Search Documents

By Sungdon Kim, Chuljoo Kim, Joonsoo Kim, Hosung Yoon

"This study was performed to establish the optimum leaching condition through the experiments for the oxidized roasting followed by leaching of fluorocarbonate rare earth mineral (bastnasite) using sulfuric acid, and to establish the optimum condition for the recovery of cerium by ion- sieve method from the leached solution of bastnasite. The optimum conditions for the sulfuric acid leaching by the oxidizing roasting of bastnasite concentrates are that the roasting temperature is 550 -600 °C, the roasting time is 2 hrs, the concentration of sulfuric acid is 6N, the leaching temperature is S0°C and the leaching time is 3 hrs. At this time, the leaching yield of total rare earth oxides in the leaching of bastnasite concentrates is about 91%. When cerium is recovered by ion-sieve method from the solution obtained by the sulfuric acid leaching of the roasted bastnasite, the optimum conditions are that the TREO(total rare earth oxide) of leached solution is below 70 g/l, the flow rate of leached solution is 9.6 ml/min and the ratio of height to diameter of resin packed in column is above 9. In these conditions, the recovery of cerium of yield 85% and purity 96% is possible.IntroductionThe rare earths are generally called to Lanthanides, which are totally 17 elements including Scandium of atomic number 21 and Yttrium of atomic number 39 in addition to 1 S elements from Lanthanum of atomic number 57 to Lutetium of atomic number 71. Since the separation to each element is very difficult because of their similar chemical properties, the rare earths were used as the mixed rare earths and the mischmetal without separating to each element. However, the high purity rare earths are recently produced commercially to each element so that they are used as the materials for high tech. industry such as electric and electronic materials, catalysts, optical materials, special alloy and 8Uperconductive materials, and their consumption is rapidly increasing. Therefore, the purpose of this study is firstly to prepare leached solution by using the series of process of the oxidation-roasting and leaching by sulfuric acid. Next, second purpose is the separation and recovery of cerium by ion-sieve method."

Jan 1, 1998

By Xiaobing Yang, Abhishek Lahiri, Animesh Jha

"In the FFC-Cambridge process, the cathodic dissociation of oxide and CO/CO2 production on carbon anode is the basis for metal production in a CaCl2 bath. By using an inert intermetallic anode, the CO2 evolution can be eliminated altogether with acceleration in the electro-reduction kinetics. At present the process suffers from slow reduction kinetics of TiO2 to Ti metal, which can be enhanced significantly by the incorporation of alkali species in the TiO2 pellet at the cathode and in the CaCl2 bath in the presence of an intermetallic inert anode. Nearly full metallization with greater than 99% of Ti metal containing 1500 ppm of oxygen is possible to achieve in less than 16 hours of electro-reduction. Analyses of phase composition and the microstructures morphology in fully metallized pellets revealed the presence of localized solidified Ti layer, indicating that fast reduction process also involved formation of liquid phase as middle stage reaction. In addition, in situ creation of porosity and maintain higher current level during electrolysis process were two key factors to fully reduction of TiO2.IntroductionDuring cathodic dissociation of TiO2 in a CaCl2 bath and anodic evolution of CO2 on a carbon anode, which is the basis for the FFC Cambridge process [1], the rate of metallization slows down due to the formation of CaTiO3 at the reaction interface. Calcium and alkaline earth perovskites are known for their poor electrical conductivity which adversely affects the overall electro-reduction. One of the ways to increase the porosity is via the addition of polyethylene precursors in the pellet or by directly starting from perovskite [2, 3]. The experimental evidences shown in the literature confirm although the speed of reaction increases, but a complete or near complete metallization is not possible by enhancing the in-situ porosity alone, as the insulating perovskite is very slow to decompose under the equilibrium that prevails in the cell. Plethoric evidences on carbon anode show with the current decrease gradually, and finally stabilize at a very low value between 0.2 and 0.4 A, which is a testimony of the presence of perovskite insulating barrier in the current path. Our aim in this paper is to demonstrate the mechanism of enhanced electro-reduction when alkali ions are present in the oxide pellet at cathode and in the bath. We also show for the first time the use of an intermetallic anode for Ti-metal production using the FFC Cambridge process."

Jan 1, 2009

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By Brian R. Green

Resin-in-pulp (RIP) technology has been developed for recovery of gold. It is now time to look forward to the potential for application of the technology to other situations. Some cases have been identified and have merited preliminary testwork. Four examples, which illustrate the potential of RIP, are dealt with in this paper. These include removal of metal-cyanides from pulps, recovery of manganese that is difficult to wash from filter cakes, recovery of nickel from low grade pulps, and recovery of zinc from process residues. The discussion includes descriptions of the problems, factors that affect the choice of resin, and factors that will affect the economics of the process.

Jan 1, 1998

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothemlic reduction, hydrometallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By F. J. Arriagada

Where gold is present in a finely disseminated form within sulfide particles, the porosity and surface area of the calcined material strongly influence leaching since they control the penetration of solution inside the gold-bearing grains. On the basis of a stability diagram for the Fe-O-S in the temperature range of 400 to 750aC, the expected sequence chemical transformations associated with the oxidation of pyrite is discus-sed. By using analytical techniques which include scanning electron microscopy, X-ray diffraction and BET gas adsorption, the chemical and structural changes experienced by auriferous pyrite-arsenopyrite concentrates and pure pyrite samples are studied under an oxidizing roasting atmosphere of com-position 80% N + 20% O2 in the temperature range of 450 to 750°C. The results indicate that as the roasting temperature increases, the surface area of the calcines decreases sharply after a maximum value attained at about 450-500°C. SEM micrographs show that the needle-shaped tips which characterize the surface of the oxide product become wider and the size of the pores between them is decreased when the roasting temperature is in-creased from 550 to 750°C. This effect suggests that the formation of a more "closed" hematite product at higher temperatures is due to sintering associated with a faster growth and crystallization of the oxide. A strong correlation is shown between increasing roasting temperature and increase in gold lost in cyanidation tailings, an effect which may be partly attributed to the loss in surface area of the calcines.

