Search Documents

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Xiaofei Guan, Adam C. Powell, Uday B. Pal, Srikanth Gopalan

This paper reports a solid oxide membrane (SOM) electrolysis experiment using an LSM– Inconel inert anode current collector for production of Mg and O2 at 1423K. The electrochemical performance of the SOM cell was evaluated by using various electrochemical techniques including electrochemical impedance spectroscopy, potentiodynamic scans, and potentiostatic electrolysis. The effects of Mg solubility in the flux on the current efficiency and the YSZ membrane stability during SOM electrolysis were discussed and examined through experiment and modeling. The electronic transference number of the flux were measured to assess the Mg dissolution in the flux during SOM electrolysis. A negative correlation between the electronic transference number of the flux and the current efficiency of the SOM electrolysis was observed.

Jan 1, 2014

By Tianzu Yang, Weifeng Liu, Shu Bin, Lin Chen, Wanda Bin

"Vanyukov Process has been mainly applied for processing copper and nickel sulfide ore for more than 30 years. Based on the understanding of the Vanyukov Process, researchers from China introduced the technology into the areas of lead, antimony and bismuth extraction by changing the furnace structure and technical flow, which greatly extended the application area and raised the processing efficiency, thus developed the oxygen-rich side-blow bath smelting (OSBS) technology in 2000. This contribution reviews the history of OSBS technology from four respects: the quantity, the furnace structure, the process flow and the application area. Its potential research direction and industrial application are also summarized.IntroductionVanyukov bath smelting furnace and related bath smelting technology were developed by researchers from Soviet Union who devoted comprehensive research on fundamental theory as well as engineering technology [1,5]. Vanyukov process has been applied for large industrial production since the 1970s and it is still one of the major methods in modem pyrometallurgy process. The appearance ofVanyukov double district furnace and joint double furnace in the past ten years, which are applied for copper smelting, is the most valuable advances of the Vanyukov process [7,8,9]. However, the application ofVanyukov process was limited in copper and nickel sulfide ore smelting, and few countries adopted this process except Soviet Union."

Jan 1, 2013

By Shengli Wu, Feng Chang, Hua Lu, Jianliang Zhang

Kinetic studies of the blast furnace dust (BFD) reduction process have been carried out under non-isothermal conditions. BFD pellets were made with bentonite as the binder. A Comprehensive Thermal Analyzer (TG-DSC) was used to determine the mass loss of pellets, which were heated at three heating rates of 10, 20, 30 K/min up to 1493 K. Furthermore, the metallization rate and mineral composition of BFD pellets heated to several different temperatures were analyzed by chemical analysis and X-ray diffraction (XRD). It was found that, with its inherent carbon resources as the reducing agent, the metallization rate of BFD pellets could reach 88% at most. The reduction and weight loss process of iron oxides mainly happens above 1273 K. In addition, from application of the Coats-Redfern equation the apparent activation energy of the reduction from wustite to Fe was 443 kJ/mol and the mechanism was interface reaction R..

Mar 1, 2017

By Susanne Pignolet-Brandom

Reflected light microscopy, and scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron images were used to determine if a "slick dross" with undesirable handling properties has an assemblage of phases distinct from normal dross. This study has found that in the normal dross the most abundant lead phases are lead sulfide and lead metal and the most common copper phases are copper-iron sulfide and copper sulfide. In the slick dross, the most abundant copper phase is copper-lead sulfide and the most common lead phases are copper-lead sulfide and lead sulfide. The resulting mineralogical information has provided additional insight into the causes of the handling problem and the reaction mechanism for the formation of normal and slick dross

Jan 1, 1988

By Pamela Bogust, York R. Smith

Photovoltaic (PV) modules are becoming an ever increasingly larger part of our energy portfolio. As more and more PV modules are installed and come on-line, management of end-of-life (EOL) modules becomes an important issue. Currently, management of overburden EOL PV modules is not an issue, but is anticipated to be by 2030. Recovery and recycling of valuable metals in PV modules presents several environmental and economic advantages. In this brief review, we will describe processes for refurbishing and recycling of PV silicon. These processes involve some combination of mechanical, thermal, and chemical processing, all of which all have their oPV) modules have become wn respective challenges. Also, projections of PV module material streams are also highlighted.

