Search Documents

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge A. Soares Tenório

Mining of nickel ores generates large volumes of waste that must be removed in order to eliminate water contamination and reduce environmental impacts created by waste barriers. In this context, the need for innovations concerning the recovery of magnesium present in the liquor produced by the leaching of nickel laterite with sulfuric acid arises. Therefore, this work aims to develop a study regarding the crystallization of magnesium from a synthetic liquor solution using a batch autoclave system at high temperature. Agitation speed was kept constant at 1000 rpm throughout the 3 h of batch reaction for temperatures of 230 and 200 °C. Aliquots taken at each hour were analyzed by ion chromatography to measure magnesium concentration. The highest magnesium removal was observed for temperature 230 °C. X-ray diffraction (XRD) and scanning electron microscopy (EDS-SEM) analysis proved that the product formed was magnesium sulphate monohydrate crystals. Thermogravimetric analysis coupled with a mass spectrometer was used for the evaluation of the thermal stability of magnesium sulphate monohydrate. It was found that MgO and SO2 were formed by the decomposition of the salt at 1100 °C.

Mar 1, 2017

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By Ting Luo, Hongmin Zhu, Kai Huang, Shuanglong Du, Tao Gui, Yifan Xiu

"Poplar cotton, a cellulosic material, was found to adsorb metals ions effectively. In the present study, the biosorption characteristics of Pb(II) onto poplar cotton, were evaluated as a function of pH, contact time, biomass dosage, initial concentration and temperature. Within the pH range investigated (1.0-6.0), the optimal pH value suitable for the uptake of Pb(II) was determined. The maximum adsorption capacity obtained from the Langmuir model is around 0.52mol kg for the poplar cotton sorbent. Equilibration is achieved in 60min for the studied concentrations. Results suggest that the poplar cotton can be directly used as an effective and low-cost biosorbent for removal of Pb(II) from aqueous solution.IntroductionHigh value utilization of various biowastes produced in agricultural, forestry, fishing industries, etc. have attracted great interest from many researchers [1], Biomass, due to its easy availability, great abundance, low cost, easy processing, eco-friendliness and biodegradability, has exhibited exciting potential for being used as raw materials for the preparation of many new hi-tech functional products [2]. For example, using biowastes to synthesize sorbents for application in the removal of toxic substances such as dyes [3], heavy metals from the waste water [4] or in the recovery of valuable metals [5] from the ore tailings and secondary metals resources has made great progress in last decade. In present study, poplar cotton, a kind of white light fluff of poplar trees, like that of dandelion, usually flying in the air each spring was tested as a biosorbent for the remove lead ions from the water. It may also provide some good ideas for new sorbent design. Lead, as one of the typical poisonous heavy metals, for its typical toxicity and extensive pollution, was chosen to test the adsorption behavior of poplar cotton in aqueous solutions."

Jan 1, 2012

By Motang Tang, Chaobo Tang, Shenghai Yang, Lulu Guo, Yun Li, Yongming Chen, Jing He

A new innovative process for one-step and cleaner extraction of lead from spent lead-acid battery by reductive sulfur-fixing smelting was presented. This paper summarized and discussed several potential sulfur-fixing agents and molten salts which can be used in this new technique. Thermodynamic analysis involving reaction mechanism, ΔGT and predominance-area diagrams of different smelting systems were performed, respectively. The results proved the technical feasibility and high-efficiency of this process. Copper oxide ash (CuO), zinc oxide ash (ZnO) and iron oxide bearing residues (FexOy) can be used as sulfur-fixing agent to extract lead through exchange reactions. Sulfur-fixed efficiency of CuO, ZnO and FeO decrease slightly in turn. Sulfur contained in PbSO4 is fixed in form of Cu2S, ZnS and FeS respectively which avoids SO2 emission. The addition of molten salt can significantly decrease temperature of reductive sulfur-fixing reactions. Molten salt can be regenerated and recycled in smelting system after filtering solid residues.

Mar 1, 2017

By Qiu Dingfan

The Slurry Electrowinning Process (SEP) is a new hydrometallurgical method and clean technology, Sulfide ores can be treated by the SEP without S02 emission and the sulfur from the sulfides can be recovered in element form which is easy to stockpile and can be transported at low cost. In a special slurry electrowinning cell one can achieve at the same time the leaching of elements from the feed and the electrowinning of metals from the electrolyte, Because the anode reactions are utilized for leaching of some elements the consumption of the energy is decreased, SEP also has the advantage of separation some elements, It is especially suitable for treatment of complex concentrates containing Pb, Cu, Au, Ag and S, which could hardly be accepted by any smelter. In this work, the behavior of different metals in this process has been studied and it was found that the separation of metals in some minerals is possible through the SEP, Beijing General Research Institute of Mining and Metallurgy (BGRIMM) has studied the possibility of the SEP to treat bismuth concentrates containing S, Be and F in laboratory and pilot-test scale as well as in commercial plants, The commercial plant was set up in 1997, It has been in operation since that time, According to the results of laboratory experiments and pilot- plant test, a new plant to treat complex gold minerals was set up in 1998 and is in operation in 1999

