Search Documents

By S. C. Flood, J. D. Hunt

"The columnar-equiaxed transition (CET) has been studied numerically under unsteady-state conditions using mathematical models that: (i) include a non-equilibrium undercooling at the columnar front;and(ii) describe the simultaneous evolution of the columnar and equiaxed zones.The results are discussed and compared with those produced by a steady-state analysis.IntroductionThe majority of the previous work on the columnar-equiaxed transition (CET) has concentrated on the production of equiaxed nuclei, regarding this as being the critical step in the formation of an equiaxed zone. Recently, the growth of equiaxed grains has been considered and this is not unreasonable because, for an equiaxed zone to be present, the grains must grow as well as nucleate. Since the growth rate of the grains will be determined by the thermal environment at and ahead of the columnar tips, it was decided to model the liberation and flow of heat during solidification to discover whether the various trends in the columnar range might be explained by their effect on the temperature profile throughout the casting. The models presented here for the solidification of a casting are the first to include the latent heat liberated ahead of the columnar front. Burden and Hunt (1) consider its effect only qualitatively, and although Lipton et al (2) adopt a criterion for the CET which is based on the thermal interaction of the columnar and equiaxed grains, they do not actually include the latent heat in their calculations.It can be argued that the latent heat liberated by the equiaxed grains in the bulk will retard the columnar dendrites in a casting: once the equiaxed grains are sufficiently well-established, the latent heat that they evolve could slow down the columnar growth to such an extent that the equi axed would dominate. Alternatively, the latent heat produced by the equiaxed grains might suppress further equiaxed solidification by raising the bulk temperature. The nature of the thermal interaction between columnar and equiaxed growth is not obvious, and because it is dependent on the material parameters and the dimensions of the system, it cannot be considered effectively in a qualitative way but has to be studied quantitatively: hence the need for the mathematical models discussed in the following pages. The results of the models are discussed in the light of a steady state analysis."

Jan 1, 1986

By Robert S. Gärtner

The selective aluminum extraction by 3 different calixarenes (p-tert-butyl-calix[4]arene-tetra¬2-acetic-acid-ethyl-ester, p-tert-butyl-calix[4]arene-tetra-2-acetic-acid and p-tert-butyl-calix-[4]arene-di-2-acetic-acid-ethyl-ester) from an industrial pickling bath solution was studied. The pickling bath solution contained hydrofluoric and phosphoric acid as its main components. The aluminum removal was not successful and also no significant extraction of trace metals present was observed.

Jan 1, 1999

By P. N. Anyalebechi

Keywords: Aluminum alloy 3004, Solidification rate, Homogenization, Second phase particles The effects of the fineness of as-solidified cast microstructure and temperature on the response of aluminum alloy 3004 to homogenization heat treatment (a.k.a. preheat) have been investigated. The study was conducted at 538oC and 595oC on directionally solidified laboratory-size ingots with a range of solidification rate of 0.10oC/s to 29.4oC/s. Optical and electron microscopy, quantitative image analysis, electrical conductivity, and electron probe microanalysis were used to quantify the effects of the homogenization heat treatment on the microstructure of aluminum alloy 3004. In general, increase in fineness of as-cast microstructure and homogenization temperature enhances the a-transformation reaction, dissolution of Mg2Si, elimination of dendritic microsegregation, and dispersoid formation. The homogenization heat treatment reduces the average size of second phase particles in castings solidified at <1oC/s. However, in castings solidified at above 1oC /s, homogenization causes the coarsening of the second phase particles. Mn in solid solution is independent of homogenization heat treatment temperature.

