Search Documents

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By Anders Salwén

In 1975 T. Nishizawa and A. Chiba reported on observed deviations from the ferrite-austenite local equilibrium in several diffusion couples based on the Fe-Cr system. In order to try to verify these results the austenite-to-ferrite transfonnation in a Fe-20 %Cr-Invalid Code [Fe-]-%Cr diffusion couple held at 1100 for 100 hours has been simulated. The simulation model is based on the postulated principle of maximum dissipation rate of Gibbs energy during transformation, which allows non-equilibrium interface conditions. Keynotes: Computer Simulation, Austenite-to-Ferrite Transfonnation, Diffusion Couple

Jan 1, 2003

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By S. Shrivastava

A structure based model has been developed for the prediction of viscosities of K20-B20, melts. These melts exhibit an anomalous behavior of viscosity with continuous variation in B203 content. A maximum and a minimum are observed at low temperatures, which disappear on raising the temperature above the softening range. The addition of K20 to the borate melts causes two opposing phenomena: (1) depolymerization effects and the related breakdown of network structure resulting in the formation of singly bonded oxygens, which weakens the structure and hence causes a decreases in viscosity, and (2) the formation of four coordinated borons (BO4 tetrahedra) which strengthen the structure leading to an increase in the viscosity. The structural changes taking place in these melts on varying the temperature and the alkali content have been reviewed and are incorporated in developing this model. The predicted values are in excellent agreement with the experimental values over the whole temperature and composition range.

Jan 1, 1992

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By Shuo Wang, Yu Wang, Bing Xie, Rui Tang, Hong-Yi Li, Kun Wen

"During present converter vanadium extraction process, phosphorus could not be removed from hot metal due to absence of CaO in slag though it is an efficient way for vanadium extraction. In order to improve the phosphorus remove and produce CaO-containing vanadium slag, which could be directly used in subsequent roasting process, during the converter vanadium extraction process, lime dissolution in FeOx-Si02-V203-Ti02 slag was investigated by using a rotating cylinder technique and the slag-lime interface was characterized by SEM/EDS. Results showed that changes in the slag chemistry and phase compositions during the lime dissolution process were similar to that in CaO-Si02-FeOx based slag during the BOF process. The V and Ti in the slag were expected to diffuse into the lattice of2CaO·Si02 solid solution, which formed a rather thinner layer in thickness at the slag-lime interface than that in BOF process, leading to improvement of lime dissolution in the slag.IntroductionVanadium is important material that widely applied in industries. The traditional technique to extract vanadium was to leach vanadium after sodium salt roasting. However, the sodium salt roasting process has several problems including lower yielding rate[!] and environmental pollution[2]. Therefore, the more environment-friendly technique of calcium roasting[3-4] was proposed. In order to increase roasting efficiency of vanadium slag, it is essential to study the dissolution/reaction mechanism between lime and vanadium slag. Many investigations about the dissolution reaction of lime in molten slag have been carried out from the standpoints of rapid slagging to De-Pin steelmaking process[5-6]. However, their studies were focused on BOF slag and the reaction mechanism between solid lime and slag containing vanadium has not been reported yet. In present work, the dissolution process was studied with rotating cylinder technique and the reaction interfaces were observed and analyzed by SEM/EDS to elucidate the dissolution mechanism of lime in vanadium slag. This work was supported by National Natural Science Foundation of China No. 51090382."

Jan 1, 2013

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988

By Ygor Macabu de Moraes, Jean Igor Margem, Carolina Gomes Dias Ribeiro, Frederico Muylaert Margem, Sergio Neves Monteiro, João Batista Vasconcelos

A natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. The objective of this work was then to assess the Izod impact resistance of polymeric composites reinforced with one or two layers of batt malva and jute fibers. The results showed are markable increase in the notch toughness with increasing layers of mauve blankets and jute.This can be attributed to a preferential debonding of the fiber/matrix interface, which contributes to an elevated absorbed energy.

Mar 1, 2017

By Shangshu Li, Xin Li, Xionggang Lu, Xingli Zou, Kai Zheng, Yinshuai Wang

Ti5Si3/TiC composite has been successfully prepared from the titanium-rich slag/SiO2/C mixtures precursors by an electrochemical process. The electrochemical production process was carried out in molten CaCl2 salt at 1000 °C and 3.8 V. A pressed cylindrical pellet of titanium-rich slag/SiO2/C mixtures served as a cathode, and a solid oxide oxygen-ion-conducting membrane (SOM) tube filled with carbon-saturated liquid tin acted as an anode. The phase transformation of the cathode pellets during electrolysis process was investigated, the microstructure of the obtained products was characterized. It is found that the reaction pathways can be divided into three main stages during the electro-reduction process. The first stage is the generation of calcium compound, the second stage is the electrochemical reduction of the compound, and the third stage is the formation of Ti5Si3/TiC composite. The prepared Ti5Si3/TiC composite exhibits homogenous and nodular particle morphology.

Mar 1, 2018

By Dong-sheng Li, Hong-ming Long, Tie-jun Chun, Chao Ning, Zhen Wang

Iron ore sintering is an essential process in modern iron and steel production. It has the largest emission of the PM (particulate matter) in the iron and steel industry, accounting for about 40% of the total emission. The physical and chemical properties of PM 10 and PM 2.5 in the iron ore sintering were introduced, and the research development of PM emission reduction was also summarized. The potential future development of PM emission reduction by chemical agglomeration and capture in the iron ore sintering process was also carried out. The interface chemistry relationships between PM and polymer, such as sodium carboxy methyl cellulose (CMC) and polyacrylamide (PAM), in agglomerates were also investi- gated in this paper. It is signi ficant to reveal the characteristics of PM and develop the emission reduction technology of PM for the cleaner production of iron ore sintering.