Jan 1, 2003

By He De-wen

The increasing population and living standard in urban areas, have been accompanied with the growing quantity and composition complexity of rubbish, which are causing well-known social effects of pollution, while rubbish (solid waste) is a recyclable resource. To convert rubbish into useful materials, the essential measure is to carry out sorted collection of rubbish. The preconditions of implementing sorted collection are presented in the paper. 1 Characteristics of rubbish composition and amounts of recyclable contents are basic condition to implement sorted collection. 2 The existing available technologies of recycling, economic benefit from recycling, and disposal scheme of residual rubbish are restrained condition for sorted collection. 3 Public understanding and support to sorted collection are the key to success. 4 The government policies to be favorable for sorted collection is the pledge of success. 5 The establishment of a steady solid waste recycling market is also a guarantee to implement sorted collection continuously. 6 To establish management system of rubbish recycling as soon as possible. Further, the methods and procedure of sorted collection are discussed in detail and beneficial comments and theoretical basis to promote sorted collection of rubbish in urban area are presented; it will contribute reference value to municipal solid waste management.

Jan 1, 2006

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By Chao Zhang, Kexin Jiao, Yi Qian, Jianliang Zhang

Now low-grade iron ore were widely used. However, one prominent problem is that the content of trace elements is higher than that in high quality iron ore. For the requirement of the content of Mn, Cr, Ni, Cu, and Ti in hot-rolled steel sheet and strip, the upper limits of these elements in sinter will be studied in this paper. Using the activity model of aggregation of electronic phased slag composition, the distribution ratio of each element in converter is analyzed and the content of each element in hot metal is calculated. Furthermore, through the thermodynamics method, the distribution ratio of each element in BF is analyzed and the content of each element in raw material is calculated. The upper limits of Mn, Cr, Ni, Cu, and Ti in sinter can be determined by calculating, the values are as follows: Mn 0.767%; Cr 0.552%; Ni 0.055%; Cu 0.159%; Ti 0.108%.

Jan 1, 2015

By Keri Ledford, Stephanie Lin, Jason Nadler

Novel processes are being developed to fabricate thin copper thermal wick samples of a targeted porous microstructure. Structures of desired porosity, thisckness and pore size and distribution are achieved by tayloring the incorporation of sacrificial polymer beads in to slurry precursors. The thickness of the final structure is dictated by precisely controllable slurry application methods, such as spin coating. Ina subsequent heat treatment, th epolymer components thermally decompose and the remaining copper particles sinter to form a reticulated foam. The resulting microstructures are characterized in terms of porosity, permeability and specific surface area.

Jan 1, 2012

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By J. C. Riani

The release of heavy metals into the environment is increasing among others due to human activities such paint and pigment industries, tanneries, and metal finishing industries. Among metal releases, chromium is notable because this metal is carcinogenic. Thus, the aim of this work is to use an ion exchange system composed of one cationic resin column and one anionic resin column in order to adsorb the chromium (III, VI) from chromium electroplating effluents with the objective of recycling the water. The methodology consists of chromium adsorption tests using the ion exchange resins system with Purolite the 850 (polystyrene matrix, functional group quaternary amine) and Purolite C 150 (polystyrene matrix, functional group sulfonic acid). The contaminated solutions were passed through the columns with the assistance of peristaltic pump. Samples of the outgoing solution were taken in order to control the conductivity and pH and analyze the metals. The effects of the feeding outflow on the chromium adsorption were evaluated. The results show that the quality of the water collected at the end of the process is within the Brazilian standards about the discarding of toxic substances in the environment (CONAMA 357/05). This makes possible the recycling of water into the process and also its discharge in the rivers.

Jan 1, 2006

By Patrick R. Taylor

Titanium nitride has been synthesized in a thermal plasma reactor from ilmenite ore concentrate using methane and ammonia as the reactive gases. The product has been characterized by x-ray diffraction and SEM. Results show that a high concentration of methane favors the formation of iron, titanium nitride and titanium carbonitride. The formation of titanium carbonitride can be minimized by controlling the concentration of methane. The formation of TiN proceeds by the progressive reduction of the oxides of titanium to titanium, which is converted to titanium nitride.

Jan 1, 1998

By Martin Reyes, Juan Hernández, Julio Cesar Juárez, Isauro Rivera, Ma. de los Ángeles Hernández, Francisco Patiño

The dissolution of Ag contained in metallurgical tailings was studied by adding ions Cu2+ and Zn2+ in S2O3 2- medium. Chemical analysis of mine tailings by cupellation revealed a Ag concentration of 71 g/ton. The XRF and XRD analysis confirmed the preponderance of SiO2 in the mineral matrix. The experimental dissolution process was conducted in alkaline solution using six concentrations of NaOH and five of S2O3 2-, at different temperatures, also using five concentrations of Cu2+ and Zn2+ as a catalyst. The results showed similar values for both systems (96.8% and 97.13%). The ion Cu2+ and Zn2+ increases the dissolution of Ag, and decrease the reaction time of dissolution. Under the conditions used, pH and stirring rate did not affect the dissolution of Ag.

