Search Documents

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By P. Lussiez

Precipitates consisting of amorphous ferrihydrite and crystalline goethite have been prepared by aging hydrolyzed Fe (III) solutions at room temperature. The precipitates have been characterized by x-ray diffraction and differential thermal analysis. The amorphous ferrihydrite transforms to goethite with time. The ferrihydrite to goethite transformation is affected by the presence of small amounts of copper or nickel coprecipitated with the iron. .The addition of copper decreases the amount of goethite at a given aging time and increases the amount of coprecipitate which is initially dissolved in sulfuric acid, but it does not seem to affect the dissolution of the crystalline part'. It is proposed that adsorption of copper hydroxo species on goethite nuclei delays the ferrihydrite to goethite transformation. The effect of nickel is less dramatic than that of copper. Apparently a portion of the added nickel is adsorbed on the goethite crystallite surface rather than incorporated into the goethite lattice.

Jan 1, 1981

By K. Yarnaguchi

In the Mitsubishi Continuous Copper Converting Furnace, calcium femte slag is used. Due to its extremely high basicity, the improvement of corrosion resistance of the refractory lining is in need. In order to clarify the corrosion mechanism and to search for a new corrosion resistant material, first, the surface snuctures of bricks corroded in molten slags were observed by EPMA. Second, the dissolution behaviors of sintered MgO-based pellets containing various oxide additives were examined. It was found that the formation and the dissolution of magnesiofemte at the surface of the bricks play an important role in their corrosion and an addition of NiO, Mn02, or Ti02 to MgO is effective in stabilizing the magnesio-femte and improving the corrosion resistance of MgO.

Jan 1, 1994

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Robert G. Telewiak

During the past few years, the international nickel industry has taken some important steps to respond to conditions of global production overcapacity, relatively flat demand and low prices. These include the implementation of major cost reduction programs by most producers, closure of some high cost operations and the establishment of the Nickel Development Institute. Consumption in the western world increased by about 7 per cent in 1987 compared to 1986, supplies were less than demand, inventories were low, and late in the year prices increased dramatically. By year-end 1987, most producers were operating at, or close to, their effective capacities. Nickel demand is expected to increase to the year 2000 at an annual rate of about 1.7 per cent, led by increasing usage in the stainless steel sector. If this rate of growth is realized, then there will be need for the effective capacity of the nickel industry to be increased. Producers in Canada have put considerable effort in the past few years into reducing costs - with impressive results. Mining costs, in particular, have been reduced dramatically. While production is still less than the peak years of the yearly 1970's, it has increased substantially from levels of the early 1980's. Over the next few years, production is expected to increase slowly. A key determinant of the level of production in the 1990's could be the effect that regulations on sulphur dioxide emissions have on limiting production.

Jan 1, 1988

By Xiang-yang Zhou

Keywords: Low-Grade Dolomite, Low CaO Content, High Specific Surface Area, MgO. A low energy consumption preparation technology of magnesium oxide with low calcium oxide content and high specific surface area from low-grade dolomite has been investigated. The optimum technical conditions for the preparation of magnesium oxide are the followings: dolomite is partially calcined at 750-800° for 2 h; the optimum solid-liquid ratio range in calcined dolomite slurry is 20-30 g?l?1; carbonation temperature, carbon dioxide pressure and end point pH value of carbonation are less than 40°, 0.4-0.6 MPa and 7 respectively during carbonation process; decomposition temperature of Mg(HCO3)2 solution is near 100°; calcination temperature of the precursor (i.e. precipitated basic magnesium carbonate) is less than 850°. More than 90% of magnesium can be extracted by the technology. The MgO product (CaO < 0.38%) with a specific surface area of near 50 m2?g?1 also can be obtained by the technology.

Jan 1, 2005

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By H. Kamiya, H. Hasegawa, M. Nojiri, S. Matsui, Y. Fukuda, M. Tsukada

