Search Documents

By Huai-ying Ma, Jun-hua Zhao, Xia Zhao, Si-bin Zhang, Wen Pan, Zhi-xing Zhao

Ignition is the start point of the sintering circuit, which plays an important role during the whole sintering process. The gas consumption accounts for 80% energy cost in the sintering ignition process. Therefore, gas flow reduction is of great significance to energy conservation in the sintering ignition process. In current study, the concept of comprehensive ignition intensity (CII) was introduced to determine the ignition effect. The experimental results indicate that the value of CII increases with higher air-fuel ratio at gas flow of 550 and 600 Nm3/h. From another point of view, given constant CII value, lower gas flow can be achieved with higher air-fuel ratio. Based on the comprehensive ignition intensity, the ignition parameters were optimized and the gas flow was subsequently reduced. By increasing the air-fuel from 5.5 to 6.6, the gas flow is reduced from 450 Nm3/h (8.1 GJ/h) to around 350 Nm3/h (6.3 GJ/h).

Mar 1, 2018

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By V. M. Sokolov, Jr. DuPlessis

The technology for recycling fine wastes, grinding sludges or swarf, and solids such as slag that contain a high content of metallic material needed improving. The objective was to produce a master alloy that met the tight requirements of the Western manufacturers and achieve improved yields of the valuable elements, nickel and cobalt, to over 90%. The alloys from the production of Alnico. magnets were chosen for this work. A process is proposed .that is able to recycle all kinds of Alnico wastes. This process is able to reduce all detrimental elements, which are contained in the wastes, to within acceptable levels. Molybdenum, if present, is an exception. Depending on the levels of contamination of undesirable elements different recycling strategies are proposed. The majority of the wastes can be recycled by melting and refining with a liquid slag layer using unique melting furnaces that are relatively unknown in Western nations. The proposed technologies allow the reelamation of over 95% of the cobalt and nickel from any kind of Alnico waste, and there are no limitations on the proportion of different kinds of wastes in the charge. The proposed processes and technologies could also be applied to the recycling of grindings, turnin

Jan 1, 2000

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By Zhihe Dou, Zimu Zhang, Guozhi Lv, Yan Liu, Xiaoli Jiang

"Cyclic heat stewed slag washing water carries high content of alkali and calcium and may cause serious tube scaling and impose an adverse impact on normal production. This study proposes a solution to utilize washing water by absorbing and mineralizing CO2, potentially restraining scaling and being able to create calcium carbonate powders. Effects of water flux on water quality, utilization ratio of CO2 and yield of calcium carbonate powder have been investigated; meanwhile, features of calcium carbonate powder are also represented. On the other hand, effects of factors such as as injection flux, pressure of CO2 on utilization ratio of CO2, morphology and purity of calcium carbonate are also investigated. The results show unambiguously that after soften injection of CO2, calcium ions were removed effectively via precipitation, alleviating the scaling problem. High purity yet fine carbonate powder could be achieved.IntroductionNowadays, 0.34 tons of blast furnace slags will be produced when producing 1 ton of pig iron; ensuing that, 0.12 tons of steel slag will be generated with 1 ton steel production while 1.57 billion tons of steel output all over the world in the year of 2012. It is therefore a critical issue to realize zero discharge of steel slags to achieve sustainable development and cyclic economy of iron and steel industry. In recent years, research institute of MCC and China JINGYE engineering company developed a heat stewed steel slag self-decomposition technology GENERATION III to solve the problem of instability of steel slags and realize the zero discharge. However, the problem of circulation line scaling which may cause the clogging, even exploding, need to be solved. The principles of the technology are: directly spraying water to the high temperature steel slag when it is poured into the hot closed pot, realizing the selfdecomposition via utilizing the waste heat of steel slag. The washing water is recycled to achieve a cyclic utilization. The process is shown in Figure 1."

Jan 1, 2014

By Pengqi Zhang, Mingcheng Bing, Lixiong Shao, Shuxing Qiu, Qingyun Zhang, Shengfu Zhang

Coal desulfurization has been regarded as an effective pretreatment for clean fuel and less environmental pollution. The microwave irradiation was used to desulfurize the Nantong coal leached with H2O2 and NaOH. The results showed the desulfurization rate of the coal is very low by directly microwave irradiation, while the coal samples leached with H2O2 and NaOH by microwave irradiation could effectively improve the desulfurization rate. The optimum desulfurization conditions were obtained as 10-min irradiation time, 800 W irradiation power, particle size below 74 μm, 1:1 concentration ratio of H2O2:NaOH, in which the desulfurization rate reached 51.14% of the total sulfur content. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra of coals structure before and after treatment have shown the bands in both coals changed slightly except the relative intensity of some absorption ones. It can be found that most of FeS2 and –S–S– functional groups transferred after treatment, while –SH and –S=O– had almost no changing by ATR-FTIR spectra analysis. The structures of coal matrix would not be broken by microwave irradiation in reasonable the reaction conditions.