Mar 1, 2018

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By Xiangru Chen, Qijie Zhai, Haicheng Li, Chao Yang, Zhang Wei

The Nb-rich phase generated by the addition of trace amounts of Nb(<0.1wt%) \ and the effects of different content of Nb on the morphology and distribution of graphite in ductile iron were studied in this paper. The results showed that when the content of niobium less than 0.1wt%, the two-dimensional morphology of Nb-rich phase existed in microalloyed ductile iron were mainly regular pattern such as square, triangle, polygon etc. Besides, Nb-rich phase in large size distributed in the matrix with a certain distance from graphite. With the increasing amount of niobium, the dispersion degree of graphite diameter, average diameter and roundness increased slightly, and the number of graphite decreased slightly.

Jan 1, 2015

By G. E. Lagos

This paper analyses the scope and instruments employed by the Basel Convention for regulating the transboundary movement of hazardous wastes, the present and projected hazardous waste regulations of Chile, reviews the Chilean import/export trade of wastes of the period 1985-1995, and discusses, the influence that the Basel Convention has had on mining trade, its perceived benefits and costs, and possible effects on Chile&apos;s trade of the application of the Convention&apos;s Decision III/l. There is no quantitative estimation as to the effect of the Convention on the general volume of imported or exported materials destined for recovery, recycling, reclamation, or reuse. All recycling imports, with the possible exception of residues of petroleum oil, which occurred during the decade 1985-1995, can be classified tentatively as non hazardous. The entry into force of the Convention has had several effects on Chile&apos;s trade. It has brought home the need to have a comprehensive hazardous waste legislation, it has been a base for applying import restrictions, which in all likelihood, would .have otherwise not been applied, The benefits and costs of this import restriction, as well as those of the multilateral export ban are analyzed.

Jan 1, 1999

By E. James Quinn

Solvent extraction technology using EHEHPA (2-ethylhexyl phosphonic acid, 2-ethyhexyl mono ester) is the norm for industrial separations of rare earth elements. This process has some shortcomings, including a large number of stages compared to most SX processes and high acid requirement for stripping of the heavy rare earths. In this work, we examine a number of alternative mixed solvent extraction systems: (i) Mixtures of organophosphonic and phosphinic acids such as EHEHPA/Cyanex 272 or Cyanex 572; (ii) Ionic liquid mixtures of EHEHPA with quaternary ammonium chloride (Aliquat 336); and (iii) Mixtures of carboxylic acids for yttrium/lanthanide separations. We discuss and compare the efficacy of these systems with reference to the Nd/Sm separation, which is of industrial significance. Based on the extraction chemistry and the use of modelling tools to define the counter-current solvent extraction circuit, we present a techno-economic analysis of a separation plant and discuss the impact of various solvent systems on the capital expenditure (CAPEX) and operating costs (OPEX).

By Stephen R. Brown

Current conditions in the copper market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new production capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to minimize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by .the skill levels of the operators :and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: interactive animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-specific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term retention than more traditional learning methods.

Jan 1, 1999

By J. Van Boven

The Hoboken plant has continued the program, started in 1973, for monitoring the impact of processes on the environment. Progressive improve¬ments including new installations and equipment have been commissioned resulting in reduced emissions of lead in air. The Hoboken Smelter now fully complies with regulation and observes a yearly mean value of less than 2 micrograms Pb per cubic meter of air in the vicinity of the plant. In addition a new central water-treatment installation permits the discharge of waste water to the River Schelde in accordance with present day regulations. Mention is made of methods used to measure the emissions and immissions at the plant. Results of modifications and new installations recently commissioned are discussed.

Jan 1, 1983

By Tzu-Chien Lin, Jack Tsai, Ming-Yu Lin, Der-Ray Huang, Jiin-Sen Chen, Jing-Xuan Lin

"In this paper, some DVD-R discs have been selected for long time light exposure test and high temperature and humidity test. Generally, recordable media under long time light exposure maybe be defected seriously. If we use Jitter value 8% as a reference to determine the life time of DVD-R samples, some discs defect after 5 hours of light exposure while some discs can endure over 25 hours. Also if we use reflectivity 45% to determine the life time, some discs defect after 30 hours light exposure while some discs can endure over 40 hours. From our results, the good samples show good characteristics of PI error. The absorption spectrum of recordable media is a good reference to justify the quality of dye media. These results can be used to estimate the life time of recordable discs.IntroductionIn general, the life time of DVD-R with a layer of organic dye recording layer is required for preservation in decades. In addition to optical characteristics and thermal properties, we still need to consider the stability of the dye in recording media. The presentation of the color on organic dye is not only related to the material's property but also related to the light exposure. In this study, we focus on the absorption characteristics and reflectivity of organic dye in optical recording layer after light exposure. The optical properties of discs depend on the functional groups and molecular structure [1]. According to ""DVD Specifications for Recordable Disc (DVD- R)"", the reflectivity should higher than 40%. From measured reflectivity, we can confirm that the important issue is whether dye be affected by light exposure or not. Because each specific functional group absorbs the specific spectrum, we can check the characteristics of functional groups from their UV/Visible Spectra. We also use High-performance liquid chromatography (HPLC) to detect the different components of dye on the recording layer [2]. The jitter value test is to test the error cause by digital signal of recording media. If we use jitter value 8% as a reference to determine the life time of DVD-R samples, the purpose of this study is to investigate the jitter values of recording media after high light exposure and high temperature/humidity test. The results of these test will be helpful for the development of long-life optical storage media."

Jan 1, 2012