Search Documents

By Mansoor Barati, Yindong Yang, Yonggang Wei, Bo Li, Alexander McLean

Reduction roasting followed by magnetic separation is an important method for treating laterite nickel ores. In this work, garnierite type laterite ore from Yunnan province in China was reduced by methane under different conditions followed by magnetic separation to obtain the ferronickel concentrate. The phase and microstructure transformations of garnierite in the reduction process were investigated using XRD and SEM-EDS. The experimental results showed that reduction temperature from 873 to 1173 K had only a small effect on content and recovery of nickel and iron. The content and recovery of nickel and iron in the concentrates increased slightly with prolonging reduction time. In addition, the nickel and iron content decreased with increasing methane concentration, but the recovery of nickel and iron increases. A decrease in the iron content and recovery were observed when the dosage of sodium sulfate varied from 5 to 20% at a temperature of 1073 K and reducing time of 90 min, while the nickel content and recovery gradually increased.

Mar 1, 2018

By Huaqing Xie, Qingbo Yu, Qin Qin

A novel sorption-enhanced steam reforming (SESR) process of hot coke oven gas (HCOG) was proposed for tar removal and H2 amplification, and was studied with the comparison of conventional steam reforming (SCR) process. Both of the processes could remove tar effectively and improve the H2 amount in the COG obviously. For CSR process, after the temperature and the S/HCOG ratio reached 700 °C and 2.4 respectively, the H2 amplification factor kept 4.30 around, with its concentration less than 75%. However, for SESR process, the H2 amount and concentration get improved further, with the optimal temperature moving toward low temperature. At 600 °C and the S/HCOG ratio of 2.4, the H2 amplification factor and concentration could reach 4.91 and 97.55% respectively when the CaO/C ratio was 2.0. Under the respective optimal reforming conditions of the two processes, the energy consumption of the SESR process was lower than that of CSR process.

Mar 1, 2018

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li, Yang Xu

Perovskite easily forms during sintering of vanadium titanium magnetite (VTM) and is unfavorable for the following blast furnace. Steelmaking can concomitantly produce a great quantity of oxidized scale composed mainly of FeO and Fe3O4. Calcium ferrite (CaOFe2O3, CF) can be formed by oxidized scale with lime in air atmosphere and then added to the VTM during sintering. X-ray diffraction (XRD) results indicated that perovskite is not generated at low temperature but only when the temperature increases to 1473 K in the CF–TiO2 system. Therefore, VTM sintering can be performed with a low-temperature process with doping of CF. Perovskite formation is mainly divided into two steps. First, CF melts and produces CaO. TiO2 and CaO then combine to produce perovskite. This paper also discussed the reaction mechanism of CaO–Fe2O3–TiO2 ternary system to compare the generation routes of perovskite.

Mar 1, 2018

By S. Chama, P. Chishimba, Tina Chanda Phiri, J. Machona, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

The investigation focuses on leaching of copper (2 wt%), cobalt (0.5 wt%) and iron (2.4 wt%) from complex tailings material from the Democratic Republic of Congo. The highest recovery of copper and cobalt into the leach solution were 78 and 10%, respectively, under direct leaching with sulphuric acid. Higher recoveries (90% for copper and 96% for cobalt) were attained when the material was pre-reduced with coal for 1.5 h in the temperature range of 700–950 °C. The increased recoveries were due to metallisation of all the copper and cobalt which is in the silicate matrix. The effects of pre-reduction temperature and sample to carbon weight ratios were analysed and found to be important in; (i) achieving high recoveries of copper and cobalt and (ii) decreasing the amount of iron in the leach solution. The samples were characterised by atomic absorption spectroscopy and scanning electron microscopy (SEM) techniques.

Mar 1, 2017

By Wei-Tong Du, Zheng-Lei Guo, Yu Wang, Shu-Chao Wang

The influence of bottom blowing a CO2–O2 mixture on the bath temperature of a vanadium extraction converter was studied by using the characteristics of CO2 with weak oxidizing