Search Documents

By V. Jiricny

There is a growing need to process galvanized steel scrap from automobiles, etc., in order to remove the zinc coating that otherwise causes problems in remelting of the scrap in electric arc furnaces. One approach that has moved to the pilot plant stage is that of Metal Recovery Technologies, Inc., of East Chicago (MRI). That company leaches the zinc fiom the scrap with a sodium hydroxide solution. The leached and washed scrap can then be returned to the steel industry. What is left is a sodium hydroxidelzincate solution which must be processed to recover the zinc and the NaOH. Presently, this is done by MRI using electrodeposition on planar electrodes at moderate current density and the resulting zinc is in the form of fine powder which is hard to process into, say, zinc for galvanizing. MRI has supported an investigation of a novel electrode, the spouted bed electrode (SBE), for zinc electrodeposition. In laboratory cells, zinc particles with low porosity have been grown up to 3mm in size. Microanalysis of the deposited zinc showed low level of impurities. DC energy consumption values were usually in the range of 2-2.5 kWg which is well below the energy consumption of the existing cells (and of present-day cells for electrowinning from acid sulfate electrolytes). These results were achieved at current densities (few thousand A/m2) that are much higher than possible with conventional electrodes. Discussion is provided of the scale-up of the cell to a commercial scale.

Jan 1, 1998

By B. Boryczko, J. Norwisz, Jose Escobedo Bocardo, Z. Kolenda, A. Holda

"Classical thermodynamic analysis of any thermal and chemical process is usually based on the first law of thermodynamics. Such an approach is not sufficient when deeper understanding of the nature of each elementary process is required. The use of the first and second law of thermodynamics together is necessary to solve practical process more effectively. Enthalpy and exergy balances allow to enhance our understanding of thermal processes especially when cumulative consumption of energy and exergy is calculated. To ensure reliability of such an analysis the least squares method for adjustment of mass balances of principal chemical elements has been applied and described in detail. Numerical analysis has been carried out to compare two different processes of copper production – shaft furnace and flash smelting.IntroductionClassical thermodynamic analysis of any technological process is usually based on the First Law of Thermodynamics in the form of energy (enthalpy) balances. Such an approach is useful in engineering practice as it makes analysis easier in the global scale neglecting modeling of the elementary processes, allows calculation of the thermal efficiency and makes possible to control quality of the measurement results. Additionally, graphical presentation of the energy balance is simple in the form of Sankey diagram.In the case of aluminum electrolysis process, design of the new electrolyzer or its modernization is always based on the enthalpy balance.However, deeper thermodynamic analysis leads to the conclusion that such an approach is not sufficient. The First Law of Thermodynamics guarantees the exact equivalence of the various forms of energy (allowing all forms to be measured in the common unit such as joules) but it does not guarantee interconversibility. Thermal energy (heat) is in a peculiar and unique position, for whereas all other forms can be completely converted into thermal energy, the reverse process id impossible, only a portion of the heat can be converted into mechanical energy. Explanation comes from application of exergy balances. As we know exergy expresses the amount of mechanical work necessary to produce a material in its specified state from components common in the natural environment, in a reversible way, heat being exchanged only with environment [1]. Consumption of exergy connected with the fabrication of some considered product appears not only in the plant manufacturing the product, but also in all plants delivering raw materials for the final production process"

Jan 1, 2008

By Uchil Jayagopal, P. V. Krupakara, S. Manjunath

"This paper deals with the corrosion characterization of quartz particlate ZA-27 alloy metal matrix composites (MMCs). Quartz particles of size 50-80 microns are used as reinforcement. MMC's are prepared according to ASTM standards. Composites containing. 2, 4, and -6% by weight of quartz and unreinforced matrix were tested using 1 -N hydrochloric acid: The composite was found to be more corrosive resistant than matrix alloy. In each test the corrosion resistance of both alloy and composites were found to decrease with the exposure time.1. IntroductionMetal matrix composites- (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight 1-5. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments Particles reinforced MMCs has been the most popular over the last two decades.ZA alloy MMCs have most popular families being represented by. ZA-27 alloy reinforced with ceramic particulate. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior.ZA alloys have been used extensively in industry. This is attributed to their excellent fludity, castability and good mechanical properties. Among the zinc-based foundry alloys, the ZA family of alloy have been widely used during the past few years. ZA alloys have many advantage over aluminium based ones, especially high strength with a low casting temperature 8."

