Search Documents

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By A. Perillo

The process, realized in. the Kivcet furnace, can convert continuously lead concentrates, residues and secondary lead bearing materials into a lead bullion free of sulphur and a discardable slag. The lead recovery can be up to 99%. The long experience of about three years at Portovesme demonstrates the capability of the furnace to smelt a very. high range of lead raws without interruption of the operation. The operating costs are very competitive in comparison to the traditional technology. The work place and environment are clean and new tight regulations for the? hygiene control are met. The Kivcet furnace can be considered as consisting of three parts (reaction shaft, waste gas shaft and electro-furnace) connected with a common hearth. The technical basis of the furnace construction is the application of a number of design elements .which have mostly been used before in designs of industrial furnaces, such as open hearth furnace, refining furnace and other furnaces dealing with liquid meta1s. Refractory wear in the reaction shaft with typical pattern from watercooling soon has been stabilized and since maintained. No deformation of the furnace shell and no leakage of metal or s:l:ag through the bottom is? appeared after three years' operations.

Jan 1, 1990

By Christine P. Viecelli

As Phelps Dodge Corporation addresses the environmental challenges of the 1990's, water management has become a key element in an overall waste minimization strategy. The Phelps Dodge Hidalgo copper smelter has implemented a comprehensive water management program that includes management of both fresh and process water utilized by its pyrometallurgical operation. Two major technological strategies are being implemented. They are the design, construction and operation of a raw water pre-treatment facility to allow increased evaporation within cooling towers thereby minimizing blow down, and the use of a brine concentrator to treat and recycle significant quantities of process water. The end result of this program is a significant reduction in raw water pumped from the underlying aquifer into the facility as well as a decrease in process water which must be impounded or otherwise treated.

Jan 1, 1992

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By G. Djambazov, V. Bojarevics, K. Pericleous

The AC electromagnetic (EM) field effects are investigated for the possibility to extract particles (impurities, precipitates, oxides, bubbles, etc.) from molten silicon during the directional solidification of silicon ingot. The dynamics of particles are affected by the hydrodynamic drag, buoyancy, turbulent fluctuations and the EM force via the local pressure distribution. The EM force leads to high mixing rates, transitional flow structures and turbulence of the melt, contributing to the particle dispersion, transport and separation to a desired location. Application to silicon kerf loss recycling by melting and solidifying in the presence of AC EM field is presented for a variety of cases using 3D models for general flow structure and axisymmetric models for moving solidification front long time tracking. This paper demonstrates the effects of flow on the time dependent particle ‘swarm’ transport and the eventual modified distribution in the final ingot.

Mar 1, 2017

By Robert W. Bartlett

Biooxidation of an ore heap containing only a few percent of sulfide minerals requires insertion of a very large amount of oxygen either by natural air convection, forced air ventilation or gaseous diffusion. While shallow heaps, those with lateral distances much greater than their height, are of great interest for many heaped ore processing operations, natural convection is often ineffective for oxidizing them because of inadequate lateral flow into the heap's interior. Oxygen can diffuse into a shallow heap from its upper, horizontal surface in contact with air. Oxygen diffuses through the air-filled void space within the heap, driven by the oxygen concentration gradient resulting from internal oxygen depletion caused by mineral oxidation. Oxygen diffusion, coupled with the chemical reaction kinetics oxidizing the sulfide minerals, is analyzed for conditions of rapid mineral oxidation kinetics, requiring small mineral grain sizes, and for typical ore heap biooxidation parameters. Practical limits on heap heights are presented for effective biooxidation of the sulfide minerals within times of interest for heap biooxidation of refractory sulfide gold ores, one to three years.

Jan 1, 1995

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By T. Mason, R. Macko

Electroless nickel (EN) coatings are widely used in the manufacture of automotive parts, providing uniform coating, corrosion protection, wear resistance and lubrication. In contrast to EN plating benefits, the disposal and treatment of waste solutions can cause many difficulties. The use of electrochemical treatment technology greatly improves _the operation of the main wastewater treatment process and reduces operation costs. A new, state-of-the-art job shop in the Chicago area, which provides EN plating for the automotive industry, has installed a large separated electrolytic cell for the treatment of spent EN solution (from dumps and wastewater). The waste/wastewater is handled by the separated electrolytic cell, batch treatment system, filter press and neutralization station. The implementation of modem electrolytic technology and auxilliary equipment provides an effective waste treatment process that meets environmental compliance criteria.

