Search Documents

By L. -C. Lai

A series of LaNi5-based alloys, with partial substitution of Ni by Al, Co, or V, were prepared The gas-phase hydrogen absorption kinetics and pressure-composition-temperature curves were measured The activation became easier and the plateau pressure was reduced as Ni was partially substituted by Al Substitution with Co reduced the hysteresis as well as the hydrogenation capacity, but enhanced the absorption kinetics Vanadium is often considered as a hydride former, but when it was added to LaNi5, it was found that V occupied the B site. A small amount of substitution of Ni with V led to a higher hydrogenation capacity and faster activation rate Based on these properties, an alloys LaNia 25CO0.5V0.1Al0. 15 was fabricated as an electrode. Compared with LaNi4.85Al0.15, it was found to exhibit faster activation, higher discharge capacity, and longer cycle life. The variation of the hydrogenation characteristics is discussed based on the physical and chemical properties of the alloying elements.

Jan 1, 1997

By Dhanesh Chandra

Long term stability studies were conducted on four variants of LaNi5; 10,000 hydriding/dehydriding cycles were used to evaluate their suitability for a metal hydride cooling system. Thermodynamic and structural studies were conducted to determine changes in these materials during cycling test period. The hydrogen sorption properties of LaNi5.2, and Lao 9Gd0.1Ni5 and LaNi4.75In0.27 were seriously degraded during the tests but the LaNi4.8Sn0.22 hydride was virtually unaffected. Hydride isotherms were measured at the beginning and at intervals through out the test period to observe the nature and extent of damage degradation in the sorption properties. X-ray diffraction studies of the alloys (LaNi5.2, LaO.9Gd0.1Ni5 LaNi4 8Sn0.22) and their respective hydride, before and after test, provided insight with regards to the observed changes in the hydride properties. Electron microscopic studies were also conducted to evaluate the changes in particle sizes.

Jan 1, 1989

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By Hector Carreon

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current condition of such turbine component. By using eddy current images, it was shown that the eddy current technique could be used to monitor creep damage in a nickel base super-alloy. The eddy current results also show a significative variation in the electrical conductivity on the creep damage zone with respect to the background zone in nickel-base super-alloy samples. In addition, the absolute thermoelectric power coefficient show also a strong dependence associated with creep damage in nickel base super-alloy samples using a copper hot tip reference. The eddy current and thermoelectric power techniques seems to show promise as nondestructive evaluation tools for monitoring the level of creep damage in metallic alloys.

Jan 1, 2010

By Henry Salomon-De-Friedberg

Quebrada Blanca has had to overcome numerous challenges in achieving design throughput. The paper reviews how actual practice has evolved from the original design. The major challenges that were encountered from heap leaching to solvent extraction, the tankfarm and through to electro winning are discussed. The eventual solutions to some of the key issues are presented.

Jan 1, 1999

By J. R. Donald

For processing copper, continuous converting has been successfully employed in a variety of locations, but for nickel, there has yet to be a successful commercial implementation of continuous converting technology. At Inco?s Copper Cliff smelter, there are specific requirements for the production of Bessemer matte relating to downstream processing that makes continuous converting for nickel mattes even more challenging. The nickel carbonyl refineries require very low iron levels in the matte, and the sulphur deficiency must be carefully controlled such that the appropriate quantity of PGM-rich metallics are produced from matte separation. The present paper outlines continuous converter technologies that have been implemented in copper, and evaluates their potential for nickel converting. The challenges of producing a Bessemer matte to the required specifications are discussed. The economic and environmental driving forces, and the challenges of justifying a novel technology in place of productive existing equipment, are discussed.

Jan 1, 2005

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral's Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By James M. Lockwood

"Eureka Technology has developed and patented a technology for the recycling of EAFD. Through this process all constituents of the material become salable commodities or are returned to the steel making process. In transforming the EAFD ""waste"" stream into a ""process"" stream the Steelmaker eliminates potential liabilities and the uncertain future of current processes while further reinforcing its role as a recycler. This is a cost-effective and energy efficient technology that combines hydrometallurgic and electrolytic processes resulting in the recovery of salable metals. For instance, unlike pyrometallurgic processes, zinc is recovered in metallic form and no elements are volatilized. This on-site operation also eliminates expensive transportation costs. In summary this technology reduces the cost of dealing with EAFD by recycling material currently being landfilled.IntroductionWorld crude steel production reached a new record level in 2007 - 1.34 billion tons of which 31% was produced by EAF steel makers [1]. This resulted in the generation of over 6 million tons of EAFD. This steel byproduct contains significant amounts of lead, cadmium and other hazardous metals. In the United States the Environmental Protection Agency (EPA) has designated EAFD a hazardous waste (EPA waste code K061). With over 50% of steel production in the US coming from EAF steel making this byproduct represents the single largest source of solid hazardous waste generated."

Jan 1, 2008

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By M. Ashraf, P. J. Hazell, A. A. H. Ameri, J. P. Escobedo-Diaz, N. N. Elewa

A novel methodology to estimate the dislocation density in cubic metals by using microhardness measurements has been established. The proposed methodology is based on the Indention Size Effect (ISE) phenomena and strengthening mechanisms of materials at the micro-level. The methodology was validated by using experimental data of lean duplex stainless steel 2101 alloy. The results are confirmed via X-ray diffraction measurements and they substantiate that the proposed approach can be used as a general method to estimate dislocation density in metals.

Mar 1, 2017

By Fathi Habashi

In the past five years Cuba has been attempting to more than double its nickel production by constructing two new ammonia leaching plants. No metals are yet produced on commercial scale but a variety of oxides and sulfides. This report updates the Cuban nickel industry as a result of two visits : one at the invitation of the Cuban Ministry of Basic Industries in 1987 and the other as a consultant to the United Nations for the Cuban Laterite Project in 1989.

Jan 1, 1993

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By Takeshi Azakami

By combining the iron reduction process with the usual rotary kiln process, the direct production of metallic zinc from EAF dust is proposed. After thermodynamic estimation and desk-top experiments it is confirmed that the process is hopeful under suitable conditions. In order to get some practical test data the enlargement of the process scale was planned and the bench scale tests were carried on successfully. In these experiments a zinc ingot of PW grade was produced from EAF dust.

Jan 1, 2003

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999