Mar 1, 2018

By R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains <l ppm CN and 20 ppb Se; concentrations of other major contaminants meet EPA drinking water standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85 pet of the cyanide. Exploratory research shows that other bacteria removed up to 79 pet of the selenium from chemically oxidized, low-cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By Geoffrey Brooks, Mehedi Bin Mohammad, M. Akbar Rhamdhani

Molten alkali nitrates are used commercially as thermal storage fluids (HTF) for solar thermal electricity generation. Their range of operation is limited by the thermal stability and this limits the energy (steam-Rankine cycle) efficiency of these processes. In this study, the effect of atmosphere on the thermal stability of nitrates was investigated using simultaneous thermal analysis techniques (STA). The use of oxygen (O2) as a blanket gas was found to delay the decomposition point of the ternary NaNO3–KNO3–LiNO3 (13.23–57.14–29.63 weight ratio) mixture by 55 °C. By which operating range will increase 65 °C more compared to the binary solar salt. Higher heating rates increased the decomposition point but had less effect on premelting and melting properties. Nitrogen monoxide, and O2 evolution after melting indicates concurrent reversible reactions. Similar phenomena were observed for single and binary nitrates. The eutectic melting point of ternary nitrate obtained from the STA agreed well with FactSage eutectic composition prediction.

Mar 1, 2017

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015

By S. L. Kher

The Singhbhum Copper Belt located in the state of Bihar in Eastern India bears evidence of ancient workings and indicates the existence of a civilized habitation in this region in the past. It was in 1833. how- ever, that the first official announcement of the occurrence of copper in the district was made. Although the occurrence was confirmed in 1847, it was not until 1857 that the first company was formed to exploit the deposits. This Company was dissolved in 1859 and from then until 1920, there were many unsuccessful attempts to develop and exploit the copper deposits in the Singhbhum area. In 1920. the Cordoba Copper Co. took an option on the Mosaboni area, which is nearly 10 km away from the present works located at Moubhandar, Ghatsila and exercising the option in 1924, purchased the mining rights from the Cape Copper Company. The Cordoba Copper Co. was then converted into Indian Copper Corporation Ltd. This was subsequently taken over by the Government of India in March 1972 and is now known as Indian Copper Complex (ICC), forming one of the two smelting units of Hindustan Copper Ltd.

Jan 1, 1976

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By Bora Derin

This study is a collection of both newly published and/or presented works on impurity capacity predictions in molten melts which were carried out by Derinetal. Some sulfide capacity prediction results of iron oxide containing ternary silicate melts and industrial lead and copper slags using the Reddy-Blander model and some impurity capacity predictions of multicomponent oxide and salt melts obtained using a Artificial Neural Network Approach are discussed.

Mar 1, 2017

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste-free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks&apos; hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982

By Dian Adisty, Leiv Kolbeinsen, Eli Ringdalen

In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO-gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high temperature phase. Transformation to cristobalite has been investigated and shown to be a slow process where the rate varies between the investigated quartz types. The effect of quartz versus cristobalite as SiO2 source has been studied for reaction (1) 2SiO2 + SiC = 3SiO + CO, by heating of pellets with SiO2 + SiC in Ar-gas. The reaction was faster with cristobalite than with quartz. Initial experiments indicates that this is the case only in Ar and not in CO-atmosphere The higher specific surface area of cristobalite is believed to contribute to the higher rate. The industrial consequences of the observed difference between quartz types are discussed.

Jan 1, 2014

By Patrik Fredriksson

Thermodynamic data concerning FeO-containing slags is of importance in ladle refining of steel. With a view to generate a set of reliable and self-consistent thermodynamic data for these slags, experimental determination of the activities of FeO in binary and ternary slags was carried out using the gas equilibration method involving CO-C02-Ar gas mixtures at steelmaking temperatures. The slag samples in Pt crucibles were quenched after the equilibration and subjected to chemical analysis. The thermodynamic activities of "FeO" in the slags were calculated from the experimental data. The results are incorporated into a thermodynamic description of silicate melts in the present laboratory. The model is based on a Temkin-Lumsden approach and is able to compute the thermodynamics of higher order systems from the lower order ones.

Jan 1, 2003

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998