Search Documents

By D. Maurice, W. D. Riley, J. A. Hawk

"The increased penetration of wrought aluminum into the automotive market is stimulating a need to separate wrought aluminum from cast aluminum because of: a) the additional value of scrap wrought alloys and b) the increase in the total amount of aluminum automotive scrap will outstrip the demands of secondary aluminum foundry industry. The availability of clean fractions of wrought and cast aluminum and incidentally, a clean cast magnesium fraction will allow increased recycling of aluminum used in the automotive industry.Hot crushing has been tested previously and proposed as a means to separate cast from wrought alunrinum product. The underlying concept is that when a mixture of cast and wrought aluminum is thermally processed and then subjected to crushing action, differences in toughness between wrought and cast aluminum alloys will become more pronounced. Hence, it should be possible for conditions can be established such that the cast material fragments, while the wrought material, having lost much less of its toughness, merely deforms. The two types of product could then be separated by simple sizing methods.In this paper we report on the testing of this concept. We were unable to replicate the results which originally demonstrated proof of concept. Possible reasons for this are discussed, as well as the possibility that the original results may not be as desirable as the current results for subsequent sorting."

Jan 1, 2000

By Peter C. Hayes

"The high temperature reduction of solids through the use of reactive gas atmospheres has application in a wide range of industrially important processes. Whilst significant advances have been made in understanding and describing these processes, some key aspects of the chemical reactions and reaction mechanisms operating in these systems, for example, the transformation from metal oxide to metal, remain poorly understood. A number of different product morphologies have been identified in these reaction systems and the reaction rates have been shown to be critically dependent on the product structure.Theoretical examination of the elementary process steps taking place in the region of the gas/metal/metal oxide interface, combined with electron microscope studies of the resultant product microstructures, have enabled the key process and material variables responsible for the development of the various product morphologies to be identified. By considering i) established criteria for the stability of moving interfaces in a thermodynamic potential gradient, ii) the relative rates of chemical reactions on the oxide and metal surfaces, and iii) key process phenomena and physico-chemical properties of the solid phases, the mechanisms and conditions for the formation of various product morphologies are identified. Interestingly the analysis points to direct analogies between these phase transformations and, the phenomena and microstructures observed in metal solidification, and the potential to develop generic models of these fluid/solid reaction systems."

Jan 1, 2013

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Shengli Wu, Fengjie Zhang, Feng Chang, Hua Lu, Kaiping Du

In order to make a complete understanding of steel plant metallurgical dusts and to realize the goal of zero-waste, a study of their properties was undertaken. For these purposes, samples of two sintering dusts (SD), two blast furnace dusts (BFD), and one electric arc furnace dust (EAFD) taken from the regular production process were subjected to a series of tests. The tests were carried out by using granulometry analysis, chemical analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy via SEM (EDS), and Fourier transform infrared spectroscopy (FTIR). The dominant elements having an advantage of reuse are Fe, K, Cl, Zn, C. The dominant mineralogical phases identified in sintering dust are KCl, Fe2O3, CaCO3, CaMg(CO3)2, NaCl, SiO2. Mineralogical phases exist in blast furnace dust are Fe2O3, Fe3O4, with small amount of KCl and kaolinite coexist. While in electric arc furnace dust, Fe3O4, ZnFe2O4, CaCO3, CaO, Ca(OH)2 are detected.

Jan 1, 2015

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By V. L. Stolyarova

As part of an effort to develop the fluoride electrolysis route for the production of rare earth metals and alloys, a study of the thermodynamic properties of DyF3 has been carried out by Knudsen cell mass spectrometry. A quadrupole mass spectrometer QMS 420 was used in conjunction with the Knudsen cell arrangement. The experiments were carried out in the temperature range 1280-1440 K. Vaporization was carried out from platinum, molybdenum and tantalum cells. The Dy*, DyF+, DyF2+ fragment ions and the DyF3 parent ion were identified in the mass spectrum of the DyF3 vapour. The DyF, vapour pressure was obtained by the complete isothermal vaporizadon method as well as the ion current comparison method, and the enthalpy of sublimation of DyF3 was evaluated. From the DyF3 vapour pressure data obtained at different temperatures, the enthalpies of formation of DyF3 in the gaseous as well as condensed phases have been evaluated. The experimental data are compared with the thermodynamic information available in literature.

