Search Documents

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016

By Xinghua He, Shujing Zhu

"In this paper, the chemical composition, the content and the leachability of heavy metals in dredged sludge are tested and analyzed. It is shown that the leachability of Pb and Cr exceeds the leaching toxicity standard, and so the dredged sludge is considered as hazardous waste and must be solidified. The effect of solidifying the dredged sludge by the hydraulic ash-slag cementitious composites is studied, and it indicates that the heavy metals can be well immobilized if the mass fraction of the dredged sludge is appropriate. The heavy metals are immobilized within the hydraulic ash-slag cementitious composites hydration products through either physical fixation, substitution, deposition or adsorption mechanisms.IntroductionDredged sludge is classified as a hazardous waste because it usually contains concentrated heavy metals and chlorinated organic compounds, as well as soluble salts, and is also composed of very fine particles. Moreover, inorganic pollutants are typically associated with soluble compounds, which are, therefore, highly leachable from dredged sludge when dredged sludge is contacted by a liquid medium[l1. Thus, dredged sludge must be stabilized in order to reduce its environmental impact on the final disposal site. The frequent means of dredged sludge disposal used include(!) Chemical stabilization (2) acidic extractionChemical stabilization is translating mobile heavy metals into low dissolution and low toxicity form through chemical reaction. The commonly chemical medicaments are sodium hydroxide, soldium sulfide, thiourea, EDTA. But Zhao et al [ZJ found sodium hydroxide is not fit for Pb stabilization, the other three are effective, but the chemical properties of sodium sulfide are not stable, thiourea and EDTA are very expensive, and so it is very difficult to apply them. Moreover, because of the complexity of heavy metal conformation and dredged sludge composition, it is very difficult to find a cheap and prevalent stabilization medicament in point[31 ."

Jan 1, 2013

By Douglas K. Modrow

In the fall of 1993, construction was completed on a state of the art industrial waste water treatment plant at Asarco's East Helena Lead Smelter. Purpose of the plant was to remove arsenic and metals using hydroxide precipitation. Completing of the plant culminated a lengthy process of laboratory bench-scale test work, engineering, construction, and Environmental Protection Agency (EPA) oversight. Unfortunately, the effiuent requirements for the plant were made significantly more stringent as construction was rearing completion. As a result, optimization activities were initiated to determine and implement measures to substantially improve effiuent quality so the new discharge limits could be met. These activities consisted of acquiring a thorough understanding of process chemistry and plant operations, and developing simple, practical methods of automating unit operations associated with the treatment plant. Implementation of these modifications in the second half of 1996 will not only significantly improve the constancy and reliability of treatment plant operations, but also result in operating cost savings and reduced need for increased operator attention at capacity flows, plus allow the treatment plant to meet the new discharge limits.

Jan 1, 1996

By Asok Kumar Das

"In steel making ferroalloys occupies a commanding role for production of varied quality of steel. Ferroalloys enable alloying elements such as chromium, silicon, manganese, vanadium etc to be safely and economically introduced into metallurgical processes thus giving certain desirable properties of the alloyed metal. Their importance grew with the progress of the steel metallurgy which implied more diversified alloying elements, in better controlled quantities, in purer steel. The ferroalloy industry became a key supplier to the steel industry. Production of ferroalloys generally involves the use of Electric Arc furnace(EAF) into which raw materials(e.g. various metal ores, quartz, coke, lime etc ) with relatively fluctuating physical compositions are loaded. Due to this, one of the major environmental impacts of producing ferroalloys is the emission of dust and fume from the smelting process. INTRODUCTIONFerro Alloys are essential ingredients used for refining, de-oxidation, desulphurization and alloying addition in the production of different types of steel and hence Ferro Alloy industry forms a back bone of iron and steel in the world. Indian ferro alloy industry is more than 45 years old. It produces most of the bulk ferro alloys and a large number of special ferro alloys. The present installed capacity of the Indian ferro alloy industry is sufficient to meet the requirement of existing level of indigenous steel production of about 46 million tonnes. Revised National Steel Policy – 2008 envisages production of more than 100 million tonnes of steel by the year 2011-12, at proportionate annual growth rate per annum. The focus of the policy is to achieve global competitiveness not only in terms of cost, quality and product-mix but also in terms of global benchmarks of efficiency and productivity. In order to achieve the objectives of National Steel Policy and also to meet the requirement of ferro alloys, the Indian Ferro Alloy Industry has to gear up in terms of enhancement in production capacity, sourcing of raw materials, up gradation of technology, improvement in productivity, automation / mechanization, customer satisfaction etc."

