Search Documents

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By Xiang Lan

A strain of Thiobacillus ferruuxidans No. 8 was isolated from the acidic mine water of an arsenopyrite deposit, South China. It has been found from the experimental results that the growth of bacteria was inhibited by flotation agents. The order of toxic effect of different flotation agents on the growth of Thiobacillus ferrooxidans is ethyl xanthate > butyat ammonium aerofloat > butyl xanthate ? isobutyt xauthate >? flother No. 2 oil. The bioteaching treatment of arsenic and antimony-bearing gold concentrate in Longshan mine, Hunan province, China, was influenced considerably by the presence of flotation agents. The possible causes of the influence of flotation agents were discussed and an improved method was suggested.

Jan 1, 1991

By Cynthia Belt

"Energy management is critical to aluminum processing given the high energy requirements of melting and processing aluminum. Energy costs have always been a high percentage of the total production costs within this industry. Energy management at many plants relied on better technology that many times required high capital. As carbon management has grown in importance and project payback becomes more critical, a larger view of a plant's process is required. This paper looks at the energy requirement due to current typical practices in overall product recovery, metal loss, utilization, and technology to understand potential methods of reducing overall energy within a plant and within the aluminum processing industry.IntroductionFor many companies that process aluminum, energy is a major portion of their costs that can surpass the cost oflabor. Aluminum processing can include secondary processing of scrap and prime aluminum into sows and/or molten aluminum or casting aluminum by various methods such as direct chill, continuous casting, low or high pressure casting, mold casting, and extrusions. In the case of this paper, we are considering only plants that include the melting process as a portion of their process. The process of melting aluminum takes energy. In most cases, the aluminum must then be heat treated one or more times. Post processing of the aluminum includes rolling mills used for making sheet, extrusion lines, and machining such as saw cuts, drilling, or surface finishes that all take additional energy.While these high energy costs directly affect the profits of the company, energy management within the metals industry is still not widespread. A co=on misconception is that the solution to high energy costs is high cost capital equipment. While state-of-the-art equipment can certainly improve energy efficiency, it is not the only solution. To obtain a truly energy efficient plant, several directions needs to be addressed through an energy management thought process with a wider scope. Impact on potential savings is possible through: product recovery, metal loss, utilization, and new technologies. An understanding of the potential costs and savings from these means is important. Several of these methods provide low cost approaches to saving energy.The background data used in this paper is not a random sample within aluminum processing but yearly averages from various plants in different aluminum processing industries. As is normal in this industry, the plants have been under different corporate management over the years with different strategies for energy management. This data is not meant to be accurate for the entire industry but to suggest areas for energy efficiency work."

Jan 1, 2012

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Baokuan Li, Qiang Wang, Zhu He

"A mathematical model has been developed to investigate the magnetohydrodynamic (MHD), thermal, and solidified behavior in electroslag remelting process. Based on the finite volume method, a multiphase coupling MHD approach is employed to investigate the droplet formation as well as movement in molten slag under the action of an alternating current. The VOF formulation is adopted for interface tracking. The electrical potential method is adopted for the electric current and magnetic field. The Electromagnetic force and Joule heating are recalculated at each time step and then is implemented in the momentum and energy equations as a source term, respectively. Moreover, solidification of the metal is described by an enthalpy-based formulation, while the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The model is used to investigate the effect of electrode tip shape on MHD, thermal, and solidified behavior and provide valuable information.IntroductionElectroslag remelting (ESR) process has been used widely to produce high-performance alloys dedicated to critical application, such as hot work tool steels, nickel base alloys, the manufacture of components in aerospace and landbased turbines, etc. Figure 1 shows a schematic diagram of ESR process including a consumable electrode, a molten slag pool, a liquid metal pool, a solidified ingot, and a water-cooled mold. Alternating or direct current flows from the electrode to the water-cooled baseplate through the high resistivity calcium-fluoride-based molten slag which result in Joule heating and Electromagnetic force (EMF). Part of the Joule heating melts the electrode and the droplets travel through the slag and accumulate the liquid metal pool. The electrode is continuously advanced into the slag as it melts to build up an ingot of improved structure and composition by controlled solidification and chemical refinement. The metallurgical properties of the remelted ingot are really related to the solidification structure, which strongly depends on magnetohydrodynamic, thermal, and solidified behavior in the molten slag, liquid metal pool, and mushy zone."

