Search Documents

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By Ming-Feng Ye, Guang-liang Wu

The microstructure and mechanical strength variations of chromite pellets preheated and roasted in air were studied systematically. The results show that the chromite (Fe,Mg)(Cr,Fe,Al)2O4 is oxidized to magnesium-rich (Mg,Fe)(Cr,Fe, Al)2O4 and ferrochromium complex oxide (Cr,Fe,Al)2O3 in the preheating process over 500 °C. When the temperature is higher than 1000 °C, the new phase (Cr,Fe, Al)2O3 is formed, which is mainly distributed in the outer layer of a single chromite particle. Inner the particles there are acicular (Cr,Fe,Al)2O3 and unoxidized (Fe,Mg) (Cr,Fe,Al)2O4, which forming an interwoven structure together. The oxidation rates of pellets can reach to superior limits in 20 min. With the temperature increasing from 950 to 1300 °C, the mechanical strength and oxidized rates increase to varying degrees correspondingly.

Mar 1, 2018

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Molybdenum and nickel in black shale ore exists as amorphous sulfides which has highly active, and easily oxide to sulfuric acid and sulfate at low temperature in the presence of excess oxygen. Take advantage of the characteristic to leach molybdenum and nickel from black shale. Oxidation, conversion and dissolution behavior of amorphous colloidal molybdenum and nickel sulfide in pressure leaching process was studied. The effects of stirring speed, temperature, concentration of sulphuric acid, oxygen process and mineral granularity on molybdenum and nickel leaching were investigated. The results showed that dissolution rate increased with increasing temperature and stirring speed, but decreased with increasing concentration of sulphuric acid. And dissolution of molybdenum and nickel from ore only need oxygen without any other reagent.

Mar 1, 2017

By K. Adham

For use in many existing and emerging applications, the purification of natural graphite is required to achieve +99.9% carbon content with minimum metallic impurities. Currently, the hydrofluoric acid process is used, which carries certain environmental and workplace health and safety impacts. While thermal purification of graphite at temperatures over 2500 °C is a known alternative, such high-temperature furnaces are expensive to build and operate. Using chlorine at lower temperatures to purify graphite is also known and patented, but is currently limited to treating solid synthetic graphite shapes in small-scale batch furnaces. Chlorine treatment of natural flake graphite resources can be used commercially, if certain drawbacks are addressed through process improvements that can be helped with the use of fluidized bed reactor technology.

By Chi-Ming Chang

Alloy powders are commonly used in the purification of zinc sulfate solutions for use in standard electrowinning practice. The primary goal of this research was to study the use of zinc-lead alloys for similar reactions in the galvanic stripping of impurities from organic solutions. The effects of various parameters on the electrochemical behavior of commercially produced zinc-lead alloy powders were determined. A qualitative evaluation and summary of the influence of the more pertinent parameters on iron removal from di-(2-ethylhexyl) phosphoric acid (D2EHPA) by galvanic stripping is given. Water concentration, oxygen content and reaction temperature were the principal factors affecting the reaction rate and process efficiency. Activation energies were also calculated and indicated that the reaction changes from chemical to diffusion control .with increasing temperature in the range of 35" to 45°C. The results showed that zinc-lead alloy gave faster reaction rates with less sensitivity to process variables than SHG zinc as a reducing agent for galvanic stripping. The role of lead could be as cathodic sites for the reaction which enhances the zinc dissolution or anodic half reaction. The morphology of the zinc-lead alloy surfaces, before and after the reactions, supports this assumption.

Jan 1, 1998

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By V. I. Lakshmanan

"Historically flowsheets are developed for efficient separation of metals for economic recovery. With increasing emphasis on reduction, reuse and recycle (3Rs) efficient methods are sought to recover values from a variety of feeds where cost of collection, transportation, local consumer behaviour and regulatory guidelines dictate the development of economically viable flowsheets. Innovative understanding of potential market applications can provide means to develop value added end products. The paper with examples will discuss the use of innovative-separation technologies to obtain value added end use materials from secondary sources.IntroductionFlowsheets are developed for the efficient separation of materials of value for economic recovery. However with increasing societal pressures and regulatory initiatives for stricter environmental guidelines, there is strong need to provide focus to recover materials efficiently and economically in an environmentally accepted manner. North American industries are increasingly caught between demands for high technology value added products and responsibility for environment. An aspect that is receiving increasing attention is Design for Environment'. This incorporates a system wide approach for product design and incorporates environmentally preferable features such as recyclability, disassembly, maintainability, reusability and use of safe materials as part of a product's design objectives.The present paper with case histories will address innovative flowsheet development to convert wastes into recyclables value added products or for minimising generation of waste materials. Case HistoriesProcess for Separating Fibres from Composite Materials 1In the automotive industry, sheet molded compound (SMC) is used to produce panels, bumpers and the like. During the manufacture and at the end of life, considerable waste materials are generated which are potentially recyclable. Fibre reinforced plastics where fibre substrate impregnated with thermosetting resin, find applications in several manufacturing processes and are potentially recyclable at the end of life."

