Search Documents

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By S. Gupta, M. Fuka

This paper reports for the first time the synthesis of deintercalated MoAlB particulates which belongs to a family of novel ternary borides called MAB phases by selected etching of Al from these particulates by treating them with a solution of LiF and HCl. The FESEM analysis showed that these particulates hada stacked 2D-particles like morphology reminiscent of multilayered MXenes, but unlike MXenes, the 2D layers were interconnected with anisotropic porosity between them with an average length and width of pores being 257 ± 126 nm and 35 ± 10 nm, respectively. The EDS analysis of particulates showed that a typical particulate had a chemistry of (Mo Al )B{O F } which indicate partial 0.67 0.33 0.19 0.02 deintercalation of Al from the particulates. These novel particulates were also referred to as MABenes due to their microstructural similarity with multilayered MXenes.

Mar 1, 2018

By Ping Long, Peipei Liu, Xinlin Ren, Yunke Wang, Bin Yang, Jian Wu, Wenli Zhang

In this research, ICP-AES was used for determining ten impurity elements (Fe, Pb, Ca, Mg, Cu, Zn, Al, As, Sb, and Bi)in tin concentrate and smelting products, such as crude tin and slag. Samples were dissolved by hydrochloric acid and nitric acid. Determination conditions were investigated in detail. Influences of matrix and coexisting elements were eliminated by selecting proper analysis spectral lines. Under the optimum conditions, the correlation coefficient of cali- bration curves were higher than 0.999. The detection limits of these ten impurities were in the range between 0.0009 to 0.0621 lg/ml. Relative standard deviation (RSD) values were lower than 6.0%, and the recoveries of standard addition were between 85 and 109%. The proposed method was demonstrated to be reliable by comparingwithstandardanalysismethodsandcertifiedvaluesofstandardsample. It could be applied for determining impurity elements in tin concentrate and smelting products successfully.

Mar 1, 2017

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By Jian Li, Pei Liu

In recent years, focused ion beam (FIB) has become a powerful microscopy tool. Creating large FIB cross sections are often required to characterize important microstructure features e.g. the depth and morphology of pitting corrosion and stress corrosion cracking in natural gas pipeline steels. Large FIB sectioning often takes long time that not only occupy valuable FIB microscope time, but also consume often expensive consumables that include gallium ion source, aperture and deposition gas etc. The new plasma FIB developed by FEI can speed up milling process by using much larger beam current. However, for most of the laboratories that is limited by conventional Gaion FIB, the milling speed is limited by the relatively small beam current. In this paper, FIB milling rate are studied against milling parameters that include beam dwell time and pixel overlap. By optimizing the milling parameters, milling rate can increase significantly.

Mar 1, 2018

By Robert R. Grinstead

Two new ion exchange resins have been developed, which selectively absorb copper and nickel in preference to ferric iron from dilute sulfuric acid solutions of pH 1-3. The first absorbs copper and not nickel and can be readily eluted with 1-2N sulfuric acid. This resin is well adapted to the processing of copper leach liquors, including relatively low grade liquors obtained from dump leaching. The second resin absorbs nickel as well as copper in the same pH region, but only the nickel is eluted with 1-2N sulfuric acid. Elution of the copper requires much stronger (ca. ION) acid, altho both species are readily eluted with dilute (ca. lN) ammonium hydroxide. This resin, which should be useful in processing of certain types of copper-bearing solutions, may also be suitable for treating acidic nickel leach solutions of laterites and other non-sulfide ores.

Jan 1, 1976

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By Corby G. Anderson

Over the past 15 years, numerous pressure oxidation plants for pretreatment of gold ores and concentrates have been installed throughout the world. While this technology is now established, it suffers in terms of the complex engineering and operational characteristics inherent in utilization of high temperatures (i.e. up to 225oC) and high pressures (i.e. > 3000 kPag). This paper outlines the application of an industrially proven pressure leaching methodology utilizing nitrogen species catalyzed pressure leaching and alkaline sulfide gold leaching. As such, it stands as an economic and engineering advancement in pressure leaching and non-cyanide treatment of gold ores and concentrates. In particular, the technology offers significant technical and economic advantages over traditional pressure oxidation and cyanide gold recovery in the treatment of gold bearing chalcopyrite ores and concentrates. An example of this will application will be delineated in this paper.

Jan 1, 2003

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By T. W. Gonzales

The refractory performance of Peirce-Smith converters is considered to be mainly determined by effects of process control and refractory installation design. BHP Copper has shown that, over the last four years, considerable improvements in tuyere line life can be affected .by maintaining a uniform temperature in the operating converter and by ensuring sufficient and specific placement of expansion allowance in the construction of the refractory brickwork. A combination of optimized crane availability, rapid matte transfer, converter operating practices, new refractory installation techniques and applications has minimized out-of stack time. In addition, larger diameter tuyere pipes and hard piping have increased blowing rates and lowered cycle times, which has resulted in a tuyere line performance in excess of 62,500 tonnes of blister copper before maintenance is required. This paper discusses the refractory installation design changes that were made to increase tuyere line life.

Jan 1, 1999

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By Jan Petter Maehlen

Solid H-absorbing materials are in focus of ongoing R&D to offer viable solutions for the hydrogen storage and supply systems aimed on use of hydrogen as energy carrier for automotive transportation. Low operating pressures, combined with high gravimetric and volumetric efficiencies, together with fast kinetics of hydrogen release at ambient temperatures (providing conditions for a low energy loss due to decomposition), are the most important features of the ?ideal? H storage material. Hydrides of the light elements are the only possible candidates to build systems with an overall efficiency similar to those accommodating liquid or compressed (700 bar) hydrogen. One promising material from this point of view is aluminium trihydride, alane AlH3 with a gravimetric storage capacity of 10 wt.% H. This work was focused on studies of the crystal structure and thermal decomposition of alane by application of powder synchrotron X-Ray diffraction.

Jan 1, 2006

By Pinai Mungsantisuk

Keywords: Pd-Ni alloys, Pd-Fe alloys, Pd-Co alloys, Magnetostriction, Magnetic Properties The presence of congruent melting minima, the occurrence of ferromagnetic transition over a large composition range, and FCC type crystal structure make Pd-Ni, Pd-Co, and Pd-Fe based systems attractive candidates in our search for materials with no rare-earths, large low-field magnetostriction, and good mechanical properties. The presence of paramagnetic-ferromagnetic transition over a broad range of composition also provides opportunity for fundamental studies. In this work, we have examined the magnetic and magnetostrictive behavior of Pd-Ni, Pd-Co, and Pd-Fe alloys over the entire composition range. Alloy sample rods were prepared by arc melting and casting. X-ray diffractometer was used to obtain lattice parameter data. Magnetostriction was measured along the rod axis using strain gages. Magnetic properties were measured using a vibrating sample magnetometer.

Jan 1, 2005