Jan 1, 1982

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Khalid Hattar, Alexander McGinnis, Buchheitm Thomas, Paul Kotula, Luke Brewer

"Understanding the effects of extensive radiation damage in structural metals provides necessary insight for predicting the performance of those metals considered for application in the extreme radiation environment. Predicting mechanical performance after long term radiation exposure is of great importance to extending the life of current nuclear reactors and for developing future materials for the next generation of reactors. A combination of finite element modeling, nanoindentation, and TEM characterization were used to rapidly determine the microstructure and mechanical properties influences of ion irradiation on a standard 3 l 6L stainless steel sample. The results of this study found that ion irradiation and small scale mechanical property testing can be used to characterize extensive levels of radiation damage structure, only when significant consideration is given to ion irradiation depth, surface roughness and polishing condition, the irradiation temperature, and many other experimental parameters.IntroductionFor either the success of next generation nuclear reactors or the extension of current nuclear reactors significantly beyond their designed lifetimes, research is needed into the degradation of the microstructure and mechanical properties governing the performance of the reactor alloys exposed to extreme environments. Although the exact dose and temperature of these nuclear reactor plans may vary, the cladding and other structural components will be exposed to greater dose and at elevated temperatures. To acco=odate these severe exposures, established cladding materials are being testing to longer exposure and new alloy compositions are being considered. [1-3] For neutron test facilities to reach 100 dpa level, exposure times often span several years, significantly limiting the down-select process of potential new materials for extreme radiation environments. Ion irradiation has been used as a technique to provide a look at the effect of irradiation damage on materials in a significantly shorter time frame. Previous work using proton irradiation provides a deep, broad, and relatively uniform defect profile compared to heavy ion irradiation; however, using this type of radiation still requires weeks to months to reach the 100 dpa level. [4] In this research, we investigated the feasibility of using heavy ion (nickel) irradiation and small scale mechanical testing to provide in a few days a first order screening technique for potential alloys that are being considered for advanced testing."

Jan 1, 2012

By Harsh Deep Chopra, Jason N. Armstrong, Susan Z. Hua

"Existence of anisotropic Curie temperature materials [E. R. Callen, Phys. Rev. 124, 1373 (1961); J. Appl. Phys. 32 S221 (1961)] is a longstanding prediction - materials that become paramagnetic at a lower temperature along certain crystal directions while remaining magnetically ordered in other directions up to a higher temperature. Validating Callen's theory, we show that all directions within the basal plane of monoclinic F e1Ss (pyrrhotite) single crystal remain ordered up to 603 K while the c-axis becomes paramagnetic at 225 K. Results prompt a re-evaluation of existing magnetic materials with a focus on magnetic characteristics along different crystal orientations above instead of below the ordering temperatures. Theoretical guidelines for identifying new materials with large anisotropy of Curie temperature are also given, and analysis protocol to characterize them in a self-consistent manner is discussed. Materials with such a large directional dependence of Curie temperature open the possibility for uniquely new devices and phenomena, including energy storage and spintronics devices.IntroductionThis paper is an overview of our recently published work on anisotropic Curie temperature materials [l]. As a background, ferromagnetic and ferrimagnetic materials are characterized by a critical temperature below which magnetic interactions prevail over thermal agitation, leading to the appearance of a spontaneous magnetization. Above this critical point, called the Curie temperature, thermal energy eventually overcomes magnetic interactions and the material becomes paramagnetic.It is less well known that the Curie temperature varies with the orientation of the crystal. In ordinary ferromagnets this orientation dependence of Curie temperature is negligible because of the vanishingly small ratio of anisotropy to exchange energy, i.e., the spherical or isotropic exchange term dominates. Thus Curie temperature in ordinary ferromagnets appears to be an isotropic property, and assigning it a single characteristic ordering temperature suffices. However, a 'small' difference is not equivalent to being the 'same', and under appropriate set of conditions the anisotropy of Curie temperature is predicted to become appreciable, as discussed in the following.In formulating the theory of 'anisotropic magnetization' [2, 3] E. R. Callen and H. B. Callen first discussed the ""interesting possibility"" of anisotropic Curie temperature [2] or ACT; Callen and Callen noted that it was W. J. Carr, Jr. who initially raised this question, and they discussed it in detail at the Conference on Magnetism and Magnetic Materials (NY, November 1960), see footnote on page 320 of Ref. [2]. Soon thereafter, E. R. Callen developed the theory underlying the anisotropy of Curie temperature and conditions conducive to its observation [4, 5]."

Jan 1, 2013

By Florian Kongoli

Non-ferrous smelting slags .can contain magnesia, which substantially increases the liquidus temperature. One option to counter this increase is to flux with calcia. In this work, experimental liquidus measurements including new measurements on industrial slags have been compared with a FACT-based thermodynamic model, which predicts the liquidus surface of multi-component iron silicate smelting slags containing both magnesia and calcia. The predictions, which agree well with experimental results, are summarized in both isothermal and non-isothermal diagrams to give a quantitative description of the liquidus surface.

Jan 1, 1998

By E. W. Lithgow

Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, x- ray amorphous materials. Minor constituents are hematite, gibbsite, olivine and enstatite. In the Ore Dressing plant the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock fragments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing.

Jan 1, 1993