Search Documents

By Chai Liyuan

Chromium-containing slag was detoxified by the method of microbial treatment using Ch-1bacteria isolated from nature by our research group, belonging to achromobacter sp. and with the characteristic of reducing high concentration of Cr(VI) in alkaline solution. The detoxifying process of Ch-1 to chromium-containing slag was studied by column-leaching techniques respectively. The results indicate that Cr(VI) in leachate can not be detected when chromium-containing slag has been column-leached for 7 days, and Cr(OH)3 content in precipitate is up to 32.8% with great value of resource recycling. Flowchart of engineering experimentation was ascertained based on the parameters of column-leaching experiments. Using the technique of pelletization of chromium-containing slag heap-leaching by Ch-1,the leaching rate of water-soluble Cr(VI) existing in chromium-containing slag reaches up to 100%, while the leaching rate of full chromium is up to 90%, when the process has been operated for 7-10 days under the conditions of 25-40C and consecutive spray by circular leachate. The content of Cr(VI) in chromium-containing slag after detoxified meet the national identification standard for extraction procedure inxicity for hazardous wastes(GB5085-1996) in China, moreover approximately 90% of Cr(VI) existing in chromium-containing slag has been recycled.

Jan 1, 2006

By J. Méndez-Nonell

The thermodynamic and chemical properties of SrSO4 and SrS in a gaseous flow of CO and CO2 at high temperature are discussed. The thermodynamic analysis of the system was made using data from the literature. The results obtained from the thermodynamic analysis were experimentally verified using the thermogravimetric technique. The experimental results suggest the formation of a complex compound between SrO and SrSO4. It was also found a change in the chemical mechanism of the process between SrSO4 and CO-CO2 and in the chemical mechanism of the process between SrS and pure CO2.

Jan 1, 1995

By Xun An

Slag from an electric slag cleaning furnace was injected with methane and air mixtures to facilitate the recovery of copper and cobalt. The effects of methane-to-air ratio, gas flow rate and temperature on the reduction and metal separation were investigated. The results showed that over 90 percent copper and up to 60 percent cobalt could be recovered from the slag with a gas utilisation of around 70 percent, as calculated by thermodynamic simulation. Methane-to- air ratio was a major factor affecting the rate of reduction under the present experimental conditions. Further, injection of gaseous reductants greatly enhanced the coalescence and settling of entrained metal droplets. A reduction mechanism is proposed and the factors influencing the coalescence of copper droplets are discussed.

Jan 1, 1998

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995

By Naiyang Ma

Along with fast growth of EAF steelmaking, better ways of treating EAF dust have been continuously pursued for better environmental protection and better economic benefits. In this contribution, various ways of collecting EAF dust in EAF off-gas cleaning systems are reviewed, and generation of dust and concentration of zinc in the dust from various collecting devices are examined. Accordingly, recycling of EAF dust through source separation is discussed.

Mar 1, 2018

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K. A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in the Fe-Pb-C system are 95.4%Fe-4.5%C-0.1 %Pb and 99.9%Pb-0.I%Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx [mass%X in molten Pb]/(mass%X in molten Fe), are 2.2, 2.2 and 1.4, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By P. R. Bruggink

"A quantitative tool has been developed to assess the impact of changes in recycling rates on the environmental impact of aluminum supply. It has been applied to the USA to forecast sources of aluminum scrap and to examine the impact of an increase in Old Scrap recovery on the USA supply system and the subsequent effect on the Life Cycle Impact of aluminum supply. The reported data for primary, secondary and import/export supply and product shipments for aluminum in the USA show a fairly good balance between supply and demand on average over the years. Therefore, it is reasonable to use the data, along with published estimates of average product lives, recycling rates and recoveries to draw conclusions about future aluminum scrap generation· and recovery. The Life Cycle Impacts of increasing post-consumer recovery rates to recover an additional 450,000 MT/yr (1 billion lb/yr) has been estimated using the model.The spreadsheet model upon which this work was based was developed in U.S. Customary units. Converting the figures to Metric units would have required converting the entire model and rebuilding the figures. I have chosen to leave the figures in U.S. Customary units. I apologize for any inconvenience this may cause."