Jan 1, 2015

By R. Padilla

The reaction of chalcopyrite with gaseous sulfur has been investigated in the range 350-450 °C in order to transform this mineral into a more acid soluble copper sulfide and insoluble iron sulfide. The results of thermodynamic analysis of this system as well as the X-ray diffraction analysis of the reaction products showed that in the temperature range 350 400°C the sulfidation reaction proceeded without formation of intermediate copper-iron sulfides according to: The effects of temperature and time on the conversion of chalcopyrite were studied. Conversion of chalcopyrite reached about 80% very rapidly with increase in temperature up to about 400°C. The recovery of copper from the sulfidized samples was determined by leaching in oxygenated 1.2M H2S04, 2M NaCI solution. Copper recoveries over 90 % were obtained from samples sulfidized for 30 min at temperatures lower than 400°C.

Jan 1, 2001

By Zemin Ma

A novel chromate [Cr(VI)] reducing bacterium was isolated from chromite ore processing residue disposal site of China and identified as a Leucobacter sp. by 16S rRNA gene sequence homology. The minimum inhibitory concentration of strain CRB1 was 820 mg l-1 of Cr(VI). The reduction of Cr(VI) occurred only under aerobic conditions. With an initial concentration of 2.5×108 cells ml-1, 1800 mg l-1 of Cr(VI) was reduced entirely within 38 h under the optimum conditions, at 30 °C and pH 9.0. Increasing Cr(VI) concentrations prolonged reduction process and higher cell densities meant quicker reduction. A blue precipitate was produced during chromate reduction of strain CRB1, which was binding to the surface of bacterial cells and determined as trivalent chromium with electron paramagnetic resonance (EPR) spectrometry. The conspicuous chromate reduction ability of Leucobacter sp. CRB1 suggested a potential for bioremediation of Cr(VI) containing wastes.

Jan 1, 2008

By Riyad N. Ahmad-Bita, Shadia J. Ikhmayies

"SnO2:F/CdS:In structures were prepared by the spray pyrolysis technique on glass substrates at a substrate temperature Ts = 450°C. NH4F and HF were both tried as the sources of fluorine in the precursor solution of SnO2:F. A comparison between the properties of structures obtained by using the two doping compounds was performed. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to characterize the films. The structures prepared by using HF as a fluorine source were found to have more ordered crystal growth, larger grain size and sharper absorption edge. From the inspection of the first derivative of the absorbance it is expected that more interdiffusion on the SnO2:F/CdS:In interface takes place in the structures made by using HF. These results confirm that these films are better as forecontacts for CdS/CdTe solar cells.IntroductionThin film CdS/CdTe solar cells built in the superstrate geometry rely on transparent conducting oxides (TCOs) to make the front contact The investigation of combined CdS-TCO films has recently been developed owing to the great interest of better understanding the effect of these bilayers on the absorbers [1]. Usually SnO2 is utilized as a front contact for these solar cells. Optimizing the properties of the SnO2/CdS structures is an important step on the way to get high performance CdS/CdTe solar cells.There are different methods to prepare SnOz thin films, such as reactive sputtering [2], evaporation [3], chemical vapour deposition [3, 4], dip coating [5] and spray pyrolysis [6-9]. At the same time CdS thin films can be prepared by different techniques such as chemical bath deposition [10], thermal evaporation [11], screen printing [12] and spray pyrolysis [7, 13]. However, the spray pyrolysis technique is a very low cost and simple technique that enables intentional doping and getting large area and uniform thin films [14]. For these reasons it is choused to prepare SnOz and CdS thin films in this work. To improve the properties of these compound semiconductors, SnOz was doped with fluorine and CdS was doped with indium where such doping is well known for these compounds."

Jan 1, 2012

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By D. Tait, M. A. Halim, V. I. Lakshmanan, R. Sridhar

Rare earth elements (REEs), nickel and cobalt find their use in developing strategic materials and their demand is consistently increasing in the world while the extractable ores of these metals are gradually depleting. Process Research ORTECH Inc. (PRO) has developed innovative mixed chloride leaching processes for the recovery of REEs from alumino-silicate ores, and nickel and cobalt from laterite ores. The addition of magnesium chloride in hydrochloric acid enhances the activity of the hydrogen ion by orders of magnitude, which permit rapid leaching rates at moderate temperature and atmospheric pressure, along with high metal recovery. Innovative solvent extraction process steps are used for the separation of these metals from pregnant leach solutions. PRO’s processes also produce value added by-product of high purity iron oxide and recycle chloride lixiviant to the leaching stage. This paper describes the leaching and separation reaction mechanisms and potential process flowsheets.

Mar 1, 2017