Jan 1, 2008

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

By Dean G. Heitt

"The Rain and SMZ mines from 1987 to 1994 produced a total of22.0 t of gold from a pre-mine reserve of 14.24 Mt of ore grading 2.13 g/t Au.Gold at Rain is hosted within the basal portion of the Mississippian Webb Formation. ·Mineralization is closely tied to the Rain Fault which is interpreted to be the main feeder for the deposit. Multiple collapse and hydrothermal breccia events provided permeability for the mineralizing fluids in the otherwise unreactive siltstones. Major alteration events include: decalcification and dolomitization of the Devils Gate Limestone; and silicification, baritization, argillization and oxidation of the Webb Fm. Six ore types based on XRD and visual rock chip Jogging have been identified: siliceous ore containing >40% quartz and <30% barite; siliceous-baritic ore containing mostly silica but >30% barite; baritic ore containing >40% barite; argillaceous ore containing >40% total clays (including alunite); calcareous ore containing mostly calcite and dolomite; and carbonaceous ore which has significant pyrite and organic carbon. Metallurgical testing of the oxide leach grade ores found that recoveries, on -1.3 cm crushed material, were greater than 70%. Results also found that Rain ore has strong grind dependency due to silica encapsulation.The Rain leach pad was commissioned in 1988, and to date 9.3·Mt at an average grade of0.65 g/t Au have been placed. Life to date recovery, through December 1995, is approximately 51 %, for a total of3.87 t of gold produced. Two major factors have contributed to the low leach recoveries at Rain when compared with the metallurgical testing: 1) More argillaceous ore than expected was placed on the pad especially late in the mine life and 2) approximately 50% of the tons placed were run-of-mine with no agglomeration."

Jan 1, 1997

By J. Sofra

The quantity of copper produced by secondary material processing is increasing as metal producers look to cleaner and cheaper sources of copper. The need to smelt secondary copper more economically, to process a wide range of materials with large fluctuations in size and composition and to cope with the increasingly stringent environmental constraints have put considerable pressure on existing conventional secondary copper smelters. The Top Submerged Lance process, developed and commercialized by Ausmelt Ltd offers a low cost technology, which is particularly adapt at processing copper-bearing scrap and residues. The application of Ausmelt Technology to replace conventional secondary copper processing operations introduces potential for significant advantages in environmental performance, and improved process efficiencies through the use of cheaper hels and reductants, the high rate of metal recovery and the flexibility inherent in the technology to process various feed material types. The economical, process and environmental benefits of its application are highlighted for both the smelting and converting stages of copper production.

Jan 1, 1997

By Fei Ruan, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"Viscosity is an important physical parameter of slag in metallurgical processes. Most studies of aluminosilicate and aluminate systems assume that aluminum occurs in tetrahedral coordination. In this case, the O/Al value was utilized to describe the slag structure in terms of the network character of aluminosilicate and aluminate systems. Composition and viscosity data from the literature and the trends were analyzed according to the O/Al value and temperature. It is shown that the O/Al value explains the trends in more than ten systems, containing more than 200 data points. In aluminosilicate system, the trend that viscosity value changed with the O/Al value which implies that alumina works as network modifier such as basic oxides or works as network former. In aluminate system, irrespective of the system and temperature, viscosity decreased steadily when O/Al value increased.IntroductionMetallurgical slags, which are made of oxides and many also contain fluorides, play an important role in metallurgical processes such as iron making, steel making and secondary refining processes. Aluminosilicate slags are applied in a wide range in metallurgical processes. A polymerizing effect of the addition of aluminum and an association of aluminum with low-field strength cations is further supported by the physical variations in aluminosilicate and aluminate systems. The behavior of alumina in silicate melts has been studied by various authors [1-6]. It is generally accepted that Al2O3 is amphoteric [7] because Al3+ ions can behave in profoundly different ways in a silicate melt. When added to a pure silica melt, Al2O3 acted as a network modifier, breaking the bridging oxygen of the pure silica network, thereby decreasing the viscosity in a similar manner to other network modifiers, such as CaO, MgO etc. to form [1/2Ca (AlO4)]4- complexes. However, when added with alkali or alkali-earth metal oxides, some of the Al3+ ions assumed tetrahedral coordination and replaced Si in the liquid network, the missing charge was compensated by Me+ or Me2+ ions. Therefore Al2O3 acted as network former [8, 9]."

