Search Documents

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Roger Wilmoth

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the U.S. Environmental Protection Agency?s, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open-Pit Highwalls Demonstration Project. This project is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome U.S., located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 metres (m) and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied insitu treatment technologies included: 1) A modified, furfuryl alcohol resin sealant, utilizing wood and agricultural by-products to coat the rock surface. 2) EcobondTMARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface. 3) Two ARD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: 1) ASTM D 5744-96, Accelerated Weathering of Solid Materials using a Modified Humidity Cells, 2) mine wall residual wall rinse sampling, 3) microscopy, and 4) core drilling followed by water injection testing.

Jan 1, 2003

By Paul Pajunen, Michael Sheedy

"Acid separation using short bed ion exchange is a now well established technology in copper refinery tankhouses. Refinery bleed streams from liberator cells are treated by short bed systems to produce an acid-free byproduct stream that contains the bleed metals and valuable nickel salts. Removing the acid eliminates the need for a black acid evaporator and reduces the amount of sodium carbonate required in nickel selective precipitation processes. The recovered sulfuric acid can be recycled to the tankhouse. This same technology is routinely used to treat other acids such as hydrochloric, nitric, and hydrofluoric. In the case of hydrochloric acid, the process can selectively separate chloro-anionic complexes such as Zn, Pb, and Cu, which are then eluted with water. The acid recovery technology can also be closely coupled with ion exchange processes in order to minimize regenerant acid consumption. In many hydrometallurgical applications resin regeneration often requires an acid dosage multiple times the stoichiometric minimum. Coupling an acid recovery bed with the IX column allows recovery and recycle of the free acid in the spent regenerant, thus reducing the overall acid consumption to just slightly more than stoichiometric.Short Bed Ion ExchangeThe short bed ion exchange process has been extensively used in the metal finishing industries since the early 1970s [1,2]. Short bed systems have also been sold to primary metals producers for the separation of sulfuric acid from copper refinery bleed streams [3] and for the recovery of nickel and cobalt from plant effluent streams. This unique technology optimizes the ion exchange process and offers a number of significant advantages over conventional ion exchange. The principal features and benefits of this technology are presented below."

Jan 1, 2012

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920's with in situ operations in the underground mine and small dumps up to the 1950's. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased' to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By Michal Rzyman, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Thermodynamic considerations indicate that heavy metal oxides should easily react with HBr, the main gaseous product from the thermal decomposition of tetrabromobisphenol A (TBBPA), forming low boiling point metallic bromides suitable for volatile separation. Mechanisms and kinetics of the bromination reactions must be well recognized prior to developing of a new treatment for the simultaneous recycling of plastic waste containing brominated flame retardants (BFRs) and metal oxides (printed circuit boards, automotive shredder residue, plating sludge, metallurgical dusts). In this work, a differential scanning calorimeter and laboratory-scale furnace were used to investigate the possibility and conditions of the bromination of ZnO by product of thermal decomposition of TBBPA. The formed solid, condensed and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography and gas chromatography coupled with mass spectrometry. Introduction Tetrabromobisphenol A (TBBPA) is the largest volume brominated flame retardant (BFR) in production today and is used in more than 70% of the world’s electronic and electric (E&E) appliances [1]. The growth in the production of E&E products and the fact they become obsolete so quickly cause significant problems in the safe disposal and recycling of the electrical and electric waste (E-waste) and other BFR-containing waste [2]. Among various treatment processes, thermal methods are most useful since they allow the recycling and recovery of both the organic and inorganic fractions of the waste. However, incineration of the BFR-containing wastes results in the emission of hazardous organobromine compounds, while the main portion of bromine released from decomposed BFRs is present in flue gas as hydrogen bromide (HBr) [3]. HBr, which is known to damage incineration systems, seems to be a very effective bromination agent for many metallic oxides present in waste. The concept of this study is to take advantage this of its property."

