Search Documents

By Raymond E. Healy

Mercurian e1ectrum (Au-Ag-Hg alloy) is the principal Au-bearing phase in the massive sulphide ores at Trout Lake, Manitoba. The average composition of this phase (in wt %) is 49.2 % Ag. 38.7 % Au and 11.0 % Hg, with ranges of 17.34 to 76.47 % Ag, 1.62 to 79.86 % Au and 1.29 to 30.87 % Hg. Compositional variation reflects solid solution in the a-phase of the Ag-Au-Hg system. Backscatter electron imagery reveals systematic zoning and suggests a general crystallization sequence from metamorphic pore fluids of progressively Ag-rich compositions. Investigation of the occurrence of gold in mill products demonstrates that mercurian electrum accounts for over 90 % of the Au in Trout Lake ore. I Invisible" gold in pyrite (x = 0.72 ppm Au) and arsenopyrite (x 30.2 ppm Au) is confirmed by SIMS analyses, and accounts for 7-10 % of the Au in the ore, and 35 % of the Au lost to the tailings. The remaining 65 % of the Au lost to the tailings consists principally of mercurian electrum locked with pyrite. No significant losses of mercurian electrum in the size range amenable to flotation and/or regrinding is indicated.

Jan 1, 1989

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998

By Jilai Xue, Shuming Huang, Zengie Wang

The corrosion behaviors of chrome corundum/magnesia in laterite nickel slag were investigated by static crucible method. The results show that the molten slag can penetrate into chrome corundum or magnesia which are used as lining materials in smelter furnace, and the corrosion can occur at the slag-refractory interface and the inner area of the refractories as well. Both the penetrated amount of slag and the penetration depth of Fe, Si increase with increasing FeO content (10–25 wt%) in slag. Such penetration in magnesia is stronger than that in chrome corundum under the same corrosion conditions, as more pores in magnesia may provide channels for slag penetration and corrosion product transportation. A damage of the refractory linings and short service life of smelter furnace may happen during metallurgical processing slag with high FeO content.

Mar 1, 2017

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Denis Legault, Ghyslain Dube, Ronald Morin, Jacques Bonneau, Daniel Guay, Keith Annett, Raymond Breault

"·The total recycling of all the constituents present in aluminum dross is now an industrial reality for Akan. This is made possible by the combination of two patented processes: the Alcan plasma dross treatment process, operating since 1990 at its Guillaume-Tremblay Works, and the calcium aluminate fabrication process, operating at AlumiCa's new plant in Thetford Mines. The latter process uses the total non-metallic content of the dross, thus rendering possible the complete recycling of aluminum dross.After describing the plasma dross treatment process, this paper will present the calcium aluminate fabrication process and how both processes contribute to close the recycling loop. The characteristics of Nova!™ by-product will also be described, as well as how they contribute to make a calcium aluminate with chemical and physical properties that are highly sought after. This calcium aluminate, produced by AlumiCa, is marketed under the trade name Kwikflux®. AlumiCa's total production is presently sold to a number of steel plants worldwide."

Jan 1, 2000

By Viktor. P. Popov, Oleksandr. V. Derev'yanko, Oleksandr. I. Raychenko

"This paper is devoted to scrutiny problem of obtaining electro-contacts by electro-discharge sintering technology. A new unconventional method of electro contacts production (on Aggraphite base) can yield essential optimization resource.Review of three electro-technological methods of processing contacts materials is presented:- using graphite powder cladded by Ag;- mixture of graphite powder(which is a non-cladded powder) with Ag powder and addition of Fe powder particles;- method of infiltration of melted Ag into graphite piece without deformation and rupture of object.This technological approach can give the possibility to increase of compression strength of electro-contacts materials up to 340 MPa and more under conditions of additional reinforcing components (for example, by Fe).IntroductionThe electric current can be an active ""participator"" of the powder metallurgy technology [l]. At the passage of electric current through powders or some powder mixtures the phenomena including phase transformations arise. Here such effects, which are observed in the Ag-graphite and Ag-Fe-graphite powder mixtures and in the pair Ag-porous graphite, are described.The Ag-graphite composition materials (CM) are used, for example, as electric contacts [2, 3]. Since a material being produced is destined for the contacts it is necessary to take into account the following aspects: commutating current, its character and voltage, active or reactive character of working load, geometrical dimensions of contacts, quantity and frequency of switching on and switching off, pressure on contacts, distance between contacts, method of arc control, surrounding medium, its content, pressure and temperature. Thus, these and, maybe, choice of some other circumstances influence design, materials and production technology of contacts. The range of problems concerned dictates such steps as alloying of contact materials, optimization of structure, selection of kind of graphite, its connection with metal [4-10]. It is expedient to recall the main procedures of the first stage of the conventional technology: dosage of the initial graphite powder and binder-phenolic resin plastic varnish (for example, Bakelite), mixing, densification, thermal treatment, crushing, grinding, sieving, drying, dosage of grained graphite, dosage of the initial silver powder, obtaining of the silver salt solution, settling of salt, filtration, washing, drying of the cladded graphite powder, thermal treatment, obtaining of the graphite powder of particles cladded by silver. The second stage of the convectional technology starts by obtaining of the cladded graphite powder and finishes by annealing of the pressed blanks (Fig. 1)."

