Search Documents

By Antonio Martin, Jesus Hurtado, Francisco Jimenez

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities, including a primary copper smelter and an electrolytic refinery, are located in Huelva, on the southwest coast of Spain. These installations enable the smelting of over 1 million tpy concentrates to produce up to 260,000 tons per year of cathodes and 900 ktpy of sulphuric acid.Since 1970, several improvements have been made at the Converters Area such as modifications of primary hoods, operations with an OPC system, installation of scrap chargers, the recent installation of the secondary hoods and other environmental projects. All these modifications have been aimed at increasing the capacity of our smelter while keeping our continuous environmental commitment.This paper describes the modifications and improvements carried out at the converters area and our proposals for future developments."

Jan 1, 2012

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By Z. Yang

The flotation behavior of the. green algae Chlorella vulgaris and a wild Chlamydomonas spp. was studied in the presence of Zn(II) using dodecylammonium chloride as collector. At about pH 6. both organisms readily float as amine concentration approaches lx10-3 kmol/m3. In addition, electrokinetic measurements were made on the organisms as a function of pH in both the presence and absence of Zn(II). It was found that the Zn(II) has a considerably greater effect on the zeta potential of C. vulgaris than on Chlamydomonas. Zn(II) adsorption studies also indicated that C. vulgaris is able to accumulate more Zn from solution than the Chlamydomonas.

Jan 1, 1991

By Mike Adams

A comprehensive pre-feasibility study has been conducted by Companhia Vale do Rio Doce CVRD) for Niquel do Vermelho nickel laterite deposit. Within this study, five integrated flowsheet options were evaluated via batch and pilot campaigns at Lakefield Oretest, over an intensive six-month period from receipt of ore to final reporting. Key technical objectives set by the client included demonstrating the technical viability of the beneficiation of several ore types, processing through integrated pressure acid leach/mixed hydroxide precipitation (PALIMI-IP) and mixed sulfide precipitation (PALIMSP) circuits, and the treatment of barren liquors to meet stringent environmental requirements. Refining of the MHP was by ammonia re-leach and solvent extraction (SX) to produce LME-grade nickel cathodes, NiCO3, NiO and CoS. LME grade nickel and cobalt was also produced by oxidation of the MSP and hydrogen reduction on the leachate. The database and data acquisition system, along with web-based reporting, enabled rapid turnaround on both daily and more comprehensive run reports, making it possible for speedy and confident decisions on operating conditions of the complex flowsheets. The high value of developing such data is emphasized and discussed as pivotal in the successful progression of laterite projects through to sustainable commercial viability. Keywords: Flowsheet, CVRD, Nickel, Piloting, Pressure, Leach, Refining.

Jan 1, 2004

By Robert W. Bartlett

"Economic and other factors, mostly outside of metallurgy, that strongly influence applied research, development and especially successful commercial adoption of new processes for producing primary metals and other commodity materials are reviewed. These factors, which can be both positive and negative in their influence, are often too lightly regarded in the research planning stage. They include continuing imperatives that have long influenced new process development as well as more recent trends. Both are discussed. Nearly all new materials eventually become commodities--products made to standard specifications with no producer control over price. Success requires being a low cost producer on a world wide basis. Composites and other complex material assemblages are unlikely to escape this fate as they mature.INTRODUCTIONThe adoption of new processes, beginning with research and development, for primary metals and other commodity materials is particularly difficult because each new process must supplant an existing process that is already being used commercially. There are many requirements besides technical innovation and cost superiority that must be met by the new process. Consequently, few innovations make it all the way from the research laboratory to commercial success.This paper discusses some of the factors that influence success in developing new processes for primary metals and commodity materials, based on the authors experience as a research metallurgist and industrial research manager. It begins with some of the factors that are always present and constrain successful process research and development, and proceeds to current trends that are expected to continue long enough to influence processes in the year 2000. Many of these trends are contradictory in their effect on new process development, and the future remains uncertain.The prevailing importance of these trends will vary with the material, process concept and other factors intrinsic to each case. Nevertheless, an awareness of these influences can help to avoid some of the R&D pitfalls and dead ends. Such awareness is deemed to be a necessary condition to avoid failure when commercial adoption of a new process is the goal."

