to obtain the ferronickel concentrate. The phase and microstructure transformations of garnierite in the reduction process were investigated using XRD and SEM-EDS. The experimental results showed that reduction temperature from 873 to 1173 K had only a small effect on content and recovery of nickel and iron. The content and recovery of nickel and iron in the concentrates increased slightly with prolonging reduction time. In addition, the nickel and iron content decreased with increasing methane concentration, but the recovery of nickel and iron increases. A decrease in the iron content and recovery were observed when the dosage of sodium sulfate varied from 5 to 20% at a temperature of 1073 K and reducing time of 90 min, while the nickel content and recovery gradually increased.

Mar 1, 2018

By Von L. Richards

Rapid Freeze Prototyping (RFP) is a novel solid freeform fabrication technology that creates parts by depositing water droplets and freezing them rapidly to form layers. An investigation into the smallest thickness that can be achieved by the RFP process was conducted. The factors that could significantly affect the thickness of the part built by this process including substrate temperature, volumetric feed rate, table velocity, nozzle frequency, nozzle standoff distance, and head pressure were considered. A shell building technique for use with the RFP system has been developed. Thin wall ice patterns have been invested using production shell building techniques and an alcohol-based slurry. The finished shells were quantitatively evaluated by inspecting their total shell thickness, mold cavity dimensional reproducibility, and shell strength. Pattern loss is influenced by not only the alcohol / water interaction but also the starting thickness as it relates to thermal mass.

Jan 1, 2008

By Chao Li, Hongxu Li, Yang. Xie, Meng Wang, Xiangxin Hao

"With the development and utilization of resources of gold, high quality gold mine resources gradually exhausted, and refractory gold ore has become the main raw material for gold smelting, while the smelting pollutants impacting on the ecological environment is growing, in recent years there have appeared several methods of green extraction of gold such as bio-oxidation. In this paper, the life cycle assessment models about three different gold extraction technologies have been put forward. Material consumption, energy consumption and emissions during each gold production process are analyzed by using GaBi 6 software, and the environmental impact of each process is also evaluated by means of CML2001 methodology. Calculation and analysis results show that the energy consumption and material consumption are the main factors causing the environmental load; and the environmental impacts of the production process mainly attribute to the category of greenhouse effect, resources consumption and environmental acidification. Based on the evaluation, some optimization tips are proposed.IntroductionOver the past decades, as the industry policy environment continues to improve as well as gold exploration and mining smelting capacity continues increasing, gold production shows a prospecting tendency. With the wide use of gold, the demand for gold is growing, while easy smelting gold mine resources become exhausted and refractory gold ore has become the main raw material for gold smelting. In addition, pollutants impact on the ecological environment is also growing year after year.LCA (Life Cycle Assessment) makes evaluation of product “from cradle to grave” as its whole process, up to finding the sources of environmental impacts and solutions, to comprehensively account the use of resources and lower emissions. In the industrial field, life cycle can compare different technologies from different aspects of resource use, energy consumption and environmental emissions [1]. In recent years, using LCA to evaluate metallurgical industry process also has more development. The paper mainly uses LCA and scenario analysis for the gold metallurgical process by GaBi 6, to investigate the environmental impact of three different technologies of gold extraction metallurgical process. The established three evaluation models include the hydrometallurgical, pyro-metallurgical processes and bio-oxidation pretreatment methods respectively. Several environmental indexes would be selected to evaluate the environmental impact in order to find which process has smallest environmental load and some suggestion of reasonable way gold resource utilization."

Jan 1, 2014

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Ronne Hendrajaya

"The influence of microstructural defects on strength in Si3N4 is reviewed. The presence of cracks, pores and inclusions greatly affects the strength of Si3N4. The micron order crack size and distribution were quantified by micrographic technique. The observed defect size was range from 4 µm to 28 µm.The density of defect increases as the defect size decreases. The correlation between defects size and density was better represented on the logarithmic graph. The correlation was linier. IntroductionFracture in ceramics materials occurs from. In order to understand the relationship between strength and defects, it is necessary to examine the fracture process quantitatively.1In this study, the micrographic technique is used to determine the defects size and distribution in Si3N4. The observed data will be used to predict the material strength by using fracture mechanics rnodel.2Experimental ProcedureThe sintered Si3N4 specimens ( SNl, Japan Fine Ceramics Center) were sliced into 1mm thick . The both sides of specimen surface were polished into by using diamond slurries with particle size down to 2µm. The final thickness was 0.045 mm. The optical microscope (NIKON OPTIPHOT02-POL) was used to observed the internal defects with transmission mode. The reflection mode was used to determine the surface defects, so that the internal defect could be distinguished from surface defect. The measurement and counting was taken on the micrograph and the longest part of the defect was measured as the defect size. The size density distribution of internal defect is taken."