Jan 1, 2008

By S. Saptharishi

Selenium, which is a 6A group element of the periodic table, constitutes about 7x10-5 % of the earth?s crust. Even though selenium is a dispersed element with respect to its commercial exploitation, it is capable of forming number of minerals and nearly forty selenium minerals have been identified, out of which the copper ores are the richest sources of selenium. Electronics industries and glass industries are the major consumers of selenium, while pharma grade selenium used as micronutrient for humans and animals. Various methods have been developed to recover selenium as a by-product from copper anode slime during copper refining. Selenium being amphoteric in nature, it is soluble in both acid and alkali. While acid roast process is widely used, considerable work has been carried out in Russia for recovering selenium through alkali route. This paper enlightens the process developed at Central Research and Development Laboratory, for recovering selenium from decopperised slime through alkali pressure leaching. The decopperised slime is pressure leached with alkali under oxidizing conditions by which almost all the selenium present is converted to alkali selenate, which is easily separable from the rest of the decopperised slime. The solution so obtained is neutralized, during which, most of the impurities are precipitated out. Then selenium is precipitated in its elemental form upon purging sulphur-di-oxide under warm acidic medium. The purity of the selenium obtained by this process is higher than that of the selenium from acid roast process. Moreover selenium can be crystallized as sodium selenate and it can be marketed. The acidic content of the effluent is recovered and it is recycled back to the process. The sodium content of the effluent is converted into high purity sodium sulphate, which is marketable. The hazardous waste containing arsenic is precipitated as its sulphide and can be disposed off as landfill.

Jan 1, 2006

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Tao Zeng, Jianchao Li, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"The densities of the selected quaternary Ca0-5%Mg0-Alz03-Si02 slag with low silica were measured by the Archimedean method in a wide temperature range from l 723K to 1823K. Slag compositions were chosen based on five different levels of Si02 content between 0.00 pct and 11.40 pct. The MgO content was equaled to 5.00 pct. The mass ratio of CaO/Alz03 was varied from 0.67 to 2.14. The effects of temperature, Ca0/Alz03 ratio and optical basicity were studied. It is shown that density decrease approximately linearly with an increase in temperature. With the same Si02 content, the density decreases with increasing of CaO/Alz03 ratio and optical basicity. Based on the experimental data as the boundary of the homogenous phase region predicated by F ACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model is working well.IntroductionIt is of great importance to measure density of slag melt not only to the theory research for melt, which that is directly amenable to the structure correlations of molten slags, but also to the industrial application. Many metallurgy phenomena such as inclusion formation in molten melt and its removing, slag foaming, slag-metal reaction are closely related to the density of slag. Density is also required to estimate other fundamental properties, like surface tension, viscosity, and thermal conductivity from thermal diffusivity so that a relatively complete picture in regard to the behavior of high-temperature molten oxides could be made."

Jan 1, 2013

By Guanghui Li

In the paper, the recovery technology of gallium from zinc-leaching residue by cold-bonded coal-based direct reduction process following magnetic separation was developed. The results show that the scattered metal Ga can be concentrated obviously after the reduction of zinc-leaching residue briquette and magnetic separation of reduced product. At the same time, the volatilization of Zn in the residue is enhanced during the reduction. When the residue, bear¬ing 18.60% Zu.21.18% Fe and 527 g/t Ga, was reduced with coal at 1100°C for 150 min, the results of Zn volatilization of 9842% and Ga recovery of 89. 10% were obtained in reduction. After magnetic separation of the reduced product, the concentration of Ga in sponge iron is 2164 g/t, and the separation recovery of Ga reaches 92.42%. The enriched mechanism of Ga during reduction -separation process was studied by using electron microscope, scanning elec¬tron microscope, energy spectrum and mineralogical analysis. The investigations show that there is no formation of independent phase of Ga during reduction process. The Ga occurs mainly in metallic iron phase (the concentration of Ga in metallic iron phase is 0.04%-0,4%), in addition, there exists a little Ga in poorly crystalline sulphide (o.08%-0./5Y& Ow). But Go does not exist in most of glass and silicate phase. The affinity of Ga for metallic iron is the enrichment basis of Go in reduction, and it is also in favor of recovering Go during magnetic separation. Key Words: Gallium Zinc-leaching Residue Cold- Bonded Direct Reduction

