Search Documents

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By Bingguo Liu, Daifu Huang, Jinhui Peng

"The conditions to prepare U3O8 by calcination from ammonium diuranate were optimized, and the response surface design method was applied to analyze the influence on the total uranium and U+4 of calcination temperature, calcination time and mass of sample. A quadratic equation model for the total uranium and U+4 of U3O8 was built and the effects of main factors and their corresponding relationships were obtained. The analysis of variance shows that calcination temperature and calcination time significantly affected the value of total uranium and U+4 of U3O8. The optimal calcination conditions were as follows: calcination temperature 931.83 K, calcination time 24.32 min and 43.89 g. Under these conditions the value of total uranium and U+4 of U3O8 was 84.78% and 28.02%, respectively. The validity of the model was confirmed experimentally and the results were satisfactory.IntroductionNuclear energy is clean, effective, and a sustainable from of energy. It plays an important role in overcoming the impending global energy crisis, and in reducing energy vulnerability. In addition, nuclear energy is a possible cheaper and cleaner source of energy compared to fossil fuels, with no not really, mining of uranium produces CO2 contribution to green house gases [1]. Uranium dioxide, one of the most important fuel pellets used as nuclear fuel in light water reactors, is manufactured by calcining ammonium diuranate to triuranium octaoxide, followed by its reduction to uranium dioxide using cracked ammonia at 700°C [2]. Earlier attempts to optimize the important calcination process through several common techniques have not yielded desirable results [3]. These techniques either rely on the classical one parameter at a time approach that ignores the combined interactions between physicochemical parameters, or are theoretical in nature. Furthermore, these techniques also require large number of experimental data to be generated [4]. In order to produce triuranium octaoxide in an optimized manner, which considers the interaction of different process parameters [5], there is a need to adopt a multivariate statistical technique."

Jan 1, 2011

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By Chao Li, Lim Hongxu, Yuyue Wang, Xie Yang

"A intergrated process of sulfuric acid leaching, sodium chloride leaching, lead chloride crystallization, lead hydroxide synthesis and roasting was carried out for the recovery of lead, cadmium, copper and zinc from lead smelting dust containing various metals. The results showed that the separation of cadmium, zinc and copper from dust could be obtained after sulfuric acid leaching and corresponding leaching rate were 92.12%, 90.25% and 88.26% respectively. The subsequent sodium chloride leaching carried out for lead with optimized parameters as: sodium chloride concentration 250g/L, leaching temperature 90°C, leaching time 2h, pulp density 33g/L, 0.12mol/L CaCh; The lead compounds crystallization rate reached 86.67%, and then transferred into mPbO·nH2O, the product of 98.66% ß-PbO could be obtained through roasting under 502°C. In the end, a feasible method of ß-PbO preparation from lead containing dust was put forward.IntroductionThe pyro-metallurgy flue dust from smelting lead activities are often stockpiled and pose potential environmental risks due to the heavy toxic elements, such as Pb, Cd, As, Cu, Cl, and Zn which are contained in the dust. With the rapid depletion of rich ore resources in recent years, it has become increasingly more financially attractive to recover valuable metals from previously stockpiled dust, while simultaneously reducing the potential of environmental pollution from toxic elements contained in the dust. Nowadays, pyro-metallurgical and hydrometallurgical routes or both combined methods can be developed to treat secondary materials such as lead ash, leach residues etc. By comparison the hydrometallurgical processes are often considered more eco-friendly.Some chloride leaching processes for recovering lead have been employed using either NaCl, or MgC2 and CaCl2, or FeCl3 [1] The effectiveness of the brine leaching method is based on the formation of complex metal chlorides in concentrated chloride solutions [2] Similarly, Other metals such as zinc, cadmium and copper contained in the flue dust are often treated with sulfuric acid, hydrochloric acid, ammonium solution and sodium hydroxide etc. as lixiviants [3] The metals from leach solutions thus has been obtained by precipitation, ion exchange, solvent extraction or replacement [4]"

Jan 1, 2014

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By llya Perederiy, Vladimiros G. Papangelakis, Indje Mihaylov

