Search Documents

By D. E. Larson

In cooperation with the National Institute of Environmental Health Science and the National Institute for Occupational Safety and Health the U.S. Bureau of Mines conducted grinding research on non-asbestiform tremolite. The goal of this effort was to prepare ground tremolite samples containing a considerable percentage of acicular grains with aspect ratios (approximately = 8um long with widths = 1 um) similar to those of asbestos particles suspected of causing cancer, Optical-and electron-microscopic examinations were used to monitor the size and shape of the grains in the ground products. Although customized milling techniques do have noticeable effects in producing acicular grains, the prismatic nature of fracturing in the non-asbestiform tremolites limited the number of acicular grains that could be purposely produced, and indicates that the likelihood of high concentrations of acicular particles occurring under normal mining and milling conditions is small.

Jan 1, 1991

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

By Robert E. Moore

Renewed interest in olivine refractories has led to efforts to characterize them employing modern techniques of experimentation and data analysis. Initial studies have focused on determination of physical and thermophysical properties. Special equipment for the determination of thermal shock resistance and creep behavior have been constructed. Optimal compositions for maximizing various properties are being identified using appropriate statistical techniques. The overall goal is to develop response surfaces for each of a selected group of engineering design and use properties. Development of ?olivine Refractories? in the United States The term "olivine refractories" is used here because it does appear that domestic deposits of this rock will be the focus of renewed interest and "olivinell is the preferred term in this country. There are extensive deposits of high quality olivines extending through parts of Georgia. North Carolina and in the state of Washington. The eastern olivines are much more localized and extensively altered compared to the western materials. The Washington olivines exist as massive rock deposits in the Twin Sisters mountain area northeast of Seattle and their inaccessi-bility has slowed efforts to develop them. The North Carolina olivines have been used in steel plant applications since the 1930's. Geologists use the term "olivine" to describe assemblages of ortho-silicates. 2RO.SiO2, wherein the RO may be MgO. FeO. MnO. etc. When the RO consists essentlally of MgO and FeO. the material is called dunite and. as such, is synonymous with "refractory olivine." Refractory olivines utilizing North Carolina materials were developed for brick products by Birch and Harvey in this country around the mid-1930's. (I) Their work was completely independent of that of V. M. Goldschmidt and co-workers who used massive dunites located in Denmark. (2) These deposits are currently being mined by A/S Olivine of Denmark for the manufacture of a rather complete line of brick shapes for use in steel-plant. glassplant. and cement kiln applications. Birch and Goldschmidt

Jan 1, 1982

By John B. Cocanour

The U.S. Bureau of Mines (USBM) has developed a laboratory-scale on-line analysis and process control system for a decopperization electrolytic circuit. This system is software driven, running on a 486DX-33 personal computer (PC) utilizing a portable energy- dispersive x-ray fluorescence (XRF) spectrometer as the sample analyzer. The XRF copper reading obtained was used as the control variable through an RS-232 serial interface to the PC for software-based control of feed flowrates. When the copper concentration in the electrolytic cell (as measured by the XRF) deviated from the set point, the feed flowrate to the cell was automatically altered using software-based proportional-integral-differential (PID) computer control to yield the desired copper concentration at the electrolytic cell outlet.

Jan 1, 1994

By Byung-Su Kim

The recovery of elemental sulfur from sulfur dioxide has important implications for coal- burning power plants and nonferrous metal smelters. The thermodynamic analyses showed calcium sulfide to be suitable for recovering elemental sulfur from sulfur dioxide. At the temperatures of 1023 to 1153 K under the sulfur dioxide partial pressures of 5.0 - 60.1 kPa, elemental sulfur from sulfur dioxide was recovered by its reaction with calcium sulfide. The kinetics of this reaction were measured at the same conditions using a thermogravimetric analysis technique. This reaction scheme would be attractive if the coproduct calcium sulfate can be reduced to regenerate calcium sulfide. This is the topic of another paper. At 1073 K under the sulfur dioxide partial pressure of 25.8 kPa, 48 % of the original calcium sulfide was converted to calcium sulfate in an hour. Under the same conditions, 55 % of the regenerated calcium sulfide were converted to calcium sulfate in an hour even after third regeneration.

Jan 1, 1999

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By Nathaniel R. Quick

"Nd: YAG, KrF excimer, and Cu-vapor lasers are used in air to synthesize conductors and semiconductors as a second phase in silicon carbide and aluminum nitride. Conductor resistivities as low as 104 O-cm are formed in these substrates; the resistivities for the untreated substrates range from 10 11to 1014 O-cm. The silicon carbide conversion is relatively independent of wavelength while the aluminum nitride conversion shows a dependence on wavelength over the range 248 nm to 1064 nm. Silicon carbide conductors, evaluated over the range 15 K to greater than 300 K, exhibit metal like conductivity; resistivity increases with temperature. Silicon, carbon, and oxygen are identified as the principal chemical species associated with the conductor in SiC substrates while aluminum, nitrogen, and oxygen are identified as the principal chemical species associated with the conductor in aluminum nitride substrates. The silicon carbide system, which has the less complex phase diagram, is evaluated in more depth to explain the synthesis mechanism. Oxygen was principally on the surface and increasing SiC conductivity is associated with decreasing spacing between 5 µm, or less, diameter carbon globules. This technology is proposed as a replacement for metallization in electronic packages, sensors and devices. INTRODUCTIONCeramics are commonly used for multichip module, hybrid and multilayer electronic packaging; semiconductor device and sensor applications because of the insulating, conducting, semiconducting, or superconducting properties that these materials possess (1,2) The majority of ceramics, however, have not been known to exhibit conductive or semi conductive properties when exposed to rapid thermal heat processing. A ceramic and process which through selective conversion can combine two or more of these electrical properties to eliminate the need for metallization is of interest to both the commercial and military sectors."

