Search Documents

By LuisW. Pommier

The industrial wastes generated by the plating industry, the circuit board manufacturing industries and other related industries normally contain high concentrations of metals, which make them hazardous. The extraction of the contained metals and their separation may be achieved by both pyro and hydro metallurgical processes. Some of the industrial wastes, those rich in some metals like nickel for instance, are being treated like mine ore concentrates and are being fed to smelting furnaces. The slags from these smelter operations are hazardous. They have, however, special environmental dispensations issued by the regulatory authorities. Hydro-metallurflcal processes have been reported. They also generate a residue which is hazardous because not all the valuable metals are leached out and also, because "non valuable" components, like chromium, are less readily leached. Residues from the plating industry, containing nickel, copper. zinc, iron and chromium as the major constituents and also sodium and calcium, together with cadmium, cobalt, lead. manganese, magnesium, molybdenum, and potassium, have been processed for the extraction of the valuable components. The generation of electrolytic nickel, copper and zinc and also of ferric chloride and chromium oxide is reported. The operation is achieved by a caustic leach for the extraction of zinc, followed by a sulfuric acid leach for the extraction of nickel and copper. This acid leach also extracts the iron and some chromium. The nickel copper and zinc are rendered pure by electrolysis, the iron is oxidized for the production of ferric chloride and the chromium is recovered as an oxide. The leaching operation is performed in two stages, first at a pH of 2.5 to generate an electrolyte for the partial recovery of the metals and then at a pH of 0.5 for the complete extraction of the metals. This leaching operation generates a residue, which although small in volume compared to the initial feed, still contains traces of the valuable metals and a portion of the chromium which makes it hazardous. Additional leaching with hydrochloric acid or nitric acid is required for its complete dissolution. The other minor constituents mentioned are present in concentrations each of less than 0.1% and are handled as impurities in the process. The metals which are soluble at a pH 0.5 and precipitate between 0.5 and 2.0 are bled off. Other impurities will concentrate on the raffinate from the solvent extraction operations from whence they are bled off. These bleeding streams are hazardous and the "impurity metals" are now present in concentrations which would make them valuable, however, the size of these streams is so small that they do not warrant their processing, however they could be marketed to specialized smelters. The extraction of the valuable metals, of the hazardous constituents, the generation of a marketable mixture of minor constituents and the production of a non-hazardous residue for declassification is profitably achieved.

Jan 1, 1998

By Niander A. Cerqueira, Pâmela Berçot, Afonso G. Azevedo, Victor B. Souza, Victor T. Bartolazzi, Bruno Padilha

In recent years, concern about environmental issues has become a parameter to consider in the projects in engineering. In order to reduce the impact that the tire improper disposal may result for the environment, we sought a solution to this problem. This article proposes the use of rubber scrap tires as fine aggregate in concrete production. The material produced was analyzed by a bending test, resulting in product quality, in particular for application in situations requiring a more ductile material.

Mar 1, 2017

By Irina V. Sokol

Alloyed steel chips and swarf formed during metal processing are looked upon as additional raw material In metallurgycal production. The manuscript presents some new methods for steel waste chips and swarf cleaning. One of them Is swarf and steel chips cleaning In ethylene tetrachloride with ultrasonic assistance and following, solvent regeneration. Thermal cleaning of waste chips and swarf provides exit gas products utilization. Catalyst Influence of metal surface on the process of thermal decomposition of liquid hydrocarbons during cleaning process has been studied. It has been our experience that the efficiency of metal waste cleaning technique depends on the storage time of the swarf. Waste chips and swarf cleaning procedures presented in the manuscript have been proved economically advantageous and environmentally appropriate.

Jan 1, 1995

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999

By Jannette L. Chorney, Katie J. Schumacher, Katelyn M. Lyons, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating a new method of extracting and refining rare earth elements (REEs) from mineral ores and concentrates. The relative stabilities of various REE compounds and differences in vapor pressures are exploited to selectively separate rare earth chlorides, with dysprosium and europium chlorides used as proof-of-concept experimental materials.