Jan 1, 1996

By Takahiko Okura

Sulphur, with its multiple oxidation states, play critical roles in many processes, ranging from regulating enzymes in plants, to acidifying aquatic systems, and to affecting the global climate. Most of non-ferrous smelters have been contributing to reduce atmospheric emissions of sulfur dioxide to acceptable levels, converting it to sulphuric acid and/or gypsum. However, some amount of SO2 gas is still emitted from isolated smelters. Furthermore, sulphuric acid is competing with involuntary elemental sulphur in the market. This situation puts the non-ferrous metallurgical industries to develop a new sulphur fixation process. This paper briefly describes the new technologies for fixation, followed by the novel proposal to convert SO2 gas to elemental sulphur using organic materials. Finally, the feasibility will be presented technologically and economically.

Jan 1, 2006

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By Cui Wang, Kexin Jiao, Qiuye Cai, Jianliang Zhang

Prolonging the campaign life of the blast furnace has been an important task for iron makers, and it has been studied for decades. Adding titanium-bearing materials is a generally agreed and effective technique to protect the blast furnace hearth. Titanium from titania additions in the burden or tuyere injection react with carbon and nitrogen and form scaffolds on the hearth surface to protect the hearth from subsequent erosion. In this article, the progress on blast furnace hearth protection of titania additions in Chinese steel companies and research institutions is investigated, and the difficulties in the operation and production, such as little effect after adding titaniumbearing materials and the property deterioration of liquid iron and slags, are analyzed. The future research for protection in Chinese blast furnace is proposed, and a comprehensive process which combines protection of titanium bearing materials with reasonable thermal balance and slagmaking regimes should be established.

Jan 1, 2015

By Peter J. Koros

The current wave of interest in this topic is the result of increased use of titaniferous ores or ilmenite in blast furnace burdens for the purpose of repairing hearth damage. The titanium compounds that promote deposition of ?patching? materials in blast furnaces are the cause of downstream problems in the steelmaking shops. Steelmakers historically have objected to significant amounts of titanium in hot metal (>0.10 % Ti) for several reasons: 1) accretions caused by the TiC.TiN needles that float out of the iron as it cools in transit and in transfers make the accompanying slag sticky and crusty, causing problems in desulfurization and increasing time and Fe yield loss at the subsequent raking, 2) defensive measures have been taken in treatment, such as use of argon for carrier gas, but without technical rationale for this approach, 3) difficulty in removal of the ladle slag by the raker, with subsequent sulfur addition to the vessel charge, and 4) transfer into the BOF and/or formation of a very corrosive TiO2 containing acid slag during the early part of the BOF blow which, in addition to causing lining damage, results in loss of sulfur removal capability by the vessel slag. Based on a conceptual analysis of the metal-slag-atmosphere interactions during transfer ladle desulfurization treatment, a mechanism is postulated for the apparent effectiveness of the use of argon in reducing the deleterious effect of titanium and an alternate technique, possibly more effective, is proposed. As probably the use of argon causes increased exposure to atmospheric oxidation of the titanium carbonitrides contained in the ladle slag, the same benefit can be obtained by use of either oxygen or an air blast to oxidize the noxious reaction compounds. Validity of the concept has been demonstrated in a pilot plant setting. These issues, and related effects on testing the hot metal, are examined in detail with reference to the literature and plant and laboratory experience.

Jan 1, 2006

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Guo Xueyi

The method of Substance Flow Analysis (abbreviated as SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level. In this work the flow of lead in China, 2006, was traced within the STAF model, and the situation of production, consumption and recycling of lead resources in China were introduced. The SFA is performed on lead flows during its one year life cycle in detail. As one of the biggest producer and consumer of lead in the world, China is facing a problem depletion of lead resources. How to increase the resource efficiency is a significant issue for lead industry of China. Based on the result, several suggestions were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of lead industry in China.

Jan 1, 2009

By Alicia E. Ares, Carlos E. Schvezov

In the present work it was observed the nucleation and growth of grains in the equiaxed zone of metal matrix composites (MMCs) samples directionally solidified wit the presence of columnarto- equiaxed transition (CET) in the samples. In order to do so, first, it was defined the difference between the real temperature at a given instant, which it is used in the analysis, its variation and furthermore, the variation in the solid fraction with time between the beginning and the end of solidification. It was determined a growth law assuming a lineal variation of equiaxed grain radius as a function of time, and also, it was expressed a law of grain density as a function of time, considering the presence of SiC and Al2O3 particles in the matrix. Finally, the results obtained were validated with measured values of grain density at each position of the thermocouples in the equiaxed zone of the solidified samples.

Jan 1, 2015

By R. Boom, C. F. Balentina, J. H. L. Voncken

During vitrification of bottom ash generated from the combustion of municipal solid waste (MSW), a Fe-Cu based alloy phase with great value was formed. In order to find proper commercial use in metallurgical industry, it is necessary to separate Cu and Fe. The present study focuses on the sulfide treatment at temperatures of 1400 – 1500oC, in particular with FeS containing minerals. Various sulfide compounds such as Na2S, Al2S3 and Ni3S2 were added to promote the copper removal. Pyrite and zinc sludge (containing ZnS) as waste streams were studied with specific interests. The results showed that both zinc sludge and pyrite are effective for copper removal with the highest removal efficiency of 95% by using pyrite. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in one step, and a multi-step operation is needed.

Jan 1, 2008

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006