Jan 1, 1994

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By M. -L. Metsärinta, J. Nyberg, A. Roine

The Kokkola roasting plant uses more than 20 different zinc concentrates every year. During recent years there has been an increase in the variation in concentrate quality; in particular, the amount of fine-grained and low-grade concentrates has increased. Therefore, a great deal of development work has been carried out to improve the operational flexibility, online availability, production capacity and calcine quality of the roasting plant. This work consisted of a heat and material balance model of the roasting based on HSC Chemistry software, a new water admixture system for the concentrate feed, a new oxygen feed system for the process air line, improved cooling of the furnace and boiler and improved operational practices, dust removal and concentrate mixing. These new process control tools and other improvements, as well as some test results, will be described in this paper. The oxygen feed may be used to improve production capacity and to decrease the sulfide content of the calcine. The water feed may be used with fine concentrates to decrease both dust carry-over and the temperature in the top part of the furnace. Improved cooling of the furnace and boiler helps to increase production capacity.

Jan 1, 2000

By Lv Guozhi, Niu Liping, Liu Yan, Zhao Qiuyue, He Jicheng, Zhang Ting’an, Dou Zhihe

"This paper proposed a new method of Mg and Cl2 circulating for titanium sponge production by direct pyrolysis and thermal reduction process. Effects of pyrolysis temperature, pyrolysis time and partial pressure of oxygen on pyrolysis efficiency were researched, and the crystallite structural transformation of MgO productions at different pyrolysis temperature and time were analyzed by XRD. The experimental results indicates that the pyrolysis temperature and time effects the pyrolysis efficiency obviously, and the reasonable pyrolysis conditions by using MgCl2 in molten state are as follows: the pyrolysis temperature is 1100?, pyrolysis time is 60min and the partial pressure of oxygen is 100%, the pyrolysis efficiency get above 95% at this conditions. The dynamic analysis of molten magnesium chloride pyrolysis reaction shows that, as a chemical reaction process control, the response of the apparent activation energy Ea=70.4 kJ/mol.IntroductionTitanium is a young metal, it is applied in industrial until the Second World War. It is 160 years from the discovery of titanium to the industrial production of ductility titanium by magnesium reduction method in the United States in 1948. As a new kind of metal, titanium and titanium material are better than the traditional metal materials in mechanical properties, heat resistance and thermal conductivity. Titanium is a kind of landmark structure and function material, which is called “space metal”, “Marine metal”, “Intelligent metal” [1-3]. Although the study of new methods of titanium melting get more at present, Kroll method and Hunter method are really applied to industrial production methods for titanium smelting, and Hunter method is already discontinued because of costs at present. The core technology in Kroll method of sponge titanium production process can be ome down to two circulation, namely the cycle of magnesium and chlorine in preparation-process of titanium sponge. In the traditional Kroll method, the cycle is realized through magnesium chloride which is produced by the electrolytic magnesium reduction process in hot molten state. But because investment of equipment for electrolysis method is too high, this method has not been used by most titanium sponge production enterprise in China. At present most titanium sponge production enterprise in China produce titanium sponge by the outsourcing of titanium tetrachloride, but the main disadvantage of this method is that the by-product of magnesium chloride is difficult to deal with."

Jan 1, 2012

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By Dominic T. Jordan, Quinn G. Reynolds, Christopher J. Hockaday, Ian J. Barker

A direct-current (DC) plasma arc furnace is a type of electric furnace used for metallurgical operations. The successful operation of DC furnaces depends to a large extent on gaining a fundamental understanding of the arc phenomenon itself, and ensuring its presence in the furnace at all times. A method for detection of the presence of the arc in a DC circuit is presented, along with discussion of why this may be of value for certain modes of furnace operation such as brush-arc. The theoretical development of the method is presented along with supporting experimental work conducted on large-scale pilot-plant facilities.

Jan 1, 2014

By den Bulck A. Van

In Europe, 50% of the copper originates from recycling. High-Cu containing scraps are regularly rich in impurities like Fe, Ni, Sn and Pb. Many high-Cu containing scraps are fed directly into anode-furnace casting installations or furnaces with limited refining capability. The impurities levels of the anodes produced in these processes should however remain acceptable for further electro-refining. The distribution of Sn between copper and slag has been investigated for conditions relevant to copper converting. Unlike previous studies, this work focuses on the behavior of Sn relevant to fire refining conditions, which are essential for anode refineries.In this study, liquid Cu–1Sn and CuOx–FeOy–SiO2 slag, with CaO additions, were equilibrated at 1300 °C in vacuum sealed SiO2 ampoules. After metal–slag equilibration, the samples were quenched in water. The composition of the slag and Cu metal was investigated with Electron Probe X-ray Microanalysis. The distribution coefficients of Sn between slag and Cu metal were determined as a function of slag composition.

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By Jan Dabrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures at each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 2D graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mu, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003