Mar 1, 2017

By John M. Gaines

Lead concentrates from the Viburnum Trend in Southeast Missouri are sintered, prior to smelting, to bind the particles together, homogenize the feed, and reduce the sulfur content. About 20% of the sinter at some plants is classified as bad sinter. A total of 130 samples of good and bad sinters were studied by reflected light microscopy, scanning electron microscopy-energy dispersive analysis, and electron microprobe analysis to characterize their differences in mineralogy and textures. Good sinters consist predominantly of hardysonite, franklinite, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite, and zinc-lead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of about 15-20%. Bad sinters contain larger amounts of lead silicate matrix, galena, metallic lead, and lead oxides, but smaller amounts of hardysonite, franklinite, and calcium-magnesium-iron silicate, lack intimate intergrowth of the phases, and have lower (0-5%) and unevenly distributed porosity.

Jan 1, 1992

By Jian Li, Pei Liu

In recent years, focused ion beam (FIB) has become a powerful microscopy tool. Creating large FIB cross sections are often required to characterize important microstructure features e.g. the depth and morphology of pitting corrosion and stress corrosion cracking in natural gas pipeline steels. Large FIB sectioning often takes long time that not only occupy valuable FIB microscope time, but also consume often expensive consumables that include gallium ion source, aperture and deposition gas etc. The new plasma FIB developed by FEI can speed up milling process by using much larger beam current. However, for most of the laboratories that is limited by conventional Gaion FIB, the milling speed is limited by the relatively small beam current. In this paper, FIB milling rate are studied against milling parameters that include beam dwell time and pixel overlap. By optimizing the milling parameters, milling rate can increase significantly.

Mar 1, 2018

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Gerardo R. F. Alvear, Alistair S. Burrows, Stanko Nikolic, James S. Edwards

"The copper ISASMELT™ process has evolved over more than a quarter of a century and can now be considered mainstream, with single furnaces producing more than 340,000 tpa of copper in matte. The next evolutionary step for the ISASMELT™ technology is to directly challenge the dominance of the Peirce-Smith converter by the implementation of a continuous copper converting process on a commercial scale. The present work describes the status of the continuous converting process – ISACONVERT™.Continuous converting has been performed successfully in pilot scale ISACONVERT™ plants, where operating results have verified the predictions of fundamental research and reinforced the underlying confidence in the design parameters. From a matte feed rate of 250 kg/hr, a calcium ferrite slag and a low-sulfur blister have been produced. Design is now complete for the first commercial application of the ISACONVERT™ process. The present paper describes the status of ISACONVERT™ by summarising results of recent pilot plant tests and describing the first commercial plant design."

Jan 1, 2009

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang

"Manganese is mainly consumed by steel and battery industries. In recent years, it is essential to utilize the low-grade manganese oxide ores with total manganese grade below 25%, as the high quality manganese ore resources are becoming scarce with the rapid development of the steel industry. Conventional pyro-metallurgical processes for utilizing manganese oxide ores are characterized by high production cost and energy consumption, low productivity, serious environmental pollution, etc. In this study, reduction thermodynamic of MnO2 reduced by sulfur was firstly carried out. Then, a novel process of reduction roasting with sulfur followed by acid leaching was developed to recover manganese from the very low-grade manganese oxide ores. Effects of main factors, including temperature, reduction time and S/Mn mole ratio, were investigated, and a high leaching efficiency of Mn above 95% was obtained under optimal conditions.IntroductionHigh/middle-grade manganese oxide ores are generally used in the metallurgical industries, particularly in steel plants and ferro-alloy units. The consumption of metal manganese in the ferro-alloy industry accounts for 85- 90% of the total Mn demanded [1]. Therefore, high quality manganese ore resources are becoming scarce with the rapid development of steel industry. It is essential to make good use of large quantity of low-grade manganese ores (TMn < 25%) presently available."

Jan 1, 2012

By Soumitro Nagpal

Bacterial oxidation of a pyrite-arsenopyrite-gold ore concentrate was carried out in .14-liter continuous-flow stirred-tank reactors (CSTR). Oxygen and carbondioxide consumption rates mineral dissolution rates, and bacterial concentrations were measured at various steady-state residence times and with 6, 11, and 16 wt.% solids in the feed slurry. A sharp optimum in biooxidation rate .was found at a residence time of approximately 40 hours for operation at each of the three pulp-densities. Biooxidation rates increased consistently. with increasing pulp density. Cell washout accompanied by negligible biooxidation rates was found to occur at a residence time of approximately 20 hours. Mineral&apos; oxidation was found to be strongly dependent on bacterial activity. Arsenopyrite was found to be preferentially oxidized? at the higher Pulp densities.