Jan 1, 2005

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By D. J. Goodwill

BHP Copper operates a 3,400 tpd dry concentrate, single burner, Outokumpu flash smelting furnace (FSF) at their San Manuel copper smelter in Arizona. The very fine (-325 mesh), dry concentrate is fed to the burner from a 550 metric ton (nominal) capacity furnace feed bin via two drag chain feeders. During the 10-year history of the furnace, operations have been plagued by serious flooding problems. The fine concentrate sometimes becomes aerated during discharge from the bin and flows like a fluid at very high uncontrollable rates to the burner. This results in upset conditions at the concentrate burner leading to poor furnace metallurgy. This paper will examine the problems of uncontrolled feed from the furnace bin (i.e. flooding), and&apos; instantaneously feeding a flash smelting burner. It will show that a drag chain is a poor choice of feeder when high rates are needed, and that drag chains always produce a funnel flow pattern in a bin. BHP&apos;s drag chains cause narrow diameter, high velocity flow channels within the stored material. Consequently, there is insufficient residence: time for the concentrate to fully de-aerate before discharge, hence flooding occurs. In addition to the flooding problem, drag chains create a pulsating flow to the concentrate burner due to the tendency for material to slough off in discrete chunks at the discharge end of the slow moving chain conveyor. During the scheduled FSF rebuild in May 1999, BHP intends to remove the drag chains, modify the bin to a mass flow design and to use STAMET® multi-disc feeders to accurately and instantaneously control the rate of discharge from the bins. Air slides will be used&apos; to convey the concentrate to the burner.

Jan 1, 1999

By Rajashekhar Marti, York R. Smith

Lithium is anticipated to be a key, strategic material in the clean technology economy. The majority of lithium reserves are contained in continental brines and sea water (>60%). Currently the most economical approach to recover lithium from such resources is through selective adsorption. Spinel type lithium manganese oxide and lithium titanium oxide have demonstrated to be excellent candidate materials (after de-lithiation). However, due to the small size of the powders, they have limited industrial application and require immobilization. In this work, we examine the application of novel manganese oxide nanowire composites for the extraction of lithium from dilute solutions. Manganese oxide nanowires were synthesized and simultaneously immobilized on diatomaceous earth via hydrothermal method. Lithium manganese oxide were then formed by solid-state reaction, de-lithiated and tested for lithium ion adsorption.

Mar 1, 2018

By A. Dadgar

Extraction of gold and silver from two refractory concentrates using cyanide and bromine reagents was reported at the 12th International Precious Metal Conference (1). The objective of this paper is to present the gold extraction, recovery, and economics for two refractory concentrates using cyanide and bromine reagents. Gold extractions for cyanide leaching (24- 48 hours) and bromine leaching (6 hours) were the same and ranged from 94% to 96%. Gold recoveries from bromine pregnant solutions using carbon adsorption, ion exchange, solvent extraction, and zinc and aluminum precipitation methods, were better than 99.9%. A preliminary economic analysis indicates that chemical costs? for cyanidation and bromine process are $9.50 and $10.50, respectively per ton of calcine processed.

Jan 1, 1989

By I. Goy D. Gaballah

Decontamination of synthetic K2Cr2O 7 solutions containing 10 to 1000 ppm of hexavalent chromium using chemically treated barks have been studied at a laboratory scale. Metal removal from solutions depends on the pH, the initial concentration and the bark species. The use of a pulp density of 2 % in an agitated flask at the optimum pH for 2 hours leads to a percentage chromium removal of about 95 of the initial metallic ions content. Other trials conducted by column percolation permit the determination of the maximum retention capacity of the treated bark. Depending on the bark species, oak or pine, the rate of saturation is 110 and 215 mg of Cr per gram of bark respectively. The incineration of the metal charged barks gives recyclable, ashes containing 36 and 54 % of chromium metal for the oak and pine barks respectively. Experiments, of Cr6+ removal from industrial effluents containing up to 1800 ppm have been carried out on the semi-pilot plant scale. They have lead to the elimination of about 90 % of hexavalent chromium from this industrial waste solution. Further studies are conducted in order to define the hexavalent chromium binding mechanisms on bark constituents.

Jan 1, 1992

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By Batric Pesic

Dissolution of gold with elemental bromine was studied by using a rotating disc technique. The main parameters studied were: bromine concentration, stirring speed, pH, and temperature. Additionally, effect of copper, iron, and manganese was also examined. A special attention was paid to elucidate the role of cations, primarily Na+, during gold dissolution. It was found that gold dissolution with bromine was characterized with two pH regions. Below pH=7, gold dissolution was independent of pH, and above this value, gold dissolution decreased with pH increase. Gold dissolution rates were proportional with concentration of bromine. Two regions, diffusional and kinetic, were observed with respect to stirring speed. with respect to the role of Na+, and cations in general, they play absolutely no role during gold dissolution with bromine, unless they are in their lower oxidation state and become oxidized by bromine. In that case they have a negative effect because of bromine consumption.