Jan 1, 2004

By Feng-guang Li, Rui Guo, Ju Zhang

Cooling stave is one of the most important equipment of blast furnace for iron making. The heat transfer performance and service life of the cooling stave, to a large extent, determines the efficiency and economy of the iron making process. In this paper, a 3-D heat transfer model of cooling stave was founded by ANSYS based on FEM theory, and the heat transfer characteristics of cooling staves which were made of different materials (cast iron, cast steel and copper) were analyzed. Then, several suggestions on choosing material of cooling staves were given according to the calculation results and the actual working conditions of the cooling staves.

Mar 1, 2017

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By F. Kavicka

An original application of ANSYS simulated the forming of the temperature field of a massive casting from ductile cast-iron during the application various methods of its cooling using chills. The numerical model managed to optimize more than one method of cooling but, in addition to that, provided serious results for the successive model of structural and chemical heterogeneity, and so it also contributes to influencing the pouring structure. The file containing the acquired results from both models brings new and, simultaneously, remarkable findings of causal relationships between the structural and chemical heterogeneity and the local solidification time in any point of the casting. The determined relations therefore enable the prediction of the face density of the spheroids of graphite in dependence on the local solidification time. The calculated temperature field of 500x500x1000 mm casting of ductile cast-iron with various methods of cooling has successfully been compared with temperatures obtained experimentally. Acknowledgments. This analysis was conducted using a program devised within the framework of the GA CR projects (No.106/04/1334, No. 106/04/1006 and No. 106/04/094), of the COSTAPOMAT-OC526.10, MPO/FI-IM/021, EUREKA No.2716 COOP and KONTAKT 14/ 2005/06.

Jan 1, 2006

By O. Norman Lotter

There are many scales of innovation in the pursuit of concentrator performance improvement, including paradigm change, inventive change and incremental change. All are important, but the last is low risk, low cost and has a relatively high probability of success, given the right metallurgical skills. Seeking continuous improvement is also essential to ensure that performance does not decline over time due to ore type changes, personnel changes, equipment wear and other factors. When properly implemented, these small gains offer a very high rate of return for the project cost because they are made from marginal, not total, operating costs of the plant. To be effective this approach requires plant trials that use designed structure and appropriate statistics to test the observed differences arising from the old and new process treatments, be they a change in flotation reagent, in grind, pulp density, etc. However the pursuit of small but financially significant performance gains is often regarded as fruitless because of the range of variance in plant data, and the consequent difficulty of ‘proving’ that a benefit has been achieved. Opportunity for improvement is thus sometimes relegated to the realm of the impossible, or at best, treated with skepticism. Operations managers prefer to look for the larger gains, which are easier to demonstrate and prove. Unfortunately, these are seldom to be found; rather, a large gain can be more easily made by executing a series of small recovery improvements that are together equivalent to the ephemeral single large gain. In this paper we advocate a policy of continuing improvement driven by rigorous performance testing protocols and a formal ‘risk analysis’ approach to judging the efficacy of changes implemented in the plant. Following these simple procedures allows rational decisions to be made on the basis of quantifying risk and reward. In particular we consider the choice of hurdle rate for decision-making which best balances risk and reward. It is shown through case studies from actual industrial practice that this approach is practical and delivers significant financial value to the operation.

By Eoghan T. M Doyle

Oxide mixtures of nickel (NiO), cobalt (COO) and chromium (Cr203) were prepared with graphite in stoichiometric amounts and the powder mixtures were compacted to produce cylindrical pellets. The composition of chromium oxide in these mixtures were varied. Pressed pellets were reduced in a flowing stream of argon-4% hydrogen gas (500 ml/min). Both slow and rapid heating methods were adopted to raise the temperature of a pellet during reduction of oxides to form superalloy powder. The reduction temperature was varied between. 1523 and 1623K. The effect of heating rate and niobium oxide addition on the microstructure of the superalloy produced was studied by using ordinary light and scanning electron microscopes. New phases formed as a result of reduction were identified by X-ray powder diffraction technique. The mechanism of reduction of oxides together with the microstructure of NiCrCo alloy are discussed. The thermodynamics of formation of ternary alloy phase is elucidated on the basis of binary phase equilibria and Gibbs free energy of mixing data for the constituent alloy compositions.