Jan 1, 2014

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By J. B. Cocanour

Pioneering work at the U.S. Bureau of Mines (USBM) has produced a personal computer (PC)-based, software-driven video photometric color sensor for real time process control of metallurgical streams. The video photometer is an inexpensive optical sensor which operates in the visual area of the electromagnetic spectrum and collects color information through plastic optical fiber. The red, green, and blue (R/G/B) voltage components of the color video signal are digitized and characterized through software and then presented as the control variable for software-based proportional-integral-differential (PID) control. This sensor has been successfully employed in the control of a laboratory copper electrolytic circuit. With this sensor, copper solutions were analyzed on-line without the need for sample removal, dilution, mixing or reagent addition, thereby allowing for the real time control of the circuit.

Jan 1, 1994

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Fathi Habashi

In the past five years Cuba has been attempting to more than double its nickel production by constructing two new ammonia leaching plants. No metals are yet produced on commercial scale but a variety of oxides and sulfides. This report updates the Cuban nickel industry as a result of two visits : one at the invitation of the Cuban Ministry of Basic Industries in 1987 and the other as a consultant to the United Nations for the Cuban Laterite Project in 1989.

Jan 1, 1993

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By F. G. Prado

The technology for the extraction of zinc from zinc residues, such as zinc ashes, drosses and metallurgical flue dusts, by way of ammonium chloride solutions is well established, at least at the laboratory and bench scale levels. (3, 4) Zinc is soluble in ammonium chloride solutions in the form of zinc diammine chloride. Its solubility depends upon the concentrations and temperatures employed. The procedure and the equipment required are simple, and they can be applied either to small or large operations. As a by-product, zinc diammine chloride is produced with extremely low impurities in quantities which are stoichiometrically proportional to the zinc removed. The technology has been applied experimentally to galvanized steel residues. The dezincing results, including removal performance, energy and reagents required, and by-products are summarily presented in this paper.

Jan 1, 1992

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By M. I. Kalashnikova

Results of investigations concerning precipitation of heavy non-ferrous metals from solutions using precipitators based on elemental sulphur and lime with gypsum transfer to a separate product are given.

Jan 1, 2003

By Xiang Zhu

Xidagou is the largest waste water discharge channel of the Anshan Iron and Steel Complex (AISC) with average flow rate of 8000 cubic meters per hour, which is about 75% of the total effluent of the AISC. The waste water from Xidagou seriously polluted the Taizi River Basin. In order to meet the Chinese Class V Standard for Surface Water Discharge and the Standard for Recycled Industrial Water Reuse, with the aid of the World Bank, the AISC began the treatability studies in 1991. Based on the bench-scale test, the AISC carried out pilot-scale treatability studies on three different treatment processes and five different chemical coagulants for more than half a year in 1992. The study results show that the processes of primary sedimentation- chemical mixing and flocculation-secondary sedimentation-filtration can meet the requirement and that PFS and PAM are effective and economic chemical coagulants.

Jan 1, 1994

By Chunyang Guan, Jilai Xue, Jun Zhu, Qiaochu Liu

"Al-Sc Alloys have showed many advanced properties for a wide range of industrial application, which is usually produced using thermal reduction process. This work is aimed to develop an electrochemical process to make Al-Sc alloy using industrial Hall aluminum reduction cells. The experiments have been carried out in a lab cell where NaF/AlF3-Al2O3-LiF as electrolyte, Sc2O3 as raw material, and liquid aluminum as cathode were used at operating temperature of 950 °C. The resulting Al contained 0.2 - 0.5 wt.% Sc that is the common range in its content for advanced applications. However, a small fraction of Sc was found from thermal reduction at Al melts interface. SEM-EDS and ICP-AES analysis showed a uniformed distribution of Sc at varying locations of the Al-Sc alloy sample. In addition, a higher Sc content in Al-Sc alloy can be obtained with introducing ultrasound through the cathode than that without it.IntroductionIn recent years, scandium has been investigated as an alloying element for aluminum alloys. With addition of a small amount of Sc, Al alloys can improve the strength, weld ability, resistance to re-crystallization and corrosion resistance [1-3]. Due to their advanced properties and potential applications, the demand for Al-Sc alloys will increase in the future. However, the difficulties in reduction technologies and the high costs in production process may limit their expansion in application areas.The current major method of producing Al-Sc alloys is to mix Sc into Al by melting Al-Sc master alloy. This alloying process has several technical problems, such as easy segregating and heavy burning loss, etc. The price of Sc metal or starting material is also high, so the mixing process is an expensive alloying method. Molten salt electrolysis is alternative method to prepare RE metal and RE alloys [4, 5]. It also can reduce the segregation of alloying elements. Sc2O3 is an ideal material as raw material with low price and decomposition voltage. Some work has proved that Al-Sc alloys can be obtained by electrolysis Sc2O3 directly in cryolite [6-8], or CaCl2 molten salt [9]."

Jan 1, 2012

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996