Jan 1, 2000

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By S. Seetharaman

The present paper presents. the concept of micro-models and illustrates the application of the same in the simulations metallurgical processes. Development of micromodels requires access to accurate thermodynamic, thermophysicaland kinetic information for the relevant systems with suitable models to extrapolate the data as functions of temperature and composition. Experimental measurements and modelling of the thermodynamic properties, sulphide capacities and viscosities of oxide melts carried out in the department are presented. The incorporation of these models in process models, with special reference to ladle refining of steel is illustrated. Typical example of micro-modelling of solid-gas reactions is also presented.

Jan 1, 1999

By Nicola Baldo, Marco Pasetto

"The paper discusses the results of a laboratory study, aimed to evaluate the suitability of the bottom ash from Municipal Solid Waste Incineration (MSWI), obtained from different Italian plants, to be recycled in the lithic skeleton of bituminous mixtures, for base layers of road and airport pavements. The research involved a preliminary study of the physical and geotechnical properties of the bottom ash by itself; it was followed by a mechanical characterization of the bituminous concretes. The traditional Marshall methodology was used to identify the optimum bitumen content; the mixtures were also mechanically checked by means of the stiffness modulus test, repeated load axial test and fatigue test. Because the requisites for acceptance in the Italian Specifications and Standards have been satisfied and given the positive mechanical performances, it has been verified that the MSWI bottom ash can be used as substitution of the lithic materials in the road bases, also with very high contents (up to 81% on the weight of the aggregate). Introduction The incineration of Municipal Solid Wastes (MSWs) provides for by-products which can be mainly classified as bottom ash and fly ash. The first one, corresponding to the 25% on the weight of the wastes to be incinerated, so resulting the principal product of the process, is mainly composed by Silica (Si), Iron (Fe), Calcium (Ca), Aluminium (Al), Sodium (Na) and Potassium (K) oxides, so presenting a composition similar to that of different natural materials. Its metallic fraction can be recovered; the remaining part is usually stocked in dumping or, less frequently, recycled. Bottom ash can be re-utilised in the construction of new infrastructures, especially in bitumen bounded mixtures, because of the inert properties of the binder which covers the grains with a subtle film, that prevents the release of heavy metals. The paper describes a study aimed to design new bituminous mixes for flexible road and airport pavements, realised with the highest content of 4 types of bottom ashes, deriving from different MSWI plants of the Northern Italy. The ashes will be named as BA1, BA2, BA3, BA4 respectively (the origin cannot be specified)."

Jan 1, 2008

By D. Holdridge, D. Liao, S. Waterfall, N. Strobl, S. Sun

High melting point inclusions, such as spinel, alumina and AlO rich calcium-aluminates, have a strong tendency to agglomerate on the tundish stopper rod and Submerged Entry Nozzle (SEN) during the steel casting process, and eventually to cause SEN clogging. Calcium treatmen by wire injection during steel refining during Ladle Metallurgy (LM) is commonly used to modify these troublesome inclusions to lower melting point inclusions. However, too much Ca injection (Ca over-treatment) can cause operational issue (e.g. slide gate plate erosion),as well as increase Ca cost. Therefore, it is desirable to add an appropriate amount of Ca to avoid either under-or over-treatment. Based on inclusion analysis with an ASPEX® computer controlled scanning electron microscope (ASPEX) instrument, AlO and AlO rich calcium-aluminates were identified as a major cause of SEN clogging at ArcelorMittal Dofasco Electric Arc Furnace (EAF) steelmaking stream. A Ca treatment index was developed to improve the inclusion modification. The improved inclusion control has reduced SEN clogging and enhanced steel quality.

Mar 1, 2017

By Daniel Kim, Ari Rantala

Efficient on-line monitoring of electrolytic cell performance in copper electro-refining has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Based on Kennecott Utah Copper's innovation Outotec has developed a novel and innovative electrolytic cell monitoring system called CellSense™ System. As the system is based on self-powering from bus bars, wireless communication, on-line adaptive modeling and easy to access information and alarming, traditional obstacles of electrolytic cell monitoring are eliminated. With cell voltage and electrolyte temperature measurements, CellSense System enables real-time cell performance discovery and early reaction to critical production or quality disturbances such as short-circuiting, flow blockages, cold cathodes or electrolyte temperature excursions. During the past few years the system has been delivered to over 3500 commercial cells. In this paper the largest CellSense™ System ever delivered and recently adapted by Kennecott Utah Copper with 1412 cells monitored on-line for high tankhouse performance, cathode quality and optimized operator work flow is presented. Early results and benefits are discussed.

