Search Documents

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Carlos Ortiz

The Huelva Flash Smelting Furnace was commissioned in September 1975. The Smelter and the Acid Plant were expanded in 1995 to their present capacity of 300,000 tpa new copper equivalent and one million tonnes of concentrate per year. During these years of operational experience, most of the initial practices have been reviewed, process control has drastically improved and main process equipment has been modernised. The fourth Flash Furnace campaign lasted 9 years (1995-2004) during which 8 million tonnes of concentrate were smelted. Increasing sulphur content in concentrates and new environmental requirements imply new challenges for smelters to keep production and operation costs down. This paper is an overview of the modifications and improvements carried out in the 2007 general shutdown in Smelter and Acid Plants. Al

Jan 1, 2008

By Afshin Sadri

Acousto Ultrasonic-Echo (AU-E) is a technique developed to provide accurate measurements of the refractory lining wear in operating smelters based on the principles of stress wave propagation. The objective of the system is to provide feedback for the continuous optimization of the overall smelter operation. In some cases, the AU-E refractory lining measurements have allowed clients to extend their smelter campaigns and operate safely for several years beyond their planned reline schedule. In other cases, AU-E results inform clients of serious issues within their furnace allowing them to shut down their smelters ahead of predicted failures and possible disasters. This paper presents the results of several smelter AU-E inspections of the hearth and sidewall. These case studies demonstrate how the AU-E results were used to positively affect the smelter operation.

By P. M. Tyroler

Inco operates a hydrometallurgical plant to treat the residue from the pressure carbonylation process. The main constituent in the residue is cop¬per. The residue is leached under pressure in an acid sulphate solution in two stages and the copper is recovered via electrowinning. The electrowinning tankhouse is fully integrated into the overall plant flowsheet as spent elect¬rolyte is required in upstream leaching steps. In recent years, the amount of residue had increased and copper removal capacity became the rate limiting factor for the entire plant. Consequently, a major program was undertaken to upgrade the tankhouse with regards to capacity, efficiency, cathode quality, working environment and structual integrity and appearance. This paper will describe current facilities and operation, and detail progress in our up¬grading efforts.

Jan 1, 1987

By Jean P. Murray

The extractive metallurgical industry is a major consumer of high-temperature process heat. It is, consequently, a major contributor of C02 emissions and other greenhouse gases derived from the combustion of fossil fuels for heat and electricity generation, or from the process itself. These emissions can be substantially reduced by replacing fossil fuels with solar energy as the source of process heat. Concentrated solar radiation can supply a large amount of thermal energy to endothermic reactions at temperatures exceeding 2000 K. Another potential for C02 emission reduction exists as well. Thermodynamically, the total amount of energy required for metal production at any given temperature is the enthalpy change of the reaction, AH. Of this total, an amount equal to the Gibbs free energy AG must be supplied as high quality energy in the form of electrical work or by using a reducing agent. Many conventional metallurgical electrolytic processes and reducing furnaces are unable to add only the thermodynamically required electricaVchemical energy due to process inefficiencies. Electrical work in excess of AG for the reaction may be used to supply process heat, or excess chemical reducing agent burned to supply process heat. Besides the thermodynamic and economic drawback, this inefficiency results in excess C02 emissions derived from the combustion of fossil fuels. With these practices, energy becomes an important cost element of the metal produced. Highly-concentrated solar energy has the demonstrated potential to separate these two forms of process energies, allowing the addition of only the thermodynamically required high-quality energy while high-temperature solar process heat is provided to the reactor. Examples of metal oxide reduction processes that have been studied experimentally in solar furnaces include the production of Fe, Al, AI/Si alloy, Mg, Zn, Tic, Sic, CaC2, TIN, Si3N4, and AIN by carbothermic reduction of their oxides, and the high-temperature solar- electrothermal reduction of ZnO.

Jan 1, 1999

By P .. R. Ammann

A two-stage pyrometallurgical process has been developed for the recovery of copper (and other non-ferrous metals) from copper smelter slags. All types of slags, including highly oxidized, converter-type slags, are cleaned in an electric furnace which employs mechanical mixers to promote magnetite reduction and copper extraction at high rates. In a 10-ton pilot furnace, it has been demonstrated that slags can be cleaned to 0.2-0.3 per cent copper with economically acceptable usage of raw materials and energy; copper is recovered as a high-grade matte. Pilot plant data have been scaled up to a commercial furnace and engineering designs have been made for a furnace to treat 60 tons per hour of slag from a Noranda Reactor and the associated converters. Plans are being formulated for the construction of a prototype slag cleaning furnace.

Jan 1, 1976

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By Alvear G. R. F. Flores

It is now 35 years since the organization of the first sulfide smelting conference in 1983. Since then, the smelting base metals industry has experienced several changes driven by the necessity to improve economic, operational and environmental performances and resource efficiency and meet the increasing market demand for metals. In this continuously challenging environment, it is relevant to recognize which are the main challenges that the industry will face in the coming years and critically address our preparedness to respond to them. This analysis have to consider not only the effort required from the fundamental research and technology aspects but also how these pillars interact with the drivers behind the base metals industry. This paper discusses some relevant aspects required to continue developing the base metal industry focusing on copper. Aspects such as the need to supporting the generation of fundamental metallurgical knowledge, acquisition and proper use of data with advanced analytics methods, technological innovation to develop sustainable process flowsheet are discussed with emphasis on efforts conducted by Aurubis.

