Search Documents

By Tianjiao Luo

Some literatures discussed on how to recycle the various reagent, but the discussion on how to reuse the waste liquid directly is very little. How to reuse the waste liquid directly was researched in this paper. Firstly, the waste liquid should be filtrated to remove the impurity; then some quantity of H2O2 solution was dripped into the waste liquid to pretreat it; finally, CuSO4solution was added into the treated waste liquid and the pH was adjusted to about 12, then some HCHO solution was added into the waste liquid, in which the treated carbon fiber can be plated. The morphology and composition of coatings were investigated by means of Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS), the deposition rate was mensurated by the way of dissolution. The results indicated that, the plating effect was basically identical with new plating solution, and the solution is stable, and the plating rate is still about 0.8µm/h, and the copper coating is even and combines closely with carbon fiber. According to this way, the waste liquid can be reuse 5~7 times.

Jan 1, 2006

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By G. A. Bala

As part of ongoing research to define mechanisms of microbial enhanced oil recovery (MEOR), this work describes the activity of Bacillus l1chen1formis JF-2 (ATCC 39307) Mosurfactant against crude oils with varying compositions. Surfactant based MEOR improves oil recovery by lowering the oil/brine interfactal tension (IFT) therefore permitting oil to be displaced or solub1lized into the aqueous phase.? MEOR is an Enhanced Oil Recovery (EOR) process which allows for the introduction of chemical and miscible fluids, in the form of microbial metabolic end-products, through the injection of microorganisms into the reservoir or stimulation of indigenous reservoir microbial populations. These microorganisms represent a replenishable in situ source of acid, gas, biopolymer, solvent, or surfactant products which can be. supported and manipulated by the addition of simple and inexpensive nutrients to enhance the recovery of oil. Microbially mediated surfactant production represents one mechanism of MEOR. Bacillus licheniformis JF-2. has been used in a mode 1 MEOR system based on Berea sandstone cores (permeabilly .85 to 400 md) to examine surfactant based MEOR of medium to heavy crude oils (API gravity 38.1° to 17.5°). Enhanced oil recovery was achieved with all oils tested using either cell free culture supernatants or microbial suspensions as injectants with no detrimental effect to the oil. Spatial distribution of cells following mf?crobtal flooding was analyzed with scanning electron microscopy. Data indkate complete distribution of cells with a predominance of organisms located distal to the point of injection. There appears to be no sign:if1cant recovery trend with respect to oil composition.. The biosurfactant produced by Bacillus lichen1form1s JF-2 lowers the interfacial tension of all oils tested equally well.

Jan 1, 1991

By Thomas J. O'Keefe, Pu Yu, George Houlachi, Xuewen Tang

"Impedance measurements were used to investigate the electrochemical characteristics of acidic zinc sulphate electrolytes containing Sb3+, gelatin and their mixtures. The data were correlated with cyclic voltammetry curves made using synthetic as well as industrial electrolytes. The cyclic voltammetry results were similar to those obtained in previous studies in that antimony caused a depolarizing effect while gelatin gave an increase in the potential for zinc nucleation on an aluminum substrate.The electrochemical impedance spectroscopy (ElS) evaluations were conducted on electrodeposited zinc at three overpotential values. The potentials were chosen to represent various current density regions in the zinc polarization curves. The antimony and gelatin gave characteristic impedance plots which correlated with expected behavior, particularly current efficiency. Both antimony and glue appear to modify the intermediate zinc reaction sequence, but in different ways. The data strongly suggest that film formation and stability are major factors in the zinc ion reduction mechanism.IntroductionThe zinc electrodeposition process is sensitive to the presence of a variety of organic and inorganic chemical species in the electrolyte [I]. Such components can produce either beneficial or harmful effects, depending on their relative concentrations and electrochemical behavior. Extensive investigations have been made to gain a better understanding of the changes occurring during zinc deposition in the presence of such additives. Techniques employed include microscopy, x-ray diffraction, dynamic voitammetry, current imd energy efficiency studies [2-5]. Ultimately, the objectives are to identify the factors which most affect the efficiency of the process and to provide a means to effectively control them.One of the most harmful impurities is antimony, which can be detrimental when present at concentrations as low as 10 to 20 parts per billion. Dramatic changes in zinc polarization behavior, deposition structure and current efficiency have been observed with antimony in the electrolyte. Antimony appears to lower the hydrogen overpotential by hydride formation or a similar catalytic mechanism, which allows an increase in localized corrosion and zinc dissolution [6-8]."