Mar 1, 2017

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

In this study, Raman spectroscopy was utilized to investigate the evolution of char structure in pulverized coal (PC) during microwave irradiation. The results indicated that though microwave treatment was carried out at low powers of 132W or 264W, significant variation in char structure was still observed. Char structure turned out to be more irregular firstly under microwave irradiation. However, char structure of superior regularity was obtained with the extension of irradiation time. It can be conclude that short time microwave treatment may facilitate the chemical activity of coal, while long time microwave irradiation on PC may deteriorate its combustion or pyrolysis property.

Jan 1, 2016

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Lu-ming Zhao, Li Zhao, Yu Wang

In this paper, the change of crystallization rate, dendrite arm spacing and dendrite width of mold flux with various magnetic field conditions were studied by experiment. Having found that the crystallization ratio of mold flux increased from 33 to 96.6%, the dendrite arm spacing decreased from 72.47 to 38.02 lm, the dendrite width decreased from 48.47 to 27.02 lm while the magnetic field frequency (f) equaled to 8 Hz and its strength (B) increased from 0 to 30 mT. The crystallization ratio of the mold flux increased from 91.9 to 96.1%, the dendrite arm spacing decreased from 60.53 to 28.08 lm,the dendrite width decreased from 42.53 to 24.08 lm when B equaled to 20 mT and f increased from 6 to 12 Hz. However, the XRD analysis indicated that the phase types of the mold flux under the experimental conditions did not transform. Results showed that an alternating magnetic field can promote the crystallization of mold flux and refine grain structure.

Mar 1, 2018

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Danilo Marin Fermino, Ademar Benevolo Lugao, Nilton Lincopan, Luiz Gustavo Hiroki Komatsu

Polyethylene is widely used for packing applications. Different grades of polyethylene, LLDPE and LDPE play a major role in the film blowing industry. The use of nanoclay in polymer matrices (non-polar) requires the use of a compatibilizer agent, ethylene graft maleic anhydride copolymer (PE-g-MA), which acts as a bridge for nanoclay-matrix-interaction. In our study, blown films of LLDPE, LDPE, and their blends were produced using a twin screw extruder. The combination of PEs as matrix, montmorillonite (MMT) and silver nanoparticles (AgNPs) intended to improve mechanical and thermal properties. Nanocomposites films with 1 wt% of montmorillonite and 0.5–1.0 wt% silver nanoparticles were prepared by blow extrusion and evaluated. Nanoclay intercalation/exfoliation degree was investigated by X-ray diffraction spectroscopy (XRD) and scanning electron microscopy (SEM). Mechanical and thermal properties were evaluated. The results showed optimum dispersion at intercalation/exfoliation levels for polyethylene nanocomposite (PENC), slight increasing in mechanical and especially improvement in thermal properties.

Mar 1, 2017

By Mingmei Zhu, Lang Hu, Yu Wang, Hongpo Wang, Congjing Zhang

Magnetic field has a great effect on the crystallization behavior of mold flux and properties of the flux film between mold and strand, on which the surface quality of strand was deeply depended in continuous casting process. Therefore, studying the change law of the crystallization properties of mold flux in magnetic field is of great significant. In the present work, based on intensity of the applied magnetic field with the range from 0mT to 60mT, the crystallization ratio, crystal size and mineralogical phases of the flux film were discussed. The results show that crystallization ratio increases with the increasing magnetic field intensity, and the crystal size becomes bigger at the same time. The magnetic field promotes the crystallization ratio and growth speed of the crystallized grains of mold flux. However, magnetic field doesn’t change types of the mineralogical phases.

Jan 1, 2015

By De-wen He

The distribution of persistent organic pollutants in the environment is studied using the multimedia environmental fugacity model, and environmental health risk assessment of POPs nearby a copper smelt enterprise is carried out. The result indicates that all are in an agreeable risk level without exception. The annual individual chronic risk index of HCB is 7.50×10-11. The annual individual risk index of 3,3',4,4'-TCB is 1.57×10-9, and the annual individual risk index of 2,3,7,8-TCDD is 6.57×10-9.

