Search Documents

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By I. D. Reznik

The flowsheets of converter matte production from sulphide copper - nickel and oxide nickel ores on Severonickel and Yuzhuralnickel integrated ,;corks are given. The cobalt behaviour in electrosmelting and autogenous ore smelting, converting and converter slag cleaning is observed. A list of acticles published in the 80 th is given.

Jan 1, 1993

By Kazuya Koyama

We are studying the hydrometallurgical recycling process of indium from an Indium-Tin-Oxide(ITO) target. For this process, it is necessary to remove Sn(IV) ions from the aqueous hydrochloric acid solutions containing In(III). In this study, the removal of Sn(IV) ions by a potentiostatic electrolysis method was examined. The polarization measurements and potentiostatic electrolyses were carried out under a nitrogen atmosphere. In the Sn(IV) solution, current begins to rise at the cathode potential of -0.26 V vs. SHE, and increases with a reduction in the cathode potential. In the In(III) solution, current begins to rise at a cathode potential of -0.43 V vs. SHE. Metallic tin was electrodeposited without indium electrodeposition at the cathode potentials of -0.30 and -0.40V vs. SHE. More than 98% of the Sn(IV) was removed at the cathode potential of -0.40 V after the electrolysis for 3hrs. Both tin and indium were electrodeposited at the cathode potential of -0.50V vs. SHE.

Jan 1, 2006

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Biserka Lucheva, Tzonio Tzonev

"Recycling of aluminum scrap and dross is significant in the economic and energy saving, as well as in the environmental protection. Recovery of metal aluminum depends on many factors. The aim of this work is to investigate experimentally the metal recovery under different conditions. The processing of aluminum dross was carried out in DC electric arc rotary furnace. The optimal technological parameters are determined. It is turned out that the presence of crushing refractory bodies during the processing of the aluminum dross in the rotary furnace increases the degree of aluminum recovery with about 10 %.IntroductionCompact and granular aluminum dross are used for the fulfillment of the experiments, which were obtained by salt free melting of aluminum scrap. The only preliminary preparation of the compact dross is crushing them into proper size, in compliance with the size of the opening for furnace charging and removing of fraction – 1 mm. The granular dross is subjected to sieving also with the purpose to remove the fraction – 1 mm. In these conditions the content of the metal phase in the compact dross is 72 %, and in the granular – 77 %. The processing of aluminum dross was carried out in DC electric arc rotary furnace (Figure 1).The purpose of this research is to investigate experimentally the metal recovery under different conditions and to establish the dominant factors, which need to be controlled."

Jan 1, 2008

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By P. Barrios

The copper refinery of Atlantic Copper was modernised and converted to the Isa permanent cathode system in 1995. The technology installed has proved to be an excellent platform for the development of operational improvements. During the years it has been working, the progressive assimilation of the new technology has been achieved and the level of operator knowledge has allowed design production to be reached and surpassed by more than 10%. At the same time, modifications to the work programmes, using existing equipment, have permitted the incorporation of new cells and the achievement of annual production levels of 250,000 tonnes and a productivity of 0.43 t/man-hour.

Jan 1, 1999

By Akihide Hosokawa

The void growth and coalescence in model materials involving a pre-existing three dimensional void array (i.e. multiple layers of a void array) was studied by X-ray computed tomography (XCT) coupled with in situ tensile deformation. To reduce the recording time, a new technique called fast tomography was employed. The model materials used in this paper were fabricated by the combination of an ultra-short pulsed laser machining system and a diffusion bonding technique, and two different types of arrays were prepared namely, FCC 1 and FCC 2 type array. This methodology allowed the authors to capture the entire process of growth and coalescence events of a void array embedded in the metal matrix. The failures in the both materials involved internal necking and shear localization. One of the highlights of this paper is that the plastic strain at the onset of void coalescence was measured for each model material. These values are in fact the adequate values to be compared with the coalescence strain predicted by existing void coalescence models such as the Brown and Embury model, the Thomason model and the Pardoen and Hutchinson model. The comparison suggested that the Brown and Embury model underestimated the coalescence in neither of the current model materials, while the Thomason model and the Pardoen and Hutchinson model showed a quite good agreement with the result for FCC 1 material. On the other hand the result from FCC 2 material agreed with none of the models probably due to the geometry of the void array that is not compatible with the existing models.

Jan 1, 2010

By Hongli Wen, Guangkun Shen, Qiong Deng, Shoujian Huang, Min Gan, Xiaohui Fan

"Due to the low iron grade and high sulfur content, pyrite cinder is difficult to be directly used for iron-making. In this paper, technology of magnetic roasting -grinding and magnetic separation -acid leaching was put forward for reclamation of pyrite cinder. For pyrite cinder of TFe53.51%, S2.20 %, studies showed that good magnetic effect can be achieved at roasting temperature 650~7000, reducing atmosphere CO/(CO + C02) 10~20% and roasting time 10~30 minutes. In separation conditions of grinding size -0.045mm accounting for 96.09% and magnetic field intensity of 1240 GS, iron concentrate of TFe64.81 %, S0.18% and iron recovery rate 91.44% was achieved. Acid leaching was studied to strengthen desulfurization. Results showed that high-quality iron ore concentrate of TFe66.3 l %, S0.10% was obtained under the conditions of hydrochloric acid mass fraction of 5%, pulp density of30%, leaching temperature of70? and leaching time of2 hours.IntroductionPyrite cinder is produced as a by-product of sulfuric acid industry [1] Domestic production is more than 12 million tons every year and occupied area is over 10 million square meters [2,3]. The pyrite cinder outdoor not only pollutes air but also damages surrounding surface [4] It after treatment used for iron-making is an ideal reclamation approach for its rich iron which is commonly 40-60% [5]. But pyrite cinder gets low utilization for its low iron grade and high sulfur content in China [6]. Therefore, comprehensive utilization of pyrite cinder has profound significance to environmental protection and the development of domestic iron and steel industry."