Jan 1, 1997

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By Paul Van Negan

During the last decade, MHO has continued to diversify the feed. of its Hoboken smelter. The range of feed materials including larger proportions of precious metals has been extended and the production of minor metals has been developed. These diversifications have required further improvements at the smelter. Attention has been particularly focussed on an increase of productivity, compliance with emission standards and achievement of the highest recoveries of valuable elements. The assaying and sampling facilities have been considerably expanded and the different processing steps of the smelter are now also systematically controlled and managed by simulation models. The charge preparation at the sinter plant, returns handling, sinter conditioning and corresponding ventilation systems have been completely renewed. The annual smelting requirement is now achieved with two blast furnaces instead of three. This is the result of rebuilding and enlarging one of the furnaces and, of a completely new concept of the charge proportioning and charging systems, together with oxygen enrichment and blast air preheat. Ventilation capacity has also been drastically increased. A 7 MVA electric furnace for cleaning the slag from both blast furnaces. contributes to improving the overall metal recovery.

Jan 1, 1990

By Bernd-Arno Behrens, Klaus-Georg Kosch

"In times of increasing energy costs automotive lightweight construction is gaining in importance. This paper deals with the production of hybrid steel-aluminum compounds by forging. The compound forging process is a promising method to successfully manufacture functional parts by applying resource-saving process steps. Nevertheless, challenges resulting from different material properties must be solved.The heating of hybrid material work pieces made of steel and aluminum is a great challenge. Steel is forged at a temperature of at least TSt =900 °C, while aluminum should not exceed a temperature of TA1= 500 °C. For achieving the required temperature gradient extensive experimental investigations have been carried out. Intermetallic phases form during the manufacturing process and can influence the bonding and the global part quality. In addition, methods for the characterization of the joining zone between the materials steel and aluminum are analyzed and the factors influencing the formation of intermetallic phases are determined experimentally.IntroductionIn times of increasing energy costs and stricter conditions relating to environmental protection, automotive lightweight construction is gaining in importance. The production of hybrid compounds by forging is a promising method to manufacture functional parts by applying resource-saving process steps. In compound forging a hybrid raw part consisting of a solid core, which is enclosed by a hollow casing, is joint in the forming process. This results in a graded material structure in the part in which the mechanical properties can be specifically adapted to the requirements. Compound forging is the form joining and/or firmly bonded joining of at least two different materials while plastic shape forming occurs (Figure 1)."

Jan 1, 2012

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

By Claire A. Chanenchuk

Catalytic Extraction Processing (CEP), a technology commercialized by Molten Metal Technology, Inc., a US.-based company, can convert industrial, household, and government wastes into commercial resources. CEP is an innovative elemental recycling technology that uses a molten metal bath to completely dissociate hazardous or toxic components of a feed and convert them to valuable products. The catalytic action of the molten metal bath converts the feed to its elemental constituents and the reducing atmosphere prevents the formation of any dangerous byproducts (NOx, SOx, dioxins, furans, etc.). Selective reactant addition allows engineering of valuable products from otherwise unexploited resources. Synthesis gas is generated from hydrocarbon feeds, ferro-alloys from metallic wastes, and ceramics from select inorganic species. Commercial-scale processing of multiple wastes and waste surrogates has been carried out at a destruction and removal efficiency exceeding 99.9999 wt.%, validating theoretical predictions. Unlike conventional hazardous waste treatment technologies, CEP offers resource recovery, minimal byproduct generation, and the potential for closed-loop recycling.