Jan 1, 1995

By Pedro A. Netto, Sergio N. Monteiro, Foluke S. de Assis, Rômulo L. Loiola, Frederico M. Margem

Banana fibers are among the lignocellulosic with great potential for use in polymer composites, such as the variety from the Musaceae family, due to its low density and good mechanical properties. In this work, epoxy matrix composites incorporated with continuous and aligned banana fibers were tested for their flexural behavior. Specimens with up to 30% in volume of fibers were bend-tested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractographic analysis by SEM examinations a moderate adhesion mechanism between the banana fiber and the epoxy matrix. This mechanism is apparently responsible for the improved performance of the composites.

Jan 1, 2015

By Ningchuan Feng

A biosorbent, the chemically modified orange peel, was prepared from hydrolysis of the grafted copolymer, which was synthesized by interacting methyl acrylate with cross-linking orange peel, and FT-IR spectroscopy was used for determining the structure of the biosorbent. Adsorption characteristics and effects of various factors of the biosorbent on Cu (II) were investigated including pH, adsorption time and initial concentration of Cu (II). Experiment results show that when pH was 6.0 and the initial concentration of Cu (II) was 50mg·L-1, the removal rate was 91.7% after 3 h adsorption. After four cycles being reused, 85.3% removal rate could be obtained by the biosorbent.

Jan 1, 2008

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By R. G. Reddy

To better understand the behavior of bacterial-mineral interfacial reactions, a thermodynamic model based on the- studies of bacteria adhesion on mineral surfaces has been evaluated. The bacteria adhesion to the mineral surface would be increased by l ' d1;1creasing the change in Gibbs free energy of adhesion and it would be reduced if the change in Gibbs free energy of adhesion of the system is increased. From the combination -of Young's equation and equation of state, the change in Gibbs free energy of adhesion -for bacterium-mineral system- was calculated. Influence of liquid surface tension, mineral surface tension on the change in Gibbs free energy of adhesion and consequently bacteria behavior on mineral systems- has been discussed.

Jan 1, 1991

By Victor Zavodinsky, Sergey Rogov

"Pseudo-potential fully relaxed total energy calculations are used to predict a hypothetical Si1-xCxO2 (x<0.5) compound formed from SiO2 ß -cristobalite by substitution of some SiO2 complexes by CO2 molecules. The simulation shows that the Si1-xCxO2 compound can be quasi stable if the CO2 content is less than fifty per cent. It is assumed that six-molecule Si6-nCnO12 (n=3) rings can play a role of nucleuses for formation of the Si1-xCxO2 compound from SiO2 and CO2 molecules. Thus, silicon dioxide can be considered as a possible solid store for gaseous CO2.IntroductionThe problem of increasing of CO2 in the Earth atmosphere is one of the main modern problems of mankind. One of conceivable ways to decrease the harmful value of CO2 is to convert a part of it to solid state. Iota et al. [1] reported a polymeric (quartz-like) phase of CO2 solid synthesized at high pressure (~40 GPa) and at high temperature (~1800 K). Shortly after this experimental work, Serra et al. [2] reported a total energy calculation of several possible phases of CO2 using plane wave pseudo-potential density functional theory. They concluded that there should be a transition from a molecular phase to a phase isostructural to SiO2 -quartz in the range of 35 to 60 GPa. The latest calculations by Dong et al. [3] have shown that the more favored solid CO2 phase is ß -cristobalite. Recently, Kume et al. [4] have demonstrated the polymerization of CO2 even at room temperature at high pressures up to 80 GPa. Transformations of gaseous CO2 to different solid phases were studied recently experimentally and theoretically [5-8]. The main obstacle for using synthesized CO2 solid as a solution for the CO2 problem is its pressure instability. However the SiO2 ß -cristobalite with the same structure is stable.The question is whether a silicon-oxide system in which a part of atoms of silicon is replaced by atoms of carbon will be stable? If the answer is positive, this system can be considered, in our opinion, as a possible store for CO2."