Jan 1, 2011

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By F. Tanaka

In April 1999, a two-year campaign of the Mitsubishi furnaces was achieved at Naoshima Smelter; the present one is expected to be extended much longer. An overview of basic technology for decreasing refractory wear in the Mitsubishi Process is presented. One of the main features of the process is the use of top blowing lance technology which has a different effect on the furnace refractory than other conventional processes. The refractory wear of concern is hearth wear caused by top blown powder injection, wear of the side wall caused by splashing droplets, and wear of the bath level refractories caused by surface waves of melts in the furnace. These have been systematically investigated for many years. This paper describes the results of various model tests and their application to practical furnace design and operation.

Jan 1, 1999

By Georgette Smits

The gun-sprayed refractory lining of electrothermal furnaces used for the manufacture of carbon disulphide from liquid sulphur and charcoal at between 800 and l000°C are severely attacked during the process. A mineralogical study of samples of eroded refractory material disclosed that carbon disulphide had penetrated the lining, causing the precipitation of sulphides and carbon, and the decomposition of mullite, a major constituent of the lining, to corundum and amorphous silica. Calcium, iron, titanium, and chromium are undesirable cations in a refractory that is used in furnaces for the production of carbon disulphide, since they react readily with this substance. A series of tests, in which samples were exposed to different amounts of carbon disulphide for various residence times and at different temperatures, was carried out with eight types of aluminosilicate-based castable and brick refractory materials, to compare their resistance to attack by carbon disulphide. Mineralogical investigation of the test cores showed that castable refractory materials are unsuitable for this type of process because of the presence of calcium aluminates and other impurities in the cement. Of all the refractories that were tested, a mullite brick of low porosity, containing a minimum amount of impurities, appeared to be the most suitable for use in this type of operation.

Jan 1, 1989

By Gregor Kücher

Lack of basic knowledge on the semi-direct recycling methods for hard metals hinders the application on an industrial scale. However, advantages like reduced expenses and lower environmental impact draw interest at future potentials. Consequently, this report aims to offer insight into the influence of varying bulky hard metal substrates during their lixiviation in acidic media with an oxidant. The statistical software Modde 11 assisted in the development of a design of experiments (DOE) for evaluation of the impact of average grain size, binder and tantalum carbide (TaC) content on the leaching characteristics. The other experimental parameters were constant. Among them were temperature, solution concentration and quantity, duration and substrate surface exposed to liquid volume. Eventually, prediction plots and factors of the computed model equation describe the effects of varying substrate qualities on leached binder metal and selectivity.

By B. Garcia-Egocheaga, J. Rutten, N. Goicoechea, U. Meurer, Mager K., W. Saage, Simonettim F.

Because of the increasing use of zinc as an active and passive anticorrosion agent for steel, leading to constantly growing return rates of galvanized steel components, especially through the automotive industry, major Electric Arc Furnace (EAF) flue dust amounts with higher zinc contents will accumulate in future. Landfilling of steel plant flue dusts is no longer allowable for ecological reasons. These dusts are classified as hazardous by law. Waelz technology is safe and reliable. The range .of treatable feed materials has been extended by process modifications and state-of-the-art offgas technology. Waelz oxide, the product, is delivered to metal smelters for zinc production and the byproduct, Waelz slag, can be used in road construction. Despite the fact that Waelz technology is among the best available techniques (BAT), it is continuously being optimized further with respect to energy input, product and offgas quality in order to comply with the ever more stringent environmental regulations. However, if these flue-dusts are treated, the loops between the steel and the zinc industry can be closed by reusing recovered zinc which in tum leads to savings in natural resources and a more reasonable use of landfills.

