Search Documents

By Junji Shibata

As one of the effective usages of various wastes discharged in non-ferrous metal industry, the synthesis of hydrotalcite was carried out using aluminum dross as a raw material. Hydrotalcite is one of the inorganic anion exchangers and has layered structure of complex hydroxide. The removal of toxic metal ions such as As(III), As(V), Cr(VI) and Se(IV) with the hydrotalcite was investigated, and the removal properties were compared from the viewpoint of the anion exchange amount and exchange rate. Hydrotalcite can be obtained by a co-precipitation method from the aluminum dross and the waste MgCl2 solution discharged in an aluminum regeneration process. Slight amounts of SiO2, Al2O3, Fe2O3 and so on remain in the reaction product as an impurity component. Interlayer distance of the obtained hydrotalcite is about 0.3nm. Hydrotalcite changes to Mg-Al oxide by the calcination at 773K for 3h, and then hydrotalcite is formed again by a rehydration operation after calcination. The toxic metal ions are removed from aqueous solution by the anion exchange reaction in the pH region where toxic metal ions exist as the anionic species like AsO2-, HAsO42-,CrO42-, and SeO32-. The exchange amount is considerably concerned with the valence of anionic species and the size of anionic species. The removal of toxic metal ions were investigated from the engineering aspects such as the low concentration limit to be removed, the amount of hydrotalcite to be used for the perfect removal of toxic metal ions and so on.

Jan 1, 2006

By Laurentiu Nastac

"The importance of investigating solute redistribution during the unidirectional solidification of multi-component alloys is broadly discussed in the literature. A previously developed analytical model that was experimentally validated for Al-Cu, Sn- Bi and Fe-Si dilute binary alloy systems is used in this article to study in detail the solute redistribution, the liquid/solid interface stability based on an extended transient constitutional undercooling criterion and the size of the initial transient region during the unidirectional solidification of Ti-6-4 and Ti-17 alloys. A comparison between Ti-6-4 and Ti-17 alloy systems with respect to interface stability and the size of the initial transient region is also provided. The effective partition coefficients of the alloying elements in these alloys were determined based on specially designed experimental measurements.IntroductionThe importance of investigating solute redistribution during alloy solidification is broadly discussed in the literature [1-5]. One of the relevant applications of this study would be the mathematical modeling of equiaxed and columnar solidification of multicomponent alloys. This includes the instability of the solid/liquid interface. There are several mass and heat transfer processes that involve the calculation of solute redistribution during directional solidification such as industrial directional solidification processes, continuous casting, remelting processes, Czochralski crystal growth technique, floating zone techniques, etc."

Jan 1, 2012

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By C. E. Abbey, M. S. Moats

It is well known that the addition of cobalt to copper sulfate — sulfuric acid electrolytes decreases the overpotential for oxygen evolution and decreases the rate of corrosion of Pb–Ca–Sn anodes. This effect, however, has not been ade- quately quanti fied in the presence of iron and manganese in this type of electrolyte. This work provides quanti fiable data on the effect of cobalt concentration in the range of 0 –0.6 g/L in synthetic electrowinning electrolytes with and without the presence of iron. The effect of cobalt on anode potential was determined using 2 and 24 h chronopotentiometry experiments. As expected, Pb–Ca–Sn potentials increased with decreasing cobalt concentration over the range of 0–0.6 g/L Co with and without the presence of Fe. Two regression models were developed to allow plant operations the ability to predict anode potentials as a function of cobalt concentration with or without iron in the electrolyte.

Mar 1, 2017

By Admire Chaendera

A gas jet was blown through submerged nozzles to stir the bath in the presence and absence of slag. Mixing and mass transfer rates were then studied. Water and kerosene (10% by volume) were used to simulate the metal and slag phases respectively in the cold model. The mixing time (Tmix), defined at 99.66% bath homogeneity level, increased with bath height and decreased with an increase in the gas injection rate. Its value in the model vessel was related to gas flow rate (Q), bath weight (W), and bath height (H) by, Tmix = 4.39Q-0.73W0.24H1.12. Inclusion of the slag phase increased Tmix by about 16% and the mass transfer parameter, [(Reloc,r)0.25(Ret)0.32], values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with gas flow rate but decreased with an increase in bath height. The relationship, K Q0.08, showing derived mass transfer coefficient (K) dependence on the gas injection rate (Q) was established. The proportionality constant in the equation varied with gas flow rate and sample location.

