Search Documents

By M. Nishikawa

The Hachinohe Smelter employs the Imperial Smelting Furnace (ISF) for production of zinc and lead and handles a large number of concentrates and recycled materials. In recent years, recycled materials such as zinc-bearing materials, lead sludge and Waelz oxide have provided up to 30% of the feed materials at the plant. To allow for a satisfactory operation using such a wide range of recycled materials, the Hot Briquetting Plant was built in 1986 and started its operation in January 1987. In April 1988 the zinc production capacity of the ISP was increased from 81,000 to 101,000 tonnes per year. The additional production in the ISP has been attributed to the utilization of the hot briquetting process. This paper describes the various facts of the smelter, concentrating on hot briquetting operations and treatment of hot briquettes in the ISF.

Jan 1, 1991

By Luciano B. Oliveira, Alexandre M. Stumbo, Luis G. C. Marques, Valdo S. Marques, Sergio N. Monteiro

"Similar to the ethanol program, initiated more than 30 years ago, the recently created biodiesel program in Brazil is expected to rely on private initiative based on agribusiness for vegetable oil production. Campos dos Goytacazes is a large county in the northern of the state of Rio de Janeiro with land still available for oily vegetables plantation in addition to the land traditionally occupied by sugar cane plantation, which is used to produce ethanol. In order to extend the biodiesel program to Campos dos Goytacazes, the State University of Northern Rio de Janeiro (UENF) is conducting a technical project for the development of the infrastructure for biodiesel production. In this work, the infrastructure based on versatile equipment for biodiesel esterification built in the Center for Alternative Energy of the UENF is presented.IntroductionBiofuels are gaining worldwide attention as a possible economical solution for the prediction of declining reserves of petroleum and related increase in price of barrel. However, nowadays, a more relevant question is the climate changes caused by burning fossil fuels. This is especially the case of coal and petroleum based fuels, mainly gasoline and diesel that propel the majority of vehicles and generate a large amount of CO2 emissions responsible for global warming. This combination of economical an environmental problems is already providing a strong motivation to substitute conventional fossil fuels by renewable biofuels. More than just the interest of the market financial forces, government legislation is imposing a new order that obliges the use of biofuel. Many countries including the USA, the European Community, Japan and Brazil are committed to gradually substitute biofuels into their fleet of vehicles."

Jan 1, 2008

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By Yuzhe Zhang, Xiaodi Huang, Xinli Wang, Bowen Li, Matthew Andriese, Xin Yan, Jiann-Yang Hwang, Zhiwei Peng

Using a TM0n0 cavity system as the main reactor, an integrated process was developed to find the best condition for waste tire rubber to absorb microwaves. The penetration depth was the main character for determining the best condition. The penetration depth is defined as the distance from the surface into the materials at which the traveling wave power drops to from its value at the surface. The waste tire powder was irradiated by two different microwave frequencies, including 915 and 2466 MHz. The study was conducted with same powder size and atmospheric condition. The effects of temperature and microwave frequency were analyzed based on the experimental data. The main trends are higher the temperature, the absorption will be better and the higher the frequency, the better the absorption will be.

Mar 1, 2017

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By Chikabumi Yamauchi, Mitsuru Tanahashi, Jutaro Miura, Takaharu Iwadachi, Toshiharu Fujisawa

"Tue oxidation behavior of molten Cu-Be alloys was investigated by exposing· the molten Cu-Be alloys to various Ar-O2 atmospheres to control the oxygen partial pressure, PO2 = 10 ~105 Pa at 1423 K. The following results were obtained:• The oxygen · partial pressure in gas phase affects the morphology of the oxide formed on the surface of the alloy and · the oxidation rate of beryllium.• At lower oxygen partial pressure, a molten Cu-Be alloy is covered with a homogeneous and compact internal layer of BeO. Thus, the beryllium oxidation rate can be minimized.• By adding a small amount of calcium or zirconium into the molten Cu-0.5 mass% Be alloy, a protective BeO layer is formed even at higher oxygen partial pressure. Thus, the beryllium oxidation rate can be reduced.IntroductionCopper-beryllium (Cu-Be) alloys are well recognized for their unique properties, such as high electrical conductivity, high strength, high fatigue strength, excellent properties at elevated temperatures, good formability and good corrosion resistance. .This extraordinary collection of properties are the reasons why Cu-Be alloys are expected to be ""Key-materials"", which are necessary to further advance science and technology and to be applied in.various fields such as electronic devices, machine parts, repeater housings of undersea optical fiber communication cables, etc.However, a large amount of beryllium is oxidized to BeO in melting stage of the current Cu-Be alloy production process, because beryllium is a highly reactive element. This is one of the ·main factors that negatively affect the production yield and th_e product quality."