"Nickel slags obtained from various smelting furnaces and converters differ in terms of their chemical composition and microstructure. The microstructure of the slag is largely affected by how fast the slag is cooled after being discharged from the furnace. Slow cooling is known to promote crystallization and growth of phases such as crystalline fayalite (Fe2Si04), magnetite (Fe3Ü4) and vitreous silica (S1O2). Slag granulation causes rapid solidification of the melt in the form of either an amorphous solid or highly intergrown crystalline silicate and oxide phases. Smelter slags contain entrapped Ni, Co and Cu in the form of dissolved oxides and matte inclusions. Extraction of the entrapped metals by high pressure oxidative acid leaching (250°C, 70 g/L initial H2SO4, up to 90 psi O2, 45 min) relies on the dissolution of the metal bearing minerals. The impact of the slag microstructure on the accessibility of these minerals to leaching, as well as the morphology of the produced residues is discussed in this paper.IntroductionIt was shown previously that entrapped base metals can be efficiently extracted from naturally cooled (as opposed to granulated) crystalline nickel smelter and converter slags using high pressure oxidative acid leaching operating at 250°C, ~40 g/L terminal acid and 60 to 90 psig oxygen overpressure [1, 2,3,4, 5, 6].Mineral characterization work performed on a naturally cooled crystalline nickel furnace slag from Vale's operations in Sudbury (ON, Canada) was previously reported [4]. Fayalite (Fe2Si04) and magnetite (Fe3U4) were detected using powder X-ray diffraction. These two minerals as well as silica (S1O2) and matte ([Fe,Ni,Cu]Sx) were also identified with the help of energy dispersive X-ray spectroscopy (EDX) on cross-sectional images obtained with a scanning electron microscope (SEM) operating in the backscattered mode. Nickel converter slags obtained from Vale's operations in Sudbury were found to be mineralogically similar to the furnace slag, but with higher contents of matte entrainment and magnetite based on the SEM-EDX observations [6]."

Jan 1, 2012

By Tobias Pröll, Bernhard Kronberger, Joachim Rohovec, Werner Hölt, Hermann Hofbauer

"As this is only a first draft, more precise explanations as well as detailed schemes, figures and plots will be included in the final draft. The description og the 100 kW test rig will also be mor detailed as construction is ongoing and will be finished during the summer. Furthermore simulations are to be finished shortly; so details on combustibles and gas concentrations will also be included in the final draft.AbstractOxyFuel combustion is a key technology for the efficient separation of CO2 from fuel combus¬tion (especially coal). Since coal plays a minor role in the Austrian energy mix the application of OxyFuel towards other fuels (biomass, waste fuels) is interesting to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alter¬native fuels is also interesting from a strategic point of view in order to generate knowledge for operation of capture ready cofiring and waste/sludge-incineration plants. OxyFuel uses a synthetic mixture of 02 and recycled exhaust gas where the 02 content may vary. This supplementary degree of freedom allows improved operation especially for low calorific fuels. Heavy fuel oil addition for low calorific combustibles can be omitted when using OxyFuel combustion. Application of alternative fuels (wood, waste wood, municipal waste, sewage sludge) in a 100-kW CFB plant is investigated in combination with process simulation.IntroductionOxyFuel combustion is discussed as one of the key technologies for the efficient separation of CO2 from combustion of fossil fuels (especially coal). Since coal plays only a minor role as primary energy source in Austria, the broadening of the scope towards OxyFuel of other fuels like biomass or waste fuels is necessary to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alternative fuels besides the large coal-oriented projects is interesting also from the strategic point of view. The presented project aims at the generation of knowledge in order to design and operate capture ready cofiring and waste/sludge incineration plants."

Jan 1, 2008

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014

Cuspidine (3CaO?2SiO2?CaF2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel. The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiOrCaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been determined by an electromotive force method using CaF2 as solid electrolyte and a transpiration method as follows: The chemical potential diagram and constituent activities for the CaO-Si02-CaF2 system have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By Rina Kim

There are many factors which affect the gold cyanidation mechanism— mineral composition, free cyanide and dissolved oxygen (DO) concentrations, heavy metal additions, etc. This study combines electrochemistry and surface analysis methods to examine the effectiveness of the above factors on gold cyanidation process. Three gold ore samples were used in this study. Sample 1 was a pyrite concentrate, contained mercury and silver. Sample 2 also contained sulfide minerals, including galena. Sample 3 contained pyrite with sphalerite and galena. In the case of samples 1 and 2, the presence of heavy metals enhanced gold cyanidation kinetics, though the addition of higher DO was not effective on improving the kinetics. Sample 3 showed an opposite behavior: the kinetics was not enhanced by galena, because of its relatively small amount, however, the use of higher DO made improvement in the gold leaching kinetics, likely caused by iron species generated by pyrite oxidation.

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

Thallium is a very minor element found in lead ores. It's behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

Thallium is a very minor element found in lead ores. It's behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994

By D. J. Donaldson

The PAL process for recovering nickel from laterite ore requires large volumes of thick abrasive slurry to be raised lo high temperature (245°C+) and pressure (40 atm.+). Flow diagrams of the process typically result in facilities that have serious operating and reliability problems. Most of the problems can be attributed to using multiple pump stations to raise the slurry to autoclave pressure, large amounts of flash and live injection steam to heat the slurry to autoclave temperature and several steps of flash cooling to lower the temperature and pressure of the abrasive autoclave slurry down to atmospheric conditions. It is proposed that operating and reliability problems of PAL facilities can be mitigated by using Tube-in-tube heat exchangers and "float type" positive displacement pumps. The subject paper describes an innovative application of such equipment in the facility design of the PAL process. Keywords: Nickel, Laterite, PAL, Heating, Slurry

Jan 1, 2004

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996