Jan 1, 2012

By Mizraim Uriel Flores, Elia Guadalupe Palacios, Sayra Ordoñez, Iván Alejandro Reyes, Ister Mireles, Martín Reyes, Francisco Patiño, Hernán Islas, Víctor Hugo Flores

This paper presents the characterization of a sample of mercury jarosite that was synthesized by slowly adding Hg(NO3)2H2O into a Fe2(SO4)3nH2O solution. X-ray diffraction (XRD) analysis performed on the sample confirmed that the compound presents a crystal phase corresponding to mercury jarosite. Analysis through Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS) determined that the precipitate is composed of mercury, sulfur, iron and oxygen. It is made up of spherical particles with an average size of 38 μm; these particles are made of rhombohedral micro-crystals with sizes ranging between 1 and 2 μm. Chemical characterization was performed through dichromatometry analysis, gravimetry and atomic absorption spectroscopy (AAS), thus obtaining the following composition: 27% Fe3+, 37% SO4 2− 14% Hg2+, 22% OH− + H3O+ + H2O. The following approximate formula of the compound was determined from chemical analysis: [Hg0.39(H3O)0.22]Fe2.71(SO4)2.17(OH)4.79 (H2O)2.09.

Mar 1, 2017

By G. Riverin, C. Simard, W. D. Stevens

"An on-line technique to measure the efficiency of decoating I delacquering processes is being developed by Alcan' s Arvida R & D Centre. Decoating processes are used to remove moisture and coatings from shredded coated material such as Used Beverage Containers (UBC) before melting. Complete removal has been demonstrated to maximize metal recovery. Quantifying the weight of carbon and organic residue adhering to the shred surfaces is very difficult to measure directly, as the material can be highly folded. The technique developed indirectly measures the residue remaining by analysing the concentration of CO evolved in the decoater end zone exhaust gas.A commercial CEMS (Continuous Emission Monitoring System) incorporating an infrared type CO gas analyser was modified for on-line process exhaust gas analysis. Both pilot and plant trials had demonstrated that the CO concentration measured was inversely proportional to the efficiency of the organic removal achieved. As the quality of coated purchased scrap can be highly variable in moisture and organic content, continuous measurement should permit adjusting the feed rate and other decoater process parameters to the quality of decoating required."

Jan 1, 2000

By W. K. Rankin

Achieving continued economic growth with social equity within the natural limits of the Earth's eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

Achieving continued economic growth with social equity within the natural limits of the Earth's 'eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By Dachun Liu, Baoqiang Xu, Bin Yang, Yong Deng, Heng Xiong, Xiumin Chen

"In this paper, vacuum distillation technology has been employed to study the possibility and regularity of separating copper and enriching lead, silver and other valuable metals from copper- based multi component alloys. The result of experiment indicated the practicability of vacuum distillation dealing with copper base complex multi-component alloy to separating lead and silver, when the vacuum distillation temperature was 1637K, distillation time was 60min; residual gas pressure was 20-30Pa, the removal rate of silver was 95.86%, of lead was 99.63%; the evaporation rate of copper was 0.745%. The removal rate of arsenic, antimony and tin respectively were 83.09%, 48.12% and 24.54%. Vacuum distillation method is applicable for dealing with the copper-based multi component alloys, silver and lead can realize effective recovery.IntroductionCopper generally go with lead mineral, therefore, to remove copper from lead becomes an inevitable link in lead smelting. Dross from removed copper usually contains lead, arsenic, antimony, tin and noble metal silver. In abroad, soda ash-iron dust is adopted to process copper dross of this kind. The outcomes of this process are lead matte, wet lead, scoria smoke dust etc[1~5] The dominant components of all the outcomes are copper and lead. Moreover, in the process of tin smelting, copper contained by-products are produced, such as, crude tin alloy, tin lead electrolytic anode slime and so on. Copper content of all the products are ranging from few percentages to several tens percentage. Those products, no matter merge into main producing process, or separate treatment cost losses of valuable metal. For one hand, the containing of copper of outcomes from pyrogenic attack is less than 50%, for the other hand, a lot of valuable metal need to be processed, which increase the cost of retrieve."

Jan 1, 2013

By K. Sadrnezhaad

Industrial and experimental induction furnaces are used for melting various types of iron ingots, returned scraps and DRI sponge pellets to produce high purity cast-iron and steel heats. The lowest consumption of the electrical energy is determined for continuous feeding operation to be 0.3 KWH/Kg for production of cast-iron in 1.5-ton industrial furnace and 0.45 KWH/Kg for production of steel in 25-Kg experimental furnace. The optimum feeding rate for lowest energy consumption is obtained to be 12.5 grams per second for continuous feeding of DRI in 25-Kg induction furnace. Similar measurements show that the optimum size of the DRI pellets is around 8 millimeter.

Jan 1, 1988