Jan 1, 1994

By Renato G. Bautista

"The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.IntroductionThe understanding and the elucidation of the mechanism of the rate phenomena for a specific chemical reaction system is of prime importance in the development of a successful chemical process. The development of successful emerging technologies for metals separation will depend on the accurate interpretation of the intrinsic chemical reaction kinetics and the rate of mass transfer of the desired metal species during its separation from the undesirable chemical species. This is the case whether the process application is for separation, concentration, and /or purification.The chemical processes that will be examined in this presentation will include leaching, solvent extraction, membrane separation, precipitation, and electrodeposition."

Jan 1, 1996

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By C. Y. Tang, Z. H. Chen, T. C. Lee

"In sheet metal forming process, the forming limit and strain distribution are governed by plastic instability and fracture following strain localization. It has been proved that the temperature gradient caused by plastic deformation as well as friction is one of the crucial factors to induce the strain localization in high-speed metal forming processes. In this paper, a numerical simulation of the sheet metal extrusion process has been conducted by using thermal-mechanical coupling finite element method. An improved mixed finite element method has been used to solve the large deformation elasto-plastic problem. In thermal phase, the transient heat transfer finite element method together with the Crank-Nicholson algorithm has been employed to determine the temperature field. Both the numerical results and the experimental observations reveal that the temperature gradient plays an important role in inducing the strain localization, which eventually leads to fracture failure in the sheet metal extrusion process.IntroductionSheet metal extrusion is such a process where the extrusion punch penetrates into one surface of the sheet metal material to let it extrude and flow towards the outlet of the die. This process can be used to produce protruding parts on a strip material. In engineering applications, the quality of the product is affected by many factors such as stress state, loading speed, material properties and lubrication condition. The research on failure mechanisms and improvement of formability in sheet metal forming processes by exploitation of differential thermal conditions has been of great interest recently [1-3]. It has been proved that the temperature gradient caused by plastic deformation, heat transfer, and friction between sheet and tools is one of crucial factors to affect 'the formability in high speed sheet metal forming processes [4]. In our previous study of sheet metal extrusion, it has been observed that plastic deformation is highly localized and some specimens are subjected to fracture failure in the form of crack propagation [5]. To understand this failure phenomenon, the effects of temperature gradients must not be ignored."

Jan 1, 2001

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By J. Smuts

The mixed-valence iron silicate ISCORITE (Fe7Si010) was identified recently in a number of ironmakingmater1als, some of which were first produced more than a century ago. Although the existence of iscorite was not reported before 1967 and published phase diagrams do not make provision for it, the morphology of the phase in all the materials that were examined suggests that it is stable under a variety of conditions. It is shown that is-corite can accommodate various foreign cations in its lattice where they can replace Fe and/or Si. The morphology of is-corite in a number of materials of different origin is shown in relation to iron oxides and silicates in optical and SEM/BSE images.

Jan 1, 1991

By Willy Persson

A common feature of the kinds and amounts of impurities present most pyrometallurgical, processes is injection of oxygen to, remove various in the feed. The degree of success of a specific process step relies critically on control of the instantaneous oxygen potential/oxidation stage, throughout the step as well as upon termination of the step. This will, for instance, determine the distribution of impurities between metal and slag. As long as the operation is perturbation free -detailed analysis of all additions and application of advanced models often yield satisfactory control means However, a pyrometallurgical process is seldom free from disturbances, which reduces the accuracy of the static models and leads to inconsistencies in scheduled route might be uncontrollable changes in quality and quantity of feed, operator interventions and shift changes, timing of cranes, lining wear and accretions etc. The implementation of dynamic, control to correct for disturbances and, more generally for process optimization, requires continuous on-line information on, the actual status of the process. The implementation of sensors for continuous process monitoring, e.g., as regards the instantaneously prevailing oxygen potential or oxidation stage, has been hampered by the highly aggressive environment in smelters; This is. where remote-sensing techniques based on optics and spectroscopy, have proven to form invaluable, tools towards the realization of dynamic production control. Since about 15 years Semtch has developed and industrialized a remote-sensing technology, based on ,optics and spectroscopy, for continuous on-line process monitoring and production control of various pyrometallurgical processes. The presentation will discuss applicability aspects with examples and experiences from installations and tests in ferrous and non-ferrous industry. Keywords: Applied spectroscopy, Metallurgy, Process monitoring, Production. Control

Jan 1, 2003