Jan 1, 2013

By Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao, Guojing Hu

"The equilibrium between titanium ions and metal titanium was investigated in fluoride-chloride molten salt. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The equilibrium constant of the equilibrium between titanium ions and metal Ti was calculated in KCI-NaCl- 2.5wt %K2 Tif 6 at the temperature of 1073K.IntroductionTitanium, the ninth most abundant element in the earth's crust, is endowed with high strength, low density, excellent flexibility, strong spring back characteristics, high-temperature performance, corrosion resistance and biocompatibility. These characteristics make titanium eminently suitable to be used in aerospace, marine industries, and harsh chemical environments. Although it has many excellent properties, the application of titanium in industry was limited by its high-cost. Therefore, many methods have been investigated for producing high-purity titanium at low cost. Electrolysis, involving the extraction and preparation of pure metal from ore using an electrolytic process, is considered a promising method for titanium metallurgy. Many studies have focused on the electrochemical behaviour and electrodeposition of titanium in molten chloride, fluoride, and chloride-fluoride electrolytes (1-IOJ. The electroreduction mechanism of Ti3+ ions in molten alkali chlorides has previously been studied by several workers. Two reduction steps, Ti3+ -Ti2+ -Ti, have been observed in various molten alkali chlorides [IJ. One reduction step, Ti3+ -Ti, has been observed in alkali fluoride molten salts l21. The behaviour of Ti4+ in fluoride or chloride-fluoride molten salts has also been investigated in the literature; it was proposed that the reduction of Ti4+ ions in the molten salts proceeded in a two step process: Ti4+-Ti3+-Ti l3l or a three step process: Ti4+ -Ti3+ -Ti2+-Ti ri. 4l Indeed, the stability of the titanium oxidation states depends on the bath composition l5l. The valence state was Ti2+ in alkali chloride melts, which was a lower oxidation state and correspondingly, in alkali fluoride melts, the higher oxidation states ofTi4+ and Til+ were more stable.The aim of the present work is to explore the effect of F/Cl atomic ratio on the equilibrium between titanium ions and metal titanium in fluoride-chloride at the temperature of 1073K. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The solubility product of the equilibrium between titanium ions and metal Ti was calculated."

Jan 1, 2012

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By Tom Lewis

This report discusses the evaluation of the ENVIRO-CLEAN PROCESS, a technology developed by Lewis Environmental Services, Inc. for the recovery of metals such as chromium, mercury, copper, cadmium, lead, and zinc from surface and groundwater streams. This new heavy metal removal process (patent-pending) utilizes granular activated carbon with a proprietary conditioning pretreatment to enhance heavy metal adsorption combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA limits. A 50 gpm system was installed for recovering hexavalent chromium from a ground water stream at a site located in Fresno, California. The effluent from the activated carbon system was reinjected into the ground water table with the hexavalent chromium concentration < 10 ppb. The system simultaniously removed trichloroethylene (TCE) to concentrations levels < 0.5 ppb. The activated carbon is regenerated off-site and the chromium electrolytically recovered. The full scale system has treated over 5 million gallons of ground water since installation.

Jan 1, 1996

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By Tang Chaobo

Employing manganese carbonate ore and zinc oxide dust as material, Mn-Zn compound oxide powder for soft magnetic ferrite was prepared by a serial methods, as follows: leaching by using sulfuric acid, removing aluminium and silicon by neutralization and flocculation method, using ammonium bicarbonate to co-precipitating Mn and Zn, calcinations and washing to removing impurity content. The optimal technical condition was obtained by experiments. The difficulty of removing impurity such as Si, Al, Ca, Mg, from leaching solution was solved. The impurity content in the production meets with the preparation standard of high quality soft magnetic ferrite. The compound oxide powder obtained in the experiment was made into lower power loss magnetic ferrite, the quality of magnetic ferrite meet the standard of PC40 which was established by TDK corporation.

Jan 1, 2006

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By John O. Burckle

For years, the measurement of fugitive emissions from the primary copper converter has defied all attempts based on inferential measurements, It has been concluded by virtually all investigators that the only dependable tech¬nique to measure these emissions would be to completely enclose an operating converter to permit the capture and measurement of all emissions. However, complete enclosure with a metal hood is difficult; many of the most serious fugitive emissions result during periods when the converter must be attended with crane-operated equipment. This approach would require either opening of the enclosure to permit the entry of large items of equipment or completely new methods for charging and tapping converters&apos; The installation of the air curtain hooding system at ASARCO&apos;s Tacoma smelter has permitted a quantitative approach to the direct measurement of the fugitive for the first time. In this program, the fugitives captured by the air curtain were measured at a downstream sampling point in the exhaust side of the air curtain system during the various portions of the converter cycle. Emission factors were established for sulfur dioxide, filterable particulate (method 5), inhalable particulate, and selected trace elements.

Jan 1, 1983