Jan 1, 1991

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Zhigang Liang

Effects of the configuration parameters of submerged entry nozzle on the flow field in slab mold were investigated through a water modeling. The experimental results showed, when the original submerged entry nozzle was applied, there was an appreciable level fluctuation in the mold with obviously naked surface and entrapment of mold flux at higher casting speed. By increasing the outlet area of submerged entry nozzle, without any change of other configuration parameters and submergence depth, a proper fluid field with active surface and good covering of mold flux can be obtained, which is proper to meet the requirement for increasing the casting speed and improving the slab quality simultaneously.

Jan 1, 2009

By Balladares V. Eduardo

Most of the arsenic contained in copper concentrates is removed in the gas phase during the smelting and converting processes and, according to recent environmental regulations, it is required to fix it in a solid stable form. In this regards, ferric arsenate has been reported as thermal and aqueous stable compound. Therefore, various alternatives for treating gas containing arsenic were considered in this work. From data obtained at laboratory scale on fixation of arsenic using iron oxide, a new process to treat copper concentrates containing arsenic was evaluated. The effect of temperature, oxygen potential and the sample porosity on the fixation of arsenic contained in a gaseous stream was studied, and the iron oxide converted into ferric arsenate was up to 10%. The obtained results suggest a new alternative for gas treatment with an interesting and attractive technical development. The arsenic was retained as ferric arsenate with thermal and aqueous stability, and it allows a safe disposal keeping the environmental restrictions. The kinetics parameters are used to scale up laboratory results to higher processing rates.

Jan 1, 2005

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009

By Omid Lashkari

Keywords: SEED, SSM materials, Microstructural evolution, Rheology, Swirling Speed SEED (Swirled Enthalpy Equilibration Device) is established itself as a new technology amongst the many Semi-Solid Metal (SSM) processes, where swirling of the mush plays an important role in modifying the dendritic structure of as-cast parts. A range of semi solid metal structures, dendritic, rosette and/or globular morphology of primary phase, can be prepared using SEED. The current article reports on the application of rheological tests in characterizing microstructural evolution during SSM processing of 356 Al-Si foundry alloy. A simple parallel plate test machine, designed and constructed at our labs, was used to determine viscosity values for each structure and identify the optimum structure with superior die filling characteristics. Such findings have important technological and economical implications during high pressure die casting of semi- solid metals. The strain-time graphs for 356 Al-Si foundry alloy indicated lower viscosity values for globular microstructure, i.e. improved die filling.

Jan 1, 2005

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By Józef Czernecki

The Polish copper concentrates are characterised by low content of sulphur and iron. At KGHM Polska Miedz S.A. two copper production technologies are in use. The shaft furnace process is used at the Legnica Copper Smelter and the Glogów I Copper Smelter. A single-stage direct to blister Outokumpu flash smelting process is used at the- Glogów II Copper Smelter. Melting copper concentrates in the shaft furnaces is carried out in a reducing atmosphere and the product obtained is a matte. Instead, a result of melting copper concentrates by an oxidising flash process blister copper of a quality similar to that of converter copper is obtained. The annual copper production at KGHM Polska Miedz S.A. exceeds 450,000 tons. Another important metal is silver produced from slimes from copper electrolysis (about 1000 t/y). Moreover, such metals as Pb, Ni, Se, As, Au and other precious metals, including Pt and Pd, are recovered from various semiproducts. This paper presents technological flow sheet of the copper production in plants using the shaft furnaces and in another plant in which a single-state flash process is applied. Characteristics of products, methods of their utilisation, main parameters of particular technological operations, and advantages and shortcomings of the solution applied are presented. There are also discussed: the natural environment protection as well as directions of the KGHM Polska Miedz S.A. plants modernisation.

Jan 1, 1999