By Ying Wang, Min Chen, Cuihuan Huang, Haohua Deng, Nan Wang, Ming Chen

Adding limestone directly into converter is considered to be favorable to energy conservation and emission reduction by transferring the decomposition reaction of limestone from the shaft or rotary kiln to the converter. In this paper, the kinetics of limestone decomposing in early converter slag was studied at 1300–1400 °C, and the effects of slag temperature and stirring speed introduced to the slag bath were examined. The kinetic results based on shrinking core model analysis showed that the limestone decomposition was a mixed rate control of chemical reaction and heat conduction through the lime layer, which could be promoted at higher slag temperature by supplying more heat to the converter bath. In addition, the chemical reaction rate constant and effective thermal conductivity were determined.

Mar 1, 2018

By J. T. I. Poijärvi

Outokumpu Harjavalta Metals Oy operates copper and nickel smelters, three sulphuric acid plants and nickel refinery at Harjavalta and copper refinery and precious metal plant at Pori. The by-products of these plants are presented in this paper. The by-products of the smelters include products from slag cleaning of flash smelting furnaces and converters, flue dusts and smelter off-gases. Weak acid and sludges from cleaning of smelter off-gases and acids are the by-products of the acid plants. The by-products out of the copper refinery are crystallized metal sulphates and sludges from electrolyte purification, on which a co-production process of the copper tankhouse is based. The main by-products of the precious metals plant are products from anode slime treatment and platinum metal group concentrates in the recovery of precious metals. Sludges from nickel matte leaching and precipitates from solution purification are the by-products of the nickel refinery. The formation, treatment and processing as well as the research work done for the utilization instead of dumping of the by-products in the production of copper and nickel will also be discussed in this paper.

Jan 1, 1995

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Robert L. Stephens

"It can be argued that one of the most important property of any material is cost, since this property detennines the applications for which a material can be considered. Despite growing demand and production for commodity metals such as copper, nickel, zinc, lead, and tin, the cost of these metals has been steadily decreasing in real terms. The only way that metal miners and producers can remain financially viable in the long term is by continuing to lower their cost curve through the implementation of new metals production technologies. This paper reviews technological developments in the production of copper, nickel, zinc, lead, and tin that have or threaten to redefine the cost curves for these metals.DisclaimerThe opinions expressed in this paper the author's, and are not necessarily those held by the author's employer, Cominco Ltd.IntroductionThis meeting will discuss many novel technologies and processes for producing metals and materials with specific properties that will enhance the applications ranges for the material or will allow entirely new applications to be developed. However, in every real-world case, the cost of the new material or process is an important property that determines which applications the material or process can be used in. Other properties that are important depend on the applications.A recent press report (1) discussing the potential replacement of aluminum radiators with copper radiators in pickup trucks and sport utility vehicles provides an interesting example to reinforce the importance of cost in materials selection. In this case, the displacement of aluminum by copper is being considered because of the more favorable heat dissipation characteristics of copper. Heat dissipation has become more important due to the development of hotter-burning V-8 and V-6 engines. For this application, engineers also consider cost, weight, size, durability, and manufacturing process. The report stated that the development by the International Copper Association (ICA) of the ""CuproBraze"" manufacturing process for heat transfer products was an important development. This technology produces 845 radiators that weigh less, are more uniform in quality, and are potentially more compact. They are also expected to cost less in high production quantities than copper units produced in the past, last three to four times longer than soldered copper radiators, and the process also eliminates the use of lead solder from the manufacturing process."

Jan 1, 2000

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By Leon E. Laforest

An early commitment by Kidd Creek Mines Ltd. (formerly Texasgulf Canada) to follow a stringent environmental control programme from the initial stages of design and development of its metallurgical facilities in Timmins, Ontario, has resulted in the on-going attainment of extremely low levels of industrial waste emissions. This paper outlines the monitoring programme initiated and maintained by the company's environmental control section. Comparative results of environmental sampling for the periods before and after the copper smelter start-up are highlighted.

Jan 1, 1983

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004

By Corby G. Anderson

In the majority of industrial operations recovering gold and silver by hydrometallurgical means, cyanide is the predominant lixiviant. However, as an economic alternative, production of massive quantifies of silver chloride was done on an industrial scale in the nitrous-sulfuric acid pressure leaching of a refractory precious metals concentrate. This proven process required no cyanide. Thus, because of the large volumes encountered during day-to-day plant operation, the need for efficient and low cost methods of silver chloride precipitation, reduction and materials handling was mandatory. As such, this paper covers the evolution of plant scale precipitation, filtration, washing, reduction and control of silver chloride processing. As well, an in-depth description of the unique leaching system is included.

Jan 1, 1998

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011