Jan 1, 2006

By Richard D. Hagni

The mineralogy of dusts from the lead sinter and lead blast furnace at the Doe Run Smelter at Herculaneum, Missouri is being studied by reflected light microscopy and scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS). Oust from the sinter plant consi5ts of abundant slag and galena particles, and lesser amounts of coke, sinter, and chalcopyrite particles. In contrast, dust from the blast furnace consist of abundant coke and sinter particles, and lesser amounts of slag, galena, chalcopyrite, metallic lead and lead-copper particles. The particles in dusts from remote sampling sites !-l mile from the sinter plant and blast furnace are fine-grained and composed principally of calcium-aluminum silicates that are locally derived, but some of the larger particles consist of sinter, slag, galena, and other minerals. Additional dust samples from the plant and remote sites are currently being studied.

Jan 1, 1991

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By KNona C. Liddell

"Many metal recovery processes involve heterogeneous reactions in porous media accompanied by fluid flow and mass transfer. Modeling such systems is difficult because of the number of rate processes involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide an attractive alternative to models based on transport mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.INTRODUCTIONSubsurface mineral leaching, metal ion recovery and environmental remediation are significant modeling challenges. They involve one-, two-, or three-dimensional reactive flow in multi reaction open systems. Dissolution, adsorption, and ion exchange occur at reactive mineral surfaces, and these heterogeneous reactions are accompanied by acid-base, complexation, and redox reactions in the solution phase.Two approaches have been taken to reactive flow problems in geologic media: mixing cell and transport models. Mixing cell models, the subject of this review, are based on a network of connected cells, each with a specified number of input and output streams. Mixing cells are assumed to have no internal solute concentration gradients, that is, each cell behaves like a well-stirred tank. Gradients are represented by step changes between connected cells; this results in a model that is spatially discretized at the outset. Different methods of discretizing the model equations are considered more fully below. Although this is not strictly necessary, it has usually been assumed in subsurface flow applications that all cells in the network have the same volume and identical initial properties."

Jan 1, 1996

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering materiaL Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to dcsign new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass speetrometer.

Jan 1, 2003

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By De-Qiu Fan, H. Y. Sohn, Y. Mohassab, M. Elzohiery

A novel flash ironmaking process is under development at the University of Utah. A computational fluid dynamics (CFD) approach, coupled with experimental results, was developed for the analysis of the kinetics of reduction of hematite concentrate b yH + CO mixtures at 1150–1350 °C in a droptube reactor.

Mar 1, 2017

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of eomposition at the temperatures from 850K to 1050K. An alloy was vaeuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Preliminary experiments were conducted in a mini plant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Riyad N. Ahmad-Bita, Shadia J. Ikhmayies

"SnO2:F/CdS:In structures were prepared by the spray pyrolysis technique on glass substrates at a substrate temperature Ts = 450°C. NH4F and HF were both tried as the sources of fluorine in the precursor solution of SnO2:F. A comparison between the properties of structures obtained by using the two doping compounds was performed. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to characterize the films. The structures prepared by using HF as a fluorine source were found to have more ordered crystal growth, larger grain size and sharper absorption edge. From the inspection of the first derivative of the absorbance it is expected that more interdiffusion on the SnO2:F/CdS:In interface takes place in the structures made by using HF. These results confirm that these films are better as forecontacts for CdS/CdTe solar cells.IntroductionThin film CdS/CdTe solar cells built in the superstrate geometry rely on transparent conducting oxides (TCOs) to make the front contact The investigation of combined CdS-TCO films has recently been developed owing to the great interest of better understanding the effect of these bilayers on the absorbers [1]. Usually SnO2 is utilized as a front contact for these solar cells. Optimizing the properties of the SnO2/CdS structures is an important step on the way to get high performance CdS/CdTe solar cells.There are different methods to prepare SnOz thin films, such as reactive sputtering [2], evaporation [3], chemical vapour deposition [3, 4], dip coating [5] and spray pyrolysis [6-9]. At the same time CdS thin films can be prepared by different techniques such as chemical bath deposition [10], thermal evaporation [11], screen printing [12] and spray pyrolysis [7, 13]. However, the spray pyrolysis technique is a very low cost and simple technique that enables intentional doping and getting large area and uniform thin films [14]. For these reasons it is choused to prepare SnOz and CdS thin films in this work. To improve the properties of these compound semiconductors, SnOz was doped with fluorine and CdS was doped with indium where such doping is well known for these compounds."

Jan 1, 2012

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004