Jan 1, 1992

By N. Y. Ma

Solid wastes produced in ironmaking and steelmaking off-gas cleaning systems often contain zinc. The zinc level in these solid wastes is generally too high to recycle the wastes for iron through blast furnaces, but too low to economically treat the wastes for zinc through zincrecovery facilities. The behavior, status, and distribution of zinc in the ironmaking and steelmaking off-gas cleaning systems have been analyzed from three aspects: thermodynamics of zinc condensation, oxidation and deposition, correlation of zinc concentration with particle size and density, and aerodynamics of dust particles in the off-gas cleaning systems. Theory and supporting data show that spontaneous separation of zinc from iron-bearing dust occurs in the ironmaking and steelmaking off-gas cleaning systems. Dry off-gas cleaning systems provide the most favorable conditions and environments for zinc to separate from the dust. If highefficiency dry separators were applied and appropriately arranged in the off-gas cleaning systems, zinc would be concentrated, and the majority of the solid wastes could be recycled for iron recovery through blast furnaces.

Jan 1, 2008

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Bin Xu, Qian Li, Xin Min, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The ringing characteristics of acid and alkaline iron ore pellets powder in kiln were studied by the thermodynamic calculation using software FactSage7.0, roasting experiments using briquetting method and analysis of SEM-EDS. The thermodynamic calculation demonstrated that liquid phase could be generated from alkaline pellets powder at a lower temperature and the amount of formed liquid phase was much more than that from acid pellets powder at the same temperature. Roasting experiments indicated that the compression strength of alkaline pellets powder briquettes were also higher than that of acid pellets powder briquettes. Additionally, the analysis of SEM-EDS suggested that the alkaline pellets powder briquette presented more liquid phase and a more compact structure comparing with the acid pellets powder briquette, which was consistent with the results of thermodynamic calculation and roasting experiments. Hence, in comparison with acid pellets powder, alkaline pellets powder is much easier to ring in the kiln.

Mar 1, 2017

By Biswadeep Saha, Meenakshisundaram Ramanathan, Chai Ren, Sivaraman Guruswamy

"Fe-Ga alloys have a large low-field magnetostriction and these alloys are attractive candidates in energy conversion and harvesting applications. Small additions of W also increase the magnetostriction of Fe. In this paper changes in magnetostriction by W substitution for Ga in various Fe-x at.% Ga alloys are presented. Fe-Ga-W single crystals were grown using vertical Bridgman Growth technique. [001]-orientated single crystal samples were prepared with faces within 1 degree off <100> orientation. The samples were annealed at 1150 °C in the alpha-phase region and water quenched. The magnetostriction coefficient (3/2)A-100 measurements were made on these Fe-Ga-W single crystals. The result on the effects of W substitution and annealing on the magnetostrictive behavior of these alloys are discussed.*Support of this work by NSF-DMR under the award DMR-0854166 is gratefully acknowledged.IntroductionMagnetostrictive materials changes their dimension exhibit reversible strains and changes in elastic properties in the presence of an applied magnetic field or the reciprocal effect of changes in the magnetic properties with the application of stress [IJ and are very important in sensor, actuator device, linear motor, magnetomechanical devices, microelectro- mechanical devices, active vibration dampening devices application areas. The discovery of an order of magnitude enhancement in the magnetostriction of Fe with Ga addition coupled with low saturation magnetic fields, and excellent mechanical properties opened up the possibility of obtaining larger magnetostriction values in other low-cost ductile a-Fe phase based alloys with alloying additives that are less expensive than rareearths such as Tb and Dy [2·4l_ The magnetostriction values observed in Fe-Ga single crystals are sensitive to thermal history and composition. The formation of second short range ordering phases and local defects inside crystal structure can also cause a dramatic change to this alloy's magnetostriction behavior [5-9l_"

Jan 1, 2012

By Issa S. AI-Kharusy

Oxidation/reduction (REDOX) alloy media, as used in wastewater treatment, is founded on the exchange of electrons. Because of this electron exchange, many contaminants are converted to harmless components which require no further treatment. Other types of contaminants are removed from the waste stream by electrochemically bonding to the alloy medium. This paper discusses the REDOX reactions, the role of the alloy medium in various treatment processes, and describes specific applications of REDOX alloy media for the removal and minimization of waste. The characteristics and handling of spent treatment media is also reviewed as a further consideration in waste minimization.

Jan 1, 1996

By O. C. Gaspar

The mineralogical and textural characteristics of the volcanogenic massive sulphide ores from the Aljustrel and Neves-Corvo deposits have been studied by ore microscopy techniques since 1977. Several ore types have been recognized, and the ore paragenesis, ore textures, and behaviours of different ore types during grinding and concentration processes, have been determined. An ore classification was established for use in metallogenetic studies, ore reserve calculations, selectivity during mining, and control of the ore beneficiation processes. In addition, an empirical method was developed for supplying, on time, the qualitative and semi-quantitative information needed for processing the Aljustrel ores and for optimizing the Neves-. Corvo copper and tin concentrators.

Jan 1, 1991