Jan 1, 1991

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Jianguo Yin, Xuejiao Zhou, Xiaoyan Xiang, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade phosphorus-containing iron ore (LGPIO), a raw and wasted industrial solid material was used as an adsorbent to remove Cd(II) ion from wastewater. The effects of initial pH value, adsorptive time, initial Cd(II) ion concentration, adsorptive temperature and LGPIO dosage on the Cd(II) ion removal efficiency were studied. The results show that the Cd(II) ion removal efficiencies exceed 99.8% and Cd(II) ion concentrations are less than 0.10 mg/L under the pH value 6, temperature 20 °C, adsorptive time 90 min, initial Cd(II) ion concentration 50 mg/L, particle size <0.15 mm, adsorbent dosage 50 g/L and stirring speed 290 r/min. After Cd(II) ion removal reaction, the Cd(II) ion concentrations completely complies with the requirement of national discharge standard of water pollutants for cadmium and zinc industry (GB 20466-2010) (TCd(II) = 0.1 mg/L) in China. Therefore, it can be concluded that LGPIO is a new low-cost adsorbent which is suitable for the adsorption of Cd(II) ion from wastewater.

Mar 1, 2017

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By Fumiatsu Sato

In recent years, an increasing number of urban soil contamination cases have been found during redevelopment of former factory sites. Hydroclassification technique, separating heavily contaminated fine soil particles from contaminated sites, is one of the economical remediation techniques for contaminated soil by heavy metals, but the separated fine soil particles are generally landfilled because of the difficulty in removing strongly adsorbed heavy metals on them. In the previous study, the authors have investigated the mechanism and the optimum condition of chlorination-volatilization technique to eliminate heavy metals from inorganic waste and found it was needed to heat up around 1273K. In this paper, a new remediation technique for lead contaminated fine soil particles is proposed. This technique is composed of chlorination and subsequent warm water extraction. In the chlorination step, water-insoluble lead complex is chlorinated to be water-soluble lead chloride without volatilization, by heating the soils with MgCl2-CaCl2-KCl salt mixture at relatively low temperature. By subsequent warm water extraction, lead chloride is leached out. Effects of chlorination conditions, such as time, temperature, composition of the salt and added salt ratio, on lead behavior were investigated. It was proved that lead concentration could be reduced below Japanese environmental standard.

Jan 1, 2006

By Sue Xue, Carl C. Nesbitt

A project was completed which investigated the efficacy of recycling lead or lead monoxide from various fire assay wastes including crucibles, cupels and slag. The scope of the project was to determine optimal hydrometallurgical parameters so that direct separation and recovery of lead salts was economically feasible. A process was developed from the study which could use either acetic acid or nitric acid as a leachant, followed by several precipitation processes which could directly recover litharge (PbO) or other lead salts, such as lead carbonate or lead sulfate. The economics of the process is discussed. Analytical equipment such as the atomic absorption spectrophotometer and x-ray diffractometer supplied much of the information required for the study. However some novel analytical approaches using these instruments had to be developed to help in the determination of leaching kinetics and process quality control which are discussed.

Jan 1, 1999

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By Alan Branham

The Mike deposit is a large, low grade, oxide, gold-copper system found at the intersection of two major faults that bound the Carlin Window, Eureka County, Nevada. Disseminated gold occurs within metamorphosed and hydrothermally altered silty limestone (Silurian-Devonian Roberts Mountains Formation), beneath 182 m (600 feet) of barren Tertiary sediments and tuffs. A supergene copper oxide blanket occurs beneath and locally overlaps the lower portion of the gold zone. Decalcification argillization, silicification, and brecciation are superimposed on earlier calcsilicate hornfels and marbles. Altered dikes and sills intrude the gold zone and are locally auriferous.

Jan 1, 1995

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001