Jan 1, 2000

By Chaoying Ni, Dimitry Sediako, Prashant Karandikar, Sean Fudger

Neutron diffraction measurements were performed on steel encapsulated metal matrix composites (MMCs) in order to quantify bulk residual stresses. A coefficient of thermal expansion (CTE) mismatch induced residual compressive stress method is utilized as a means of improving the ductility of the MMCs and overall efficiency of several macro hybridized materials systems. Systems consisting of an A36, 304 stainless steel, or Nitronic® 50 stainless steel shell filled with an Al-SiC or Al-Al2O3 metal matrix composite are evaluated in this work. Upon cooling from processing temperatures residual strains are generated due to a CTE mismatch between each of the phases: steel, aluminum, and reinforcement. The analysis shows variation in the measured strain and stress results due to outer steel thickness, difference in CTE between materials, and relative position within the composite.

Mar 1, 2017

By Osamu Iida

Since 'start-up of the larger Mitsubishi Continuous Copper Smelting Process in 1991, furnace relining campaign was gradually prolonged to once every 2 years according to deregulation of governmental boiler inspection. On the other hand, in 1998 Naoshima smelter embarked on an intermediate strategic expansion plan to strengthell its international competitiveness. As part of this plan, modifications were implemented in the copper smelter designed to increase output of anodes from new charge source to 270,000 tpa. In May 1998, treatment of dried neutralized residue was started in C furnace, and during the shutdown for brick relining in April 1999, intensive modifications to the boilers as well as the installation of new spray coolers for furnace off gas treatment were implemented. Finally, the new larger oxygen plant was commenced its operation in May 2000 and the expansion was achieved around 30% increase of anode production from original design.

Jan 1, 2001

By Murali Thirukkonda, Rahul Shah, Srinivas Tangrila, Shankar Rachakonda, Jan Kajuch, Arthur Gurson

"High-temperature superconductors have potential for a variety of applications such as power generators, superconducting magnets for mine sweepers or ship propulsion motors, and magnetic levitation transportation systems. Interest in the use of superconducting wires and tapes increased dramatically after the discovery of high-critical-temperature (high-Tc) oxide superconducting compounds, which offer operating temperatures above that of liquid nitrogen. Several techniques have been proposed to produce commercially viable high-Tc oxide based superconducting wires. One of the promising methods involves multi-pass powder-in-tube (PIT) wire drawing followed by rolling and heat treatment. This work focuses on the development of a numerical model to simulate the PIT drawing process for fabrication of long lengths of silver sheathed Bi-2212 superconducting wires. The finite element based model was used to predict densification of the oxide powder, wire drawing forces, and silver sheath thickness during drawing. A cap-type pressure dependent constitutive equation was implemented in the model to simulate the powder behavior. The model incorporated experimentally obtained material data for the silver and powder. Results indicate that powder densification is increased by decreasing the initial silver thickness and increasing the silver strength. Data from wire drawing experiments were used to verify model predictions. IntroductionSuperconducting wires and tapes can be used to carry large dc currents with no measurable loss due to resistivity. When used in superconducting magnets for power generators, motors, levitation devices, magnetic detectors, or energy storage devices, they could potentially result in significantly reduced energy losses. In the past, most prototypes were tested in liquid helium at 4.2K [1]. However, the necessity to provide liquid-helium cooling systems proved to be a serious limitation in commercialization. In 1986 high-critical-temperature (high-Tc) oxide superconductors were discovered [2], which could allow for higher operating temperatures above liquid nitrogen (77 K). Since then, both academia and industry have concentrated their efforts on the development of high-Tc oxide superconducting wires, tapes and coils. As yet, large scale fabrication of long lengths of these wires with the required current carrying capacity and mechanical properties remains an enormous challenge."