Jan 1, 2009

By Shin-ya Kitamura

Kinetic modeling is very important to understand steelmaking reactions. The coupled reaction model proposed by Prof. D.G.C Robertson is the best suited program, and therefore, the author has applied it to the various steelmaking reactions, a few examples of which are discussed. Hot metal dephosphorization occurs under non-equilibrium conditions as it takes place between the slag, which has a high oxygen potential, and the hot metal, which has a low oxygen potential. A process simulation model based on the coupled reaction model was constructed. This model considers the solid and liquid slag, liquid metal phases, and the reaction between the solid and liquid slag, besides the reaction between the liquid slag and liquid metal. Using this model, the ruling factor to increase the reaction efficiency of dephosphorization has been verified. In the secondary refining process, the values of inclusion composition calculated by the thermodynamic model, under the assumption of equilibrium with the metal composition, were found to be different from those observed in practice. A kinetic model, incorporating the reactions between slag, metal, inclusion, and refractory has been postulated, and the composition change of inclusion during treatment has been analyzed.

Jan 1, 2014

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Cadmium and tellurium dissolution was achieved using hydrogen peroxide in dilute sulfuric acid. Leaching the scrap in 2.2 N H2SO4 yielded 99% Cd extraction and 98% Te extraction. Sulfur remained in the leach residue primarily in the elemental form. Elemental tellurium was precipitated from the leach liquor by adding Na2S2O5. Cadmium sulfate was recovered by evaporation. A preliminary process evaluation suggests that the process may have economic potential. Alternative recovery schemes are discussed.

Jan 1, 1995

By Hebi Yin

A two-dimensional multi-scale solidification model was developed to study the heat transfer, fluid flow, and grain growth occurring in the molten pool during the laser engineered net shaping (LENS) process. This model coupled the finite element method to calculate mass, energy and momentum transport in the macroscale with the cellular automaton technique to calculate liquid/solid phase change at the microscale. The validation of the model was performed by comparing the simulation results with experimental data from previously published works, showing good agreement in temperature distribution and the dendrite morphology (size and shape). The simulation results showed that Marangoni convection, caused by the temperature gradient along the pool surface, played a critical role in determining the flow pattern in the molten pool and exerted influence on the pool size and shape. It was also found that columnar dendrites can be formed, with dendrite arm spacings as fine as a few microns due to the high cooling rate during the LENS process. In addition, the influence of fluid flow on the dendrite growth in the pool was discussed.

Jan 1, 2010

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A PFS(polymeric ferric sulfate) coagulation-photocatalytic oxidation technology was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on TOC removal rate were investigated, and the results were compared with those of the common photocatalytic oxidation technology under the operating parameters of the photocatalytic oxidation defined. Single factor experimental results showed that TOC removal rate could reach 81%, when optimal operating conditions were as follows: TiO2 loading: 4.0g/L, irradiation time: 4h, initial pH is 5.1and PFS dosage:700mg/L. PFS coagulation and photocatalytic oxidation have synergistic effect, which is meaningful for highly efficient treatment of coking wastewater

Jan 1, 2015

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

By M. Olper

Today, copper production from direct leaching of oxidized copper ores followed by solvent extraction-electrowinning (SX-EW) accounts for about 15% of the total primary world output. SX-EW is a well-accepted process with an operating cost in the range 16-20 cents/lb. copper for small and medium size plants, depending on the plant size and local conditions. However, this technology presents some drawbacks that affect the operating cost and cause environmental concerns. ENGITEC and Paques Bio Systems have developed a new process that avoids the solvent extraction step and operates the copper electrowinning step at a lower cell voltage because of the depassivation of the anodic reaction. The consequence of this new concept is that the direct operating cost is in the range 10-12 cents/lb. copper. This new process is composed of the following steps: ? Selective precipitation of copper from leach solutions by biogenic H2S, yielding CuS and regenerating acid ? Leaching of the CuS with a ferric fluoborate solution to dissolve copper and produce elemental sulphur that is recycled back to the H2S biogeneration step ? Electrowinning of copper fluoborate solution in a diaphragm cell with the ECUPREX® Process, producing copper cathodes and regenerating the ferric fluoborate solution to be recycled back to the leaching step ? Biogeneration of H2S from the elemental: sulphur generated during the leaching step, with the nutrient source for the anaerobic bacteria selected form a wide range of organic substances and/or some industrial by-products containing carbon and hydrogen This paper describes all process steps with particular reference to the biological H2S generation technology. Also discussed' is the capability of the ECUPREX® Process to treat copper sulphide concentrates and copper matte.

Jan 1, 1999