Jan 1, 2000

By Ryokichi Shimpo, Akio Fuwa

"In order to elucidate the present status of process-control technology, survey study has been made on the present process control schemes of representative copper smelting and converting processes in Japan. Conceptual control flow diagrams have been deduced and shown on respective functional reactors, i.e. drying, smelting, converting and fire-refining units, where the objective OUTPUT items are correlated to the INPUT variables through respective CAUSE-AND-EFFECT RELATIONSHIPSFuture view has been also discussed on several feasible and desirable improvement and refinement ~n measurements and control system for better copper smelting and converting operations.INTRODUCTIONIn other to seek for the better and efficient operation in copper smelting and converting process, survey study has been first conducted on the present process-control schemes of respective functional unit processes, i.e. drying, smelting, converting and refining unit processes, of representative copper production processes in Japan. Conceptual process flow chart of control scheme has been then deduced where output items are correlated to input items through the respective cause-and-effect relationships.After this survey study, future view has been discussed on the feasible and desirable improvement and refinement in the measurement and control system in these processes. Emphasis has been placed on the better and precise measurements of temperature, oxygen partial pressures in respective furnaces and end-point in converting and refining unit operations."

Jan 1, 1989

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By Chris P. Pistorius

Over the past few decades the carbon intensity of ironmaking and steelmaking has been reduced considerably through improved efficiency in blast furnace ironmaking, partial replacement of coke with less carbon-intensive fuels, and increased use of scrap and direct-reduced iron in steelmaking. To evaluate possible further reductions in carbon intensity accurate process information is needed. A preliminary test of the fidelity of publicly reported data as a source of process information is reported here. The sources are industry roundups of electric furnace furnace steelmaking and blast furnace ironmaking (published by the Association for Iron and Steelmaking Technology), and data recorded by the Environmental Protection Agency under the US Greenhouse Gas Reporting Program. From a comparison for an integrated steelmaking plant and an electric furnace furnace plant, it appears that the values from the two data sources are consistent. The comparison does rely on process details such as the quantitative relationship between injected oxygen and carbon emissions in electric furnace steelmaking.

By Edita Vircikova

The best demonstrated available technology (BOAT) for the removal of dissolved arsenic and some heavy metals as reported by USEPA (Contaminants and Remedial Options at Metal Sites, Draft Report, August 1993) (1) is still the chemical precipitation. Coprecipitation with the excess of iron is usually practised because of the availability of iron at low/no cost and also in order to meet the stringent regulatory discharge limits. The arsenic is usually removed with iron because of its common occurence in the mined orebodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compounds. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced.

Jan 1, 1995

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By Naixiang Feng, Kun Zhao

This work presents a two-stage aluminothermic reduction process for preparing Ti and Ti-Al alloys using Na2TiF6. Al-Ti master alloy and pure cryolite as co-products could be obtained. After the first stage reduction, the oxygen content of the metal product is reduced, and the second stage produces high-purity titanium or Ti-Al alloys with cryolite and Al-Ti master alloy as recyclable co-products.