Jan 1, 1988

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By E. Maziar Sauber

In order to prepare a more desirable feedstock for a rare earth elements separation refinery, cerium, a penalty element in the refinery feedstock, should be removed from the mixed rare earth elements oxide or carbonate feedstock. In this study, cerium (III) to cerium (IV) oxidation by calcium hypochlorite and subsequent precipitation was used to remove cerium from a mixed rare earth elements chloride solution. A factorial design of experiments was used to determine the effect of process variables such as temperature, pH, and oxidizer addition on the oxidation of cerium (III) using synthetic solutions. Under certain test conditions, all of the cerium was successfully removed from the chloride solution, and some REE accompanied cerium and reported to the precipitate. This proposed technology can allow for low cost removal of cerium from mixed rare earth elements chlorides.

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel's Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By James T. Skoch

With the ongoing pressure on the secondary aluminum business to limit the amount of waste generated from processing aluminum dross, it becomes very advantageous to preprocess the dross to reduce waste. The advantage of preprocessing is that it significantly reduces the oxides and salt cake generated when melted. Various products can be produced from the oxides for the steel industry. The following paper will demonstrate that removal of oxide fines before melting will result in large volumes of material not being landfilled. We will show that the end result of this technology is to significantly reduce the amount of salt cake sent to a landfill while maximizing the recyclability of the aluminum dross.

Jan 1, 1995

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"The use of electromagnetic field to remove suspended particles from metals such as aluminum by pushing to the boundary has been well studied. However, the potential of this method is yet to be exploited for the removal of inclusions from silicon. Considering the increasing amount of Top-cut SoG-Si scraps year upon year, there is the need to harness all the potentials of technologies to recycle this materials to ensure sustainability. This study investigates, and discusses new results on the effect of processing parameters such as composition, coil current, and frequency on the removal of inclusions from silicon under high frequency AC electromagnetic field.IntroductionThe solar cell silicon making industry requires pure and clean silicon in order to maximize the conversion potential of the solar cell material. The conversion efficiency of solar cells is limited by minority carrier recombination at dislocations and those intra-granular defects such as impurities, small clusters of atoms, or precipitates [1]. Recent global developments in the energy sector with a drive for the production of clean, reliable, and affordable energy have stirred a rapid growth in the production of photovoltaic (PV) cells.[2] Thus over the years, silicon based PV cells has seen a lot of growth as it has a PV market share of over 90 % [3] either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [4]. MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from the air absorption during solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [5]. For sustainability the silicon in the top-cut silicon scraps must be recovered. Therefore methods for removing non-metallic particles, such as SiC and Si3N4, from the silicon are important in order to recycle the top-cut scraps to a useful feedstock for the silicon solar cells manufacturing."

Jan 1, 2012

By Matthew John M. Krane, Christopher J. Vreeman, J. David Schloz

"A continuum mixture model of the direct chill casting process is used to model the transport phenomena and solidification behavior in the Direct Chill casting of an Al - 6 wt% Cu billet using Wagstaffs AirslipTM process. The model, which includes the transport of free-floating solid particles, can simulate the effect of a grain refiner on macrosegregation and fluid flow. Numerical predictions of sump profiles and composition and temperature fields are presented. Two 45 cm diameter billets were cast under production conditions with and without grain refiner. Temperature and composition measurements and sump profiles are compared to the numerical results. The comparison shows excellent agreement for the grain refined case. It is believed that an incorrect model assumption prevents good agreement in the non-grain refined billet. IntroductionDirect chill casting is a semi-continuous process in which molten aluminum enters the top of a water-cooled mold, is cooled, and forms a solid ingot drawn out below (Figure l(b)). The molten aluminum begins to solidify due to the cooling effect of the mold wall. As the ingot is withdrawn from the bottom of the mold, water jets impinge on the surface, directly cooling the billet and forming a solid layer around a liquid melt, commonly referred to as the sump.A particular defect that occurs in a wide range of casting processes, including the direct chill (DC) casting of aluminum alloys, is macrosegregation, the uncontrolled redistribution of alloying elements on the scale of the ingot during solidification. Macrosegregation in DC cast ingots can produce non-uniform mechanical properties [l], which affects the behavior of the metal during downstream forming and heat treat operations."