"The present paper focuses on the action mechanism of anionic polymer dispersants in dense Si3N4 and SiC suspension. An atomic force microscope (AFM) was used to determine the relationship between the macroscopic suspension viscosity and the microscopic adsorbed structure of a polymer dispersant at the solid / liquid interface. The surface interactions within the suspensions were analyzed in various dispersant pH and additive conditions. The addition of an anionic polymer dispersant decreased Si3N4 and SiC suspension viscosity and increased electro-steric repulsion force on the non-oxide surface in solution at pH> 6 which was the isoelectric point of the materials. It was assumed that the increase of repulsive force was promoted by a hydrophobic adsorption of polymer dispersant on the non-oxide particles.IntroductionThe surface of silicon nitride and silicon carbide powders in a water suspension system has quite a complex molecular structure. In the case of Si3N4, hydroxyl and ammonium groups form on the surface and the pH of the suspension is increased from neutral to about 10 due to surface oxidation. The particle surface is negatively charged in alkaline solutions (pH=10), because the isoelectric point of silicon nitride exists in the pH range from 5 to 6. However, in spite of charging the negative surface charge, an anionic polymeric dispersant is generally used for the reduction in slurry viscosity.In dense SiC suspensions, an anionic polymer dispersant is generally used in order to disperse aggregates and reduce the suspension viscosity, too. Since an anionic dispersant is used in alkaline solutions higher than the isoelectric point of silicon carbide, the dispersant adsorbed on the negative charged surfaces of SiC.Few researchers have discussed and estimated the adsorption mechanism and structure of anionic polymeric dispersants on silicon nitride and silicon carbide surfaces. This is because it is difficult to observe the structure and measure the interaction at the solid/liquid interfuce directly. However, new developments in surface-force measurement technology have enabled the determination of non-DLVO type interaction for analyzing aggregation behavior2. The use of the AFM for analyzing the effects of various surfactants and co-polymers on colloidal dispersions and solid surfaces has also begun to rapidly expand to characterize the interaction between solid surfaces."

Jan 1, 2000

By Alysson Tadeu Pereira Almeida

Steels with low concentrations of nitrogen, hydrogen and carbon have been in large demand lately. The RH process is a secondary refining process that can simultaneously attain significant levels of removal of these interstitial elements from liquid steel. In the RH process, the melt circulation rate plays a very important role in determining the productivity of the equipment, since it affects the decarburization rate. In the present work, a physical model of a RH degasser in a 1:5 scale of an industrial reactor has been built and used in the study of the circulation rate and of the kinetics of decarburization. The effects of the gas flow rate and of the configurations of the nozzles used in the injection of the gas have been analyzed. The decarburization reaction of liquid steel was simulated using a reaction involving CO2 and caustic solutions. The concentration of CO2 in the solution was evaluated using pH measurements. The experimental results indicated that the kinetics of decarburization can be described by a first order equation. Based on the results, it was possible to determine the contributions of the decarburization in the upleg snorkel and in the vacuum vessel.

Jan 1, 2006

By Jean Frenay

Bacterial leaching tests have been carried out on Portugese pyritic ores containing zinc, copper, lead and silver as valuable elements. Both indigenous and isolated strains of Thiobacillus ferrooxidans were used. During the tests the factors pH, Eh and dissolved oxygen were measured and related to the leaching activity of the bacteria. Different means to estimate or determine the real bacteria concentration were examined. The influence of nutrient media and particle size has been evaluated. The role of galvanic couples was studied by electrical linking of mineralogical samples of pyrite, sphalerite and chalcopyrite. Leach residues were examined by optical microscopy to follow the mineralogical alterations during the leaching. The results show a rather good leaching of the sphalerite. However, the dissolution of copper from chalcopyrite is much more difficult, 50 % recovery never being obtained.

Jan 1, 1985

By M. Z. Mubarok

Effect of single addition of a lignin-based biopolymer additive, DP 2782, at various dosages as well as in combination with thiourea on cathode polarization during copper deposition was investigated by performing potentiodynamic and galvanostatic measurements using a potentiostat. The result of electrochemical measurements was compared with the behaviour of cathode deposition with glue and thiourea additives. Surface micro-appearance of the copper deposit after 1 h galvanostatic scan under current density of 330 A/m2 and various additive type and dosage was evaluated by scanning electron microscopy (SEM) examination. It was found that the addition of 2.5 mg/l biopolymer gave sufficiently polarizing effect of copper deposition. SEM examination of the cathode surface after galvanostatic scan revealed that the combination of the biopolymer with thiourea (2.5 and 3.5 mg/l) resulted in a compact deposit which is comparable with that resulted from the test with glue and thiourea.

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

By William R. Opie

Considerable effort by extractive metallurgical research organizations has been devoted recently to developing pollution-free processes for treating copper sulfide concentrates. A number of hydrometallurgical processes are in various stages of development and have been subjected to economic evaluation. Although the hydrometallurgical approaches eliminate SO2 emission problems, they create objectionable effluents and residues, make precious metals recovery complex, and are not very efficient for treating chalcopyrite. Furthermore, they are consumers of considerably more energy than pyrometallurgical processes which produce blister copper that can be electrorefined to commercial grade cathodes. This paper discusses a pyrometallurgical process under development by AMAX Base Metals Research & Development, Inc. (1) The original objectives set for the process development were: 1. Sulfur control of at least 95% with elimination of fugitive emissions. 2. Copper and precious metal recoveries as good as or better than conventional processes. 3. Low capital cost. 4. Competitive operating costs 5. Use of known proven technology where applicable.

Jan 1, 1976

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By B. J. Scheiner

The presence of organic materials in gold ores interferes with gold extraction by cyanidation. The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95%. This paper discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995