Mar 1, 2017

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By S. P. Marsh, M. E. Glicksman

"The effect of capillarity-driven diffusion on the recalescence of mushy zones is studied in pure materials. The solid-liquid mixture is formed by rapid partial solidification of an initially undercooled melt, and the ratio of the two phases is subsequently maintained constant by an externally imposed adiabatic constraint. A novel technique has been developed that permits tracking of the kinetics of the diffusion-controlled evolution process in situ using precision temperature measurements averaged on a length scale larger than that of the microstructure.The mean ""temperature of a mushy zone is slightly below the bulk equilibrium melting point, and is related to a characteristic length scale of the microstructure through an appropriate statistical average of the GibbsThomson equation. Theoretical considerations indicate that the diffusion controlled recalescence will progress as t- l / 3, where t is time. This behavior is experimentally verified for both succinonitrile (SCN) and ethylene carbonate (ETC), which have markedly different morphologies. The kinetic rate constant is observed to increase monotonically with increasing volume fraction of solid in the two-phase mixtures, although a firm theoretical foundation for this result has not been developed.INTRODUCTIONA dispersed multiphase system seeking equilibrium will generally contain variations in the local .free energy density. These density variations arise from such factors as variations in the bulk free energies of the phases and the distribution of interfacial energies. In this study, we examine the kinetics of diffusion-controlled recalescence in 1 solid-liquid mixture of a pure substance at its melting point. This type of two-phase system is particularly convenient to analyze because of the well-characterized physical properties of pure phases (crystals and their melts) and their interfacial energies, and the absence of any solutal effects."

Jan 1, 1986

By James W. Evans, Dong Xu, Jr. Jones

A physical (water) model based on particle image velocimetry (PIV) has been constructed at UC Berkeley. The PIV technique enables the use of water modeling to quantitatively characterize the fluid flow behavior in the mold during the continuous casting of steel, in a whole field sense, i.e., section by section. A method to obtain e\e time-averagevelocity (TA V) vector maps was developed by averaging 40 instant aneous vectc -r plots revealing the time average features of the flow. Another benefit of TAV vector maps is the ability to compare with present mathematical models, which are mostly based on the time-average technique. Bifurcated submerged entry nozzles (SEN) with ports inclined at various angles to the horizontal were used in the modeling to study their effects on the flow inside the caster. Argon was also introduced into the model to simulate the influence of argon injection on the metal delivery from the tundish into the caster. The bubble sizes and distribution (in specific sections) of argon were characterized, at the same time, by the imaging system of the PIV. This will allow for validation of current mathematical models that were developed to simulate argon injection in casters. Comparison with results calculated by the commercial finite element package FIDAP is also presented.

Jan 1, 1998

By Neale R. Neelameggham

"Ferrous and non-ferrous metal industries are used to handling several billion tons a year of ore bodies, fuel and fluxing agents by mineral processing techniques and varieties of extractive metallurgy ""Reduction"" processes. Metal industry know-how can be applied to meet the challenge of Reducing CO2 in the atmosphere. Processes for generating alloys of carbon and hydrogen by Reducing the CO2 and water mixture, [carbonated water or water vapor] called Soda, to easily stored fuels are normally endothermic. The processes are similar to generation of hydrogen alone from water which is also endothermic. But hydrogen is more difficult to store than compounds [or alloys] of carbon and hydrogen. This recycling of CO2 and water are possible by using other forms of energy by innovative carbon capture methods.Thermodynamic Diagrams developed for Soda [CO2 and H2O] - metal reactions provide hints for using low cost unused stored energy in un-recycled metallic waste for thermal conversion. Choices for conditions for the electrochemical approaches [using solar - wind - hydropower] are also discussed.INTRODUCTIONIn 2006, I was reading some of the arguments put forth by learned scientists on the benefits and lack of benefits of bio-fuels. I found that the arguments rose partly from the differing system boundaries that were chosen by one versus the other. Some part of the argument may have been based on political climate or atmosphere rather than the analytical science. This situation is seen when scientists discuss which came first - the chicken or the egg, the fuel or biological matter, the oxide or the element, and so on.Then I thought –[just like many of the learned persons participating in this symposium] that common fuels - regardless of them being simple hydrocarbons or oxygenated hydrocarbons or carbohydrates - can all be made from the respective oxides of carbon and hydrogen by simple chemical reductions efficiently carried out in an economical fashion. This is the systematic approach we take when designing a chemical or metallurgical process facility."