Jan 1, 2003

By Kan Song, Lin Liu, Hengzhi Fu, Jun Zhang, Haijun Su, Xiaojiao Jia

"Al2O3/YAG/ZrO2 eutectic in situ composite has been regarded as new generation of high temperature structural material due to its excellent performance even close to its melting point. The directionally solidified Al2O3/YAG/ZrO2 eutectic ceramics are prepared by recently developed Laser Floating Zone Melting (LFZM) apparatus in which a splitter mirror is used to obtain two beams with the same quality from one CO2 laser. With the two laser beams irradiate the sample from opposite directions, the sample is zone melted. The apparatus configuration and the solidification processing are described in detail. The solid/liquid interface morphology is studied and the mechanism of microstructure formation especially the characteristic of eutectic cellular is discussed. It is shown that YAG and ZrO2 phases play a leading role during the ternary eutectic growth. Meanwhile, the relationship between the solidification microstructure and the processing parameters are investigated.IntroductionAl2O3/YAG/ZrO2 ternary eutectic in situ composite, due to its excellent high temperature mechanical properties, is now considered to be a promising candidate material as a replacement of nickel based super alloy for new generation aero space engine turbine blade [1]. They exhibit flexural strength of 360-500 MPa from room temperature to 2073K in air atmosphere [2]. The compression creep strength at 1873K is 433MPa with the strain rate of 104/s [3]. However, because of the high melting point and complex physical properties, there remain still many difficulties for its application. One of the bottlenecks is the poor understanding of the relationship between microstructure and solidification conditions."

Jan 1, 2012

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By F. J. Tavera

The column flotation technology, at first developed for application in mineral dressing, has received special attention in processing of non-mineral dispersions as a result of its low cost, high efficiency and relatively simple operation. This paper presents the results from the operation of a laboratory flotation column for the separation of vegetable oil and soap from aqueous industrial effluents, The flotation system was operated under continuous countercurrent conditions without and with additions of a cationic collector. The experiments show that it is possible to separate about 80% of the organic phase in a rougher flotation stage. These results suggest that the recovery of the organic phase is highly dependant on the dispersion characteristics (i.e. bubble size, gas holdup and bubble surface area flux) and the existing an optimum bubble size from which either smaller or larger, the recovery of the organic decreases.

Jan 1, 2003

By Keiji Toyabe

Several purifying techniques have been developed for controlling the impurity levels in the copper electrolyte at Niihama Copper Refinery. These have been carried out as follows; i ) the study of the reaction in liberation made it possible to raise the current efficiency for arsenic removal by more than 50% and to decrease generation of arsine sharply. By applying this method, a good performance was attained at commercial operation. li) the antimony in the electrolyte can be successfully removed by contacting it with activated carbon. This procedure is applicable particularly when there is a large amount of antimony in the copper anode. lli) for the nickel sulphate recovery from the electrolyte, an electric evaporating system was developed. The characteristics of this process are, capability of continuous operation with less manpower, the high recovery ratio of nickel sulphate (more than 85% as nickel) and no black acid formation in the treated solution.

Jan 1, 1987

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993

By Junwei Han, Wenqing Qin, Dawei Wang, Fen Jiao, Wei Liu

The removal of iron impurity from zinc calcine was studied by magnetization roasting and magnetic separation. The effects of roasting temperature, magnetic intensity, ore grinding, and leaching pretreatment on iron grade and recovery were investigated. The results indicated that iron recovery increased with the increase of roasting temperature or magnetic intensity, while iron grade was always less than 22%, depending on the fact that the magnetite were not liberated completely. The good liberation was difficult to be achieved by ore grinding but was easier by acid leaching, since the magnetite grains were very fine. After the leaching pretreatment, the recovery of 76.31% with iron grade of 53.24% was obtained by one roughing and cleaning. The SEM/EDS analysis showed that a part of sphalerite, zinc ferrite and other gangues were mixed into the iron concentrate, while some of fine magnetite was reported to the tailing.

Jan 1, 2016

By H. Palkowski

Recent trends in the automotive industry lead to increasing interest in advanced high strength steels (AHSS). Those steels often have a high bake hardening potential (BH), giving additional contribution to the strength of structural parts, subjected to the paint baking process. For hot rolled AHSS, namely dual phase and martensitic steels, the effect of process conditions on mechanical properties had been investigated. However, the influence of chemical composition within the range in industrial production has not been investigated sufficiently yet. In the current research, samples with different chemical compositions within the characteristic interval for industrial production are under investigation under different preload conditions and simulating the thermo-mechanical production process. The samples were then subjected to BH process. Tensile tests were performed to study the influence of varying chemical composition on the BH effect. The results of investigations on dual phase steels will be presented in this paper.

Jan 1, 2008