Jan 1, 2009

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

In the last decades, authors have been focused in the development of a cyanide-free bath for the electroplating industry of brass due to the risks that involves the use of cyanide and they have been evaluated the electrodialysis as an alternativemethodforthetreatmentoftheeffluentgeneratedinthistypeofindustry because ofthe limitationscaused bythe chemical precipitation. Hence, thepresent paperaimedtodeterminethelimitingcurrentdensityoftheeffluentgeneratedinthe free-cyanide electrodeposition of copper and zinc using EDTA as chelating agent for the treatment of the effluent by electrodialysis. The synthesized solutions were preparedwith copper sulfate andzinc sulfate indifferent conditionsofpH (10–12) and proportion of cupric ions (30%, 50%, 70%). According to the results, the increase of pH and the cupric ions proportion caused an increase in the limiting current density because of the larger amount of anionic species in solution and the consequent difficult to achieve the concentration polarization phenomenon. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By Daniel Chen, Jewel Andrew Gomes, Venkata Palla, Sadia Afrin Jame, David Cocke, Paul Bemazzani

"Textile industries use various kinds of chemicals including dyestuffs and pigments during dyeing and finishing processes. The effluent from these processes includes suspended particles, strong color, high pH and high chemical oxygen demand (COD) that are extremely toxic and make environmental hazard. Although physical, chemical, photochemical, and biological methods are available for treating such wastewater, the electrochemical technique, electrocoagulation (EC), has emerged as an efficient, simple, and cost-effective technology in the last few decades. In this study we present the applicability of EC technique for removing dye, such as direct red dye using iron electrodes, and the optimized conditions such as dye concentration, current density and pH. The degradation of dye molecules was investigated using UV-visible spectroscopy. The EC-floe was also characterized using SEM/EDS, XRD and FTIR.IntroductionWastewaters generated by textile industries contain large amounts of toxic aromatic compounds, especially azo dyes. Azo dyes and their degradation products, such as aromatic amines, are highly carcinogenic. These effluents are also responsible for causing high levels of color. The colored wastewater released into the environment is also a source for disruption of aquatic life and aesthetic pollution as well [1].In most textile industries, dyeing and finishing are the two important processes which are generally applied. These two common processes generate significant amount of wastewater, which may contain, suspended particles, high pH, strong color and high chemical oxygen demand (COD) concentration [2]. Low pH and high temperature are other polluting factors from the waste water. Textile industries make use of about 10,000 dyes and pigments [3]. Disposal of these colored wastewaters poses a major problem for the industries as well as a threat to the environment. In textile industries, because of the low efficiency (60-90%) of dye fixing on textile fibers, substantial amounts of unfixed dyes are released in waste waters. The conventional method for treatment of textile wastewater was a combination of biological, physical and chemical methods [2]."

Jan 1, 2011

By W. Y. Kim, K. H. Song, K. Nakata

"The present study was carried out to evaluate the mechanical properties of friction stir welded Inconel 600/SS 400 lap joints. In this process, friction stir welding (FSW) was performed at a tool rotation speed of 200 rpm and welding speed of 100 mm1min, and argon gas was utilized to prevent surface oxidation during the welding. Application of FSW notably decreases the grain size of Inconel 600 alloy from 20 µm in the base material to 8 ~ in the stir zone. However, the grain size of SS 400 in the weld zone was slightly coarsened, when compared to the base material. Also, the hooking in the advancing side and the intermetal1ic compounds (M7C3) in the weld interface between Incone1 600 and SS 400 were well formed. These intermetallic compounds and hooking were effective to increase in mechanical properties such as tensile and peel strengths.IntroductionFriction stir welding (FSW), applicable welding process at solid state, has several advantages in defect suppression such as blow hole, segregation and cracking which mainly occurs in fusion welding [1, 2]. Notable grain refinement in the stir zone due to FSW can expect the outstanding increase in mechanical properties of the welds. In constructing the chemical and power plants, Ni base superal10ys have been used in many parts, moreover, fusion welding as construct method, such as gas tungsten arc welding, electron beam welding and laser welding, has been mainly used [3-5]. However, fusion welding has a limit in an increase in chemical and mechanical properties in the welds. Lately, Ni base superalloys to which FSW applied have been reported with notable enhancement in mechanical properties, which resulted from refined grains in the welds [6-10]. These researches showed the possibility in applying the FSW, directly."

Jan 1, 2012

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003