Jan 1, 1994

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Guangxin Wu, Shunli Zhao

"Nucleation and growth model based on a 3D CAFE model, which was incorporated with macro heat transfer calculation within ProCAST software was used to predict the solidification microstructure of austenitic stainless steel in twin-roll strip casting. The simulation results of solidification microstructure agreed well with experimental results of austenitic stainless steel. The effect of different casting process parameters on the solidification microstructure was simulated. The predicted results show that solidification microstructure is obviously sensitive to superheat and convection heat transfer coefficient. With the increase of superheat, the grain density decrease and the proportion of columnar crystal increase. In addition, the proportion of columnar grains increases when convection heat transfer coefficient increases. Thus, it was demonstrated that the solidification microstructure evolution of twin-roll strip casting could be predicted reasonably by using this model.IntroductionNear-net-shape casting technology is an important research area in the iron and steel industry today. Twin-roll strip casting represents a major area of concentration of near-net-shape casting technology. It has been widely used for its outstanding advantages, such as extended solubility of alloying elements, refined solidification microstructure and reduced microsegregation [1]. Furthermore, it is the most environmentally friendly, energy saving, and C02-sensitive way to produce steel strips [2]. Therefore, much attention remains to be paid to this aspect. A lot of published works indicated that the solidification microstructure of twin-roll thin strip has obvious effect on the thin strip properties [3, 4]. For the accurate control of parameters of the process are made difficult due to the complicated process and the multi-fold factors, great attentions have been paid to numerical simulations to provide insight into the solidification behaviors of the thin strip formed by twin-roll strip casting [5, 6].Simulations of casting solidification can provide a method to predict microstructure and to improving strip quality by controlling the process parameters."

Jan 1, 2014

By A. Rawat

The removal of oxyanions of arsenic present in mine process water and drinking water to a regulatory level is a challenging problem. Recently a patented adsorbent lanthanum oxide has been developed which has shown strong specificity for the anions of arsenic. In this paper the kinetic and thermodynamic aspects of arsenic adsorption on to lanthanum oxide are discussed. Adsorption tests were performed at different temperatures using synthetic solutions of arsenic of varying concentrations. From the kinetic data and adsorption isotherms thermodynamic properties such as Gibb's free energy, standard enthalpy of adsorption, standard entropy, isosteric heat of adsorption and activation energy were determined. The results showed that temperature had a positive effect on the rate and degree of adsorption:The activation energy decreased with increase in the initial concentration thus indicating solute-solute interactions in the system. Also, the isosteric heat was found to decrease with increase in the adsorption density implying a heterogeneous adsorbent surface.

Jan 1, 1998

By Luiz A. Teixeira

This paper reports the results of kinetic studies involving the precipitation of arsenic from aqueous solutions as FeAs041 Fe(OH)3' using FeS04 as source of Fe ions, and Air or H202 as oxidizing agents. Both systems lead to an efficient removal of arsenic. The differences in oxidants performances are in the precipitation reaction rate -much faster using hydrogen peroxide. Mechanisms of reactions were suggested based on the following main steps:

Jan 1, 1996

By A. Andreas Hejja

Flow of slag and settling of matte in slag resistance electric furnaces are discussed in conjunction with furnace geometries, stirring action of the electrodes, buoyancy and electromagnetic effects. The rectangular electric furnace was regarded as a channel reactor and the mode of slag flow as a channel flow. The flow is affected both by buoyancy and electromagnetic forces, however the effect of electromagnetic forces is minimal. The flow velocity is made up of two components; (i) that developed by the action of the electrodes, and (ii) the bulk flow velocity determined by the smelting rate and the volume of the reactor. Slag samples were taken from various depths of the molten bath and were analyzed microscopically to determine the size and distribution of matte particles, The action of the electrodes was described by a simple mathematical formula indicating a balanced settling rate in the area of electrode action.

Jan 1, 1996

By Edward Rosenberg

The synthesis and characterization of silica polyamine composites modified with a variety of sulfur containing ligands is described. The two most successful ligands in terms of sulfur in-corporation and mercury capture are ethylene sulfide and carbon disulfide. The ethylene sulfide forms either an amino mercaptane or a polysulfide upon reaction with amino groups on the composite. The carbon disulfide undoubtedly forms a dithiocarbamate functional group upon reaction of the amino group under basic conditions. Both materials posses excellent capture kinetics and capacities for mercury, Once captured, the mercury is extremely difficult to remove from the composite materials, even with concentrated acids, and they easily pass the TCLP test. The materials are compared with related thioether modified silica polyamine composites and appropriate potential applications are discussed.

Jan 1, 2003

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016

By Sergio Neves Monteiro, Fabio Da Costa Garcia Filho, Dian Souza de Oliveira

The properties of the nickel based superalloys, in particular 718 nickel-based alloy, are mainly improved by the hardening mechanism, which is based on precipitation of second phases. This work aimed to compare the evolution of precipitation hardening in a 718 alloy microstructure for two different solubilization conditions: 1050 °C for 2 h and 970 °C for 2 h, followed by a period up to 120 h of aging at 800 °C and correlated to the values of hardness. The microstructure was analyzed by optical microscopy. Vickers hardness test was performed and the grain size was measured. It was verified an increase on the hardeness of this material up to 15 h of aging, after that the value decreased to a level that is maintained until 120 h for both solubilization conditions.

Mar 1, 2018