Jan 1, 2001

By W. K. Rankin

Achieving continued economic growth with social equity within the natural limits of the Earth's eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

Achieving continued economic growth with social equity within the natural limits of the Earth's 'eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By Serge Lavoie

Alcan's Guillaume-Tremblay plant, located in Jonquiere, Quebec, has been in operation since 1990. This was the first plasma dross processing plant ever built. In addition to the use of the plasma heating technology, Guillaume-Tremblay has other unique features making it a modern and efficient dross processing facility. This paper presents a general overview of the practical experience at the Guillaume-Tremblay plant. In particular, the utilization of plasma heating in industrial conditions, the metallurgical performance, the unique dross handling system, the control and information management system and the reclaiming of the by-products will be discussed. Finally, the use of the plasma process for salty dross will be addressed' briefly.

Jan 1, 1995

By S. Sugiyama, M. Kiuchi

"New metal working processes, such as the mashy-state mixing, mashy-state forging, mashy-state rolling and mashy-state extrusion are developed and applied to manufacture the so-called particle reinforced metals, fiber reinforced metals, particle reinforced cladding metals and so forth. These metal-ceramics composites are made of metal sheets, metal powders, ceramics particles and ceramics fibers. The mashy-state processes are also used to work those composites into bars, wires, tubes, plates, sheets, machine parts and other products. The working conditions necessary to manufacture sound composite products are clarified and the mechanical properties of the products are investigated. Through the investigation, it becomes clear that the mashy-state processes are useful and effective to manufacture metal-ceramics composites. It is al so known that these processes may be applied in various ways to development of new metal matrix compounds. IntroductionThe so-called metal-ceramics composites and processes to manufacture them are now being widely investigated in order to comply with increasing demands for new materials with novel and excellent mechanical properties and functions. The metal-ceramics composites are expected to have superior characteristics with respect to the elastic modulus, hardness, anti-wear resistance, high temperature strength and other mechanical properties to those of conventional metallic materials.The present authors ha v e been investigating into new metal working processes which are based upon the characteristics of metals and their alloys in the mashy-state. In the mashy-state, the metal (or alloy) includes both of the solid and liquid components. According to the fact that the partial melting takes place and the liquid component usually exists at grain boundaries, the metal in the mashy-state has quite different mechanical properties from those of the metal in the solid-state. Because of that the bonding force among grains is very weak due to the partial melting occurred at grain boundaries, the mashy metal has distinctively low flow-stress and high deformability. The mashy metal splits into grains or particles and sticks to others very easily. It is so soft as to be stirred up just like a lump of sherbet, but it is sufficiently viscous to be mixed up with other materials, such as ceramics particles and ceramics short-cut fibers."

Jan 1, 1988

By Günter Petzow, Hans Leo Lukas, Hans Jürgen Seifert

"The CALPHAD method (CALculation of PHAse Diagrams) has been extensively developed in the last 25 years and became a useful tool in materials science. Thermodynamic descriptions for the functions of state of unary, binary and ternary phases are derived by the optimization of phase diagrams. These functions are stored in computerized thermochemical databases and can be combined to extrapolate to multi component systems. Depending on special demand, the actually most advantagous presentations of the calculated results can be chosen: tables or in a clear graphical form as phase diagrams, phase amount diagrams or volatility diagrams. The method will be desribed by the system Ti-Si-C-N-O including the ceramic subsystem Si3N4-SiC-TiCi,N1_1,-C-N-O which is very important for the development of ceramic composites. The calculations give the thermodynamic stabilities of the condensed phases as function of temperature, concentration and partial pressure of different gas species. Adjusting the sintering conditions to these results the formation of unfavourable compounds or liquid phases can be suppressed.IntroductionThe CALculation of PHAse Diagrams (CALPHAD-method) of multicomponent systems provides the possibility to plan experiments very efficiently and avoid the experimental trial and error approach for the development of materials. The main problem for best use of calculated results is their interpretation with regard to the specific applications under consideration. Tables give the exact quantitative data for the treated phenomena. However, most important to make best use of these thermodynamic data is their graphical representation especially designed for the solution of specific problems, scientific as well as application oriented. Only well chosen graphical representations support a comprehensive understanding of the thermodynamic interrelationships and the transfer to the problem."

Jan 1, 1996

By I. C. Knight

The current levels of copper smelter by-product acid production are reviewed on a regional basis, together with the possible changes in the future. There will be increasing pressure for all smelters to achieve a sulphur capture level of at least 95% by the end of the decade.

Jan 1, 1996

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed: The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation. This paper is an update of that which the authors prepared for the Infacon X ferro-alloys conference.

Jan 1, 2004