Jan 1, 2000

By Eduard Ouerra, Nuo Jin

"The use of polytetrafluoroethylene, PTFE, as a solid sorbent for elemental sulfur during pressure oxidation of chalcopyrite was investigated. The effects of agitation, PTFE particle size and lingin sulfonate addition were evaluated using leaching conditions that were otherwise similar to those employed in the CESL process. The effects of these factors and their interactions on chalcopyrite oxidation are explained in terms of interfacial forces and solid-solid interactions. Using relatively fine PTFE powder with vigorous agitation resulted in about 100% copper extraction in less than 90 minutes without the need for grinding of the flotation concentrate.IntroductionThe extraction of copper from sulfide ores has always been dominated by the conventional pyrometallurgical smelting process. Though much effort has been made to develop various hydrometallurgical processing routes, smelting remains as the dominant process, treating approximately 80% of the chalcopyrite concentrates worldwide [1]. However, some of recently emerged techniques for treating chalcopyrite through hydrometallurgical routes are showing results that are competitive with smelting in terms of economical feasibility. Representative methods include: Activox Process, CESL Process, Anglo/UBC Process, High Temperature Pressure Oxidation, and Bio-Oxidation. Among these, the CESL processes operate at a medium temperature range (typically 140-150GC) and oxygen pressure of 100 psi, with chloride as a catalyst, and reportedly achieve copper extractions of about 95% with a light regrinding of flotation concentrate to a p95 of 45 ìðé [2]. In spite of this satisfactory extraction result, the leach residues contain significant amounts of conglomerates which contain a small amount of unreacted concentrate [2], The conglomerations are formed because the elemental sulfur generated is liquid and sticky (melting point of sulfur being 119°C), and has a tendency to wet the sulfide mineral surface, a fact which inhibits the oxidation of the minerals. The overall process chemistry of the CESL process may be summarized as follows [3]:"

Jan 1, 2012

By Tatsuzo Kitamura

The tank house of Tamano refinery, that started its operation in January, 1972, was constructed incorporating the application of Periodic Reverse Current (P.R.C.) from the outset of design works. In 1973, the production of electrolytic copper came up to 8,000 mtpm, a sharp increase ds compared with the designed capacity of 7,000 mtpm, and successful operation has been achieved up to the present. P.R.C. has been employed for the purpose of raising productivity level and reducing copper inventories. Since there were various problems in P.R.C. application to such a large sized cathode as 1 m x 1 m, special attentions were paid to the following items: -Development of a unique bus bar to make an electrolytic current to each electrode as uniform as possible. -Improvement of circulating method of electrolyte. -Application of high-performance equipment to realize a uniform spacing between anode and cathode. Owing to these creative technical developments mentioned above, technical level for operation up to 350 amp per sq m of cathode current density has been established. The quality of electrolytic copper, which was a matter of interest, has been proved to be as excellent as those of conventional electrolysis products through a long term supply to the field of SCR and Dip forming where high levels in quality are required.

Jan 1, 1976

By Robert F. Jenkins, King G. Robertson

This paper presents a practical approach for utilizing a computer model to determine the mass balance for a typical UBC recycling complex - starting with raw materials input, through scrap preparation, delacquering, melting, alloy adjustment and casting. This model is especially concerned with metal unit losses throughout the recycling complex with emphasis on metal losses at the melting furnace. The model also addresses the application of hardener alloys, metallurgical salts, chlorine for demagging, and reagents for acid gas emissions control. Other issues addressed are dross generation, acid gas emissions and dirt and fines to landfill. One benefit of the model is the conversion of annual production objectives to hourly production rates and resource requirements taking into account production schedules, maintenance downtime, and operations inefficiencies.

Jan 1, 2000

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By Leonardo Mota, Felipe Perissé Duarte Lopes, Marcelo Gomes da Silva, Sergio Neves Monteiro, Helion Vargas