Jan 1, 2000

By Ullrich Kammer

Metaleurop's secondary lead smelter at Oker produces 60.000 mtpy of lead and lead alloys. More than 8O2 % of the raw materials are spent lead acid batteries. The other 2O2 % consists of drosses, ashes, scrap lead, type metal, sludges, etc., and is processed in a short rotary furnace (SRF). Also, industrial batteries not fitting in the battery scrap treatment plant are processed in the SRF provided with gas/oxygen-burner. Till Sept. 199O2, a soda ash slag was used in the SRF-smelting similar to the rotary kiln-smelting at Oker. Facing the future problems of handling and dumping soda ash slag, Harz-Metall GmbH has improved SRF-smelting with a non¬hazardous slag, insoluble in water, easy to dump and cheap in fluxes. This slag is based on a CaO-SiO2 -Fe0-type. Aim of the slag smelting is to be within the temperature range of 2 1100° and 1200°C - the eutectic line of Olivine in the corresponding ternary system. Since Sept. 199O2 Harz-Metall GmbH has operated the SRF with an "Olivine-type slag" with good results. Although the material is a "leady" slag. HMG is optimistic of using it as a filling material for construction purposes.

Jan 1, 1993

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Kwong. Kyei-Sing

Gasification is a process that converts a carbon feedstock into synthesis gas (CO+H2). Slagging gasifiers operate at high temperature and pressure and in a corrosive-wear environment from the slag. Cr2O3-based refractory linings are used to protect the steel vessel that comprises the gasifier from the aggressive gasification environment. Increasing service life of the gasifier is one of the keys for wide spread development of this technology. In support of the goals, research on the gasifier atmosphere, the slag chemistry, the interaction of Cr2O3 refractory with different feedstock mixtures (e.g., coal and petcoke) were characterized by post mortem analysis of bricks from service in gasifiers and thermodynamics simulation of the environment. Examples demonstrating how thermodynamic calculations can explain the post mortem results and make predictions of material interactions will be given. Attention is placed on the possibility of Cr+6 in different feedstock mixtures and operating conditions.

Jan 1, 2010

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By H. Yin, T. Emi

"Advantages of gas/flux injection technology as materialized in the main stay unit processes for steelmaking are depicted covering hot metal pretreatment through secondary refining. Current status of micro-kinetic issues involved in the injection technology are reviewed including gas-in- metal, gas-in-slag, flux-in-metal, metal-in-flux and three-phase dispersion systems with reference to macro-kinetics. Key problems are briefly addressed to further develop injection technology for steelmaking processes.1. FROM PAST TO PRESENTApplication of gas injection to steel industry started in early 1950's when inert gas bubbling via stopper rod, lance, or porous refractory plug was practiced to make the temperature of steel melt in ladle uniform The gas bubbling in ladle was then extended to slightly removing hydrogen ti'om the steel melt tapped from Electric Arc Furnace (EAF) and Basic Open Hearth Furnace (BOH) when vacuum processing facilities were not popular. Later, oxygen gas injection via calorized steel pipe into molten steel bath in BOH Furnace was also put into operation to promote the decarburization to increase the productivity of the process. This line of development has been made in parallel with more profound processes, i.e, top blowing Basic Oxygen Furnace (BOF) for primary steelmaking and side blowing Argon Oxygen Oecarburization (AOD) vessel for decarburizing stainless steels.On the other hand, injection of fluxes into steel bath was first industrialized in Germany in 1960's, Primary objective was to desulfurize steel melt in ladle by injecting CaC2 or CaCrCaO mixture via lance under neutral slag cover with good success. Difficulties in injecting fluxes without clogging and rippling at a desired flux/gas ratio, and durability of injection lance were resolved in due time to bring forth many injection facilities to flourish for versatile refining operation. Top injection of fluxes from main oxygen lance to BOF was also industrialized as LDAC to promote early slag formation. A new process then emerged which injects oxygen gas and fluxes together through concentric annular tuyere, installed at the bottom of the BOE into steel melt. This process, developed in Germany [Oxygen Bottom Maxhutte (OBM)] and brought into maturity in USA (Q-BOP) and Japan in a large scale operation, became the predecessor of the combined blowing (top and bottom blown) BOF which dominates modern steelmaking."

Jan 1, 1996

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009