Jan 1, 2000

By Brian Patrick, Norman Bell, Mark Schoenfield, Thomas Weber, Dietrich Gross

"The reduction of carbon dioxide emissions and the resultant greenhouse gas affect is hampered by the fact that all fossil fuels contain copious quantities of carbon. Process tweaking can keep the amount of carbon dioxide to a minimum but cannot significantly reduce the amount of carbon dioxide generated. The very nature of utilizing fuels requires that they be burned to release the heat required for the various processes. Reduction of metal oxides to manufacture or modify pure metals, generation of power, transportation and many other forms of fuel usage result in much of the generation of man made carbon dioxide. Oxyfuel is a unique contributor to carbon dioxide emissions. While creating higher concentrations of carbon dioxide the total volume of carbon dioxide generated is reduced. This paper will examine the unique characteristics and potential of oxyfuel that make the generation of lower volumes of carbon dioxide possible.Nearly ten years ago a commercial application of oxy-fuel was installed at Jupiter Aluminum Company in Hammond, Indiana. This process was funded and developed by Dietrich Gross CEO. This aluminum remelt facility now runs completely on oxy-fuel and has continuously for over ten years. This has reduced the melt rates to as low as 750 BTU per pound in continuous melting periods."

Jan 1, 2009

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia&apos;s Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech&apos;s laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"In a typical year, approximately 1.7 million tons of residues and wastes are expected from Ajaokuta integrated steel plant, Nigeria. They will be generated mainly from sinter plant, blast furnace (BF), and basic oxygen furnace (BOF) operations and during rolling and finishing. The residues and wastes include slag, dust, sludge and slurries from gas cleaning, waste water, mill scales and other associated scraps. In this paper concepts for the utilization of residues and wastes in Ajaokuta Steel Plant where no reclamation routines have been provided for in the first and second phases of its project implementation is designed. The paper analyses the sources of the iron oxide wastes and evaluates the quantities expected from the main production facilities of the plant which include the two 312 m2 capacity sintering machines, the two 2000 m3 blast furnaces and two 130-T BOF (of the 2nd phase expansion of the Steel Plant). A reclamation routine designed for Ajaokuta residues and wastes is presented.IntroductionIn the steel industry, approximately 550kg of residues per ton of crude steel arise from the production processes and from pollution control facilities [1- 4]. These residues consist of slag, dusts and sludge, mill scale, spent pickle liquor, and other iron bearing materials. The main by – products generated in the steel industry are listed in Table I.Although major progress has been made in the recycling and use of some of these residues, particularly flue dust, blast furnace and steel making slag, yet a significant quantity are land filled or stockpiled. These unsightly stockpiles occupy valuable real estate and may become a source of environmental pollution if not otherwise disposed. In any case, the dumping option has become quite costly. For instance, one ton of iron ore costs between 28 and 34 US dollar, whereas as much as $20 per ton of steel produced is required to meet environmental compliance obligation in the USA [5, 6]."

Jan 1, 2008

By T. T. Chen, J. E. Dutrizac

Noranda Inc., CEZinc presently employs a cement-stabilization (jarofix) process to stabilize its jarosite residues for direct disposal. In this process, Portland cement partly decomposes Na-jarosite to form Ca6Fe2(SC>4)3(OH)i2.nH20, ferric hydroxide and sodium sulphate which further reacts to form gypsum; approximately one-third of the Na-jarosite reacts in the current commercial product. The cured jarofix products also contain minor amounts of various Ca-Al-Fe silicate-sulphate-hydrate phases and traces of calcite. Together with gypsum and a Ca-Fe sulphate phase, these species bond the various particles together, imparting mechanical strength and reducing the permeability. Water-soluble Zn and Mg are stabilized in the Ca-Al-Fe silicate-sulphate-hydrate phases. The freshly cured products usually contain small amounts of moisture and traces of residual Portland cement, which provides additional alkalinity for the neutralization of any residual acid species. Jarofix products stored for more than six years in the laboratory, after curing, are usually dry and exhibit the same micro-textures as those of the freshly cured products. However, the stored products are depleted in the Ca6Fe2(S04)3(OH)i2.nH20 and Portland cement phases, and are enriched in gypsum and calcite which reflects the highly alkaline environment of the jarofix products. The aged products also have increased amounts of the Ca-Al-Fe silicate-sulphate-hydrate phases which have elevated Zn and Mg contents. This implies a further immobilization of residual water-soluble Zn and Mg during stora

Jan 1, 2000

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996