"Natural fibers, as a class of material, are attracting the interest of engineering sectors owing to specific advantages such as comparatively reduced cost and lower density as well as environmental benefits associated with renewability and biodegradability. For industrial applications, thermal properties, among others, are required. These are major requirements, especially in the case of an insulating natural fiber. In the present work, thermal properties of the curaua were investigated by photothermal techniques, i.e., the open photoacoustic cell and a method based upon the monitoring of the temperature evolution as a function of time. This investigation, in tum, permitted to evaluate two important thermal properties: the thermal diffusivity and the specific heat capacity of the curaua fibers. Indirectly, by means of simple mathematical relations, the thermal conductivity was also obtained. The results were compared with other materials and characterize the curaua fiber as an efficient insulator.IntroductionMaterials are gaining attention in recent years owing to their benefits for the environment as compared to synthetics. Being biodegradable, yearly renewable and recyclable, the natural planted-based are considered fully sustainable [1]. In particular, their life-cycle, from growing to industrial processing, absorbs as much C02 as it is emitted and makes them neutral with respect to greenhouse gases responsible for global warming [2]. Typical examples of these environmentfriendly materials are the lignocellulosic fibers that have been used in simple items such as ropes, baskets, textile, modest roofing, etc, since the beginning of our civilization [3]. In the past few decades, these natural fibers have been extensively investigated [ 4-1 O] as a possible reinforcement phase of polymer composites in substitution for synthetic fibers. In fact, engineering application of lignocellulosic composites are today in the market, especially in the automobile industry [11-13]. Out of the hundreds available natural fibers, only part of them exhibits superior properties to be qualified for composite reinforcement."

Jan 1, 2011

By David Van Aken, Arpana S. Murthy, Simon Lekakh, Von L. Richards

"Three heats of 17-4PH stainless steel: with zero, three percent, and seven percent cobalt addition were melted in a 45kg (1 00lb) induction furnace under argon; and cast into no-bake molds and preheated investment shell molds. Specimens were sealed into quartz tubes under vacuum, and homogenized at 1200°C from 2h to 72h. Computational thermodynamics and optical microscopy were used to predict and characterize the microstructures. The lath martensite packet size and the amount of 8-ferrite were observed to be inversely related. A compromise between decrease in segregation and increase in lath martensite packet size was chosen for the optimum homogenization treatment. The specimens were austenitized, quenched, and characterized for retained austenite using x-ray diffraction. Age hardening kinetics were studied at 454°C (850°F), 468°C (875°F), and 482°C (900°F); and, the activation energies for precipitation of copper were calculated. Tensile properties and Charpy V-notch impact energies were measured in the peak aged condition. Fracture surfaces were observed using scanning electron microscopy and Energy Dispersive Spectroscopy. The addition of cobalt was found to be beneficial for the improvement of strength as well as notch toughness.IntroductionSegregation in the as-cast condition is one of the drawbacks of metal casting. This paper presents a study on the homogenization treatment of 17-4 PH cast stainless steel and the effect of cobalt addition on tensile properties and Charpy V-notch toughness. Lattice dilatation studies show that additions of up to 6% Co to iron has a negligible effect on the lattice parameter, whereas both the modulus of elasticity and shear modulus increase with increasing cobalt additions5• An ordering reaction has been reported in cobalt-containing, maraging steels and contributes to the hardening during ageing1-4• Although, cobalt addition in maraging steels has been extensively researched, and has been reported to be beneficial; it has not been explored much in other age-hardening stainless steel systems. In a previous study, the addition of 3% Co in cast 17-4 PH martensitic age-hardenable steel was found to improve the strength and elongation while maintaining the charpy V-notch toughness6."

Jan 1, 2011

By Kafui Nyavor

Acid mine drainage (AMD) is presently the biggest single environmental problem facing the mining industry. New and expanding metal mines in most parts of the world have to demonstrate their ability to contain this problem to obtain operating permits. Conventional methods of controlling acid mine drainage have primarily been limited to collecting the drainage and neutralizing with alkaline materials which do not provide a permanent solution to the AMD problem. Since acid mine drainage results from the oxidation of sulfides in the presence of oxygen, water and iron-oxidizing bacteria, controlling any of these three factors contributing to pyrite oxidation provides a potential at-source remedy for reducing or preventing acid mine drainage formation. Physical properties such as hydrophobicity also play an important role in the attachment of bacteria, adsorption of oxygen, water, and other ions that subsequently lead to the oxidation of pyrite. In this communication, the suppression of pyrite oxidation by treatment with fatty acid amines (FAA) was investigated. The FAA treated pyrite samples were tested at various conditions of temperature and pressure. At an elevated oxygen pressure of 500 psi and a temperature of 600 C, less than 0.2% oxidation was obtained for the FAA treated pyrite samples, while over 1.2% oxidation was obtained for the untreated samples in 10 hours of oxidation time. Accelerated column oxidation tests at ambient condition showed that FAA mated samples reduced pyrite oxidation by at least 75% in 81 days.

Jan 1, 1994

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987