Jan 1, 2008

By Honglei Zhang, Yue Wang, Guotao Xu, Li Liu

The influence of rich oxygen atmosphere on the properties and structure of castables used in the hot wind pipe of blast furnaces was analyzed. Results show that the cold compressive strength of castables is affected by the change of rich oxygen volume in the wind pipe, the bulk density decreases and apparent porosity of castables increases with the addition of rich oxygen in wind pipe. With the addition of rich oxygen, the velocity of heat transfer increase and result of the steel shell become over hot out of safe limit at the thin lining in hot wind pipe.

Jan 1, 2015

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By K. Sarveswara Rao

"Any innovative approach made in non-ferrous metallurgical industry centers upon developing new processes, saving materials, improving production quality, and bornagain materials. Aqueous processing is commonly used to treat lean grade or more complex ore bodies. Its sustenance largely depends on energy and environmental compliance including water and wastewater management. The present paper focuses the importance of using particle size distribution and surface area measurements during ammoniacal dissolution of a Cu-Pb-Zn sulphide bulk concentrate and with an overview of the effect of water salinity on the process chemistry and residue mineralogy. Accordingly, an effort is made here to discuss the emerging perspective and highlight the recent successes and trends in terms of energy savings in non-ferrous hydrometallurgy.IntroductionThe nature and structure of the global energy industry is likely to change significantly in the 21st Century. Rabago et al [1] have comprehensively discussed how the mining and minerals industries can adapt to the challenges and opportunities posed by trends and drivers in global energy use. According to the authors, the drivers of sustainability include water, efficient energy use, climate modification, transportation technologies and energy security. Sustainability and competitiveness for the minerals industry will depend on natural capitalism, resource efficiency, new processes, saving materials, improving production quality, born-again materials and the solutions economy. Based on this motivation, the theme of the present paper is centered upon applications as relevant to energy and sustainable development in non-ferrous hydrometallurgy."

Jan 1, 2009

By John R. FitzPatrick

The separation and purification of uranium from either nitric acid or hydrochloric acid media tan be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated' to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps. We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (100-gram) flow experiments using depleted uranium, were done after the small-scale evaluation Of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments' involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and' amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process. Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail.

Jan 1, 1996

By Wen Liangying, Zou Chong, Tan Xiuqin, Bai Chenguang, Zhang Shengfu

"Eight typical metallurgical byproducts containing iron were selected based on the effect of the chemical composition, particle size, additives on the burnout degree of pulverized coal. Effect of three typical byproducts including fine iron ore, BOF dust and BOF sludge on combustion reactivity and combustion efficiency were investigated using TG-DSC method. The results indicated that the three additives have obvious catalytic effects on pulverized coal. By comparison, the relative active sequence of byproducts to the catalytic combustion can be described as follows: BOF dust>BOF sludge>fine iron ore. Moreover, adding BOF dust as component of additives also shows significant catalytic effects on combustion efficiency during rapid heating process.IntroductionChina is the largest producer in the world with an annual output reaching over 6 billion tons. Solid wastes arising from iron and steel making increases the environment pressure in recently years. For instance, annual output of dust during the production of iron and steel making in China reach up to 5 million tons, which is close to 8%~15% of the amount of steel [1]. Another characteristic of these byproducts is they are finer particle which are just harder to deal with. Since some of solid wastes, including dusts, scales, and sludge, usually contain high iron content, sintering plants have traditionally been used to recycle byproducts in integrated steel plants in China. However these byproducts also have noticeable effects on sinter quality, sinter strength and productivity and, therefore, waste recycling is limited depending on the analysis of the waste materials [2]. Another method which is pre-treatment of byproducts in pelletizing process, increases of energy consumption and production cost. In addition, metallurgical byproducts often contain heavy metals and alkalis. For these reasons, recycling rate of the byproducts in China is very low. Therefore, how to recycle the byproducts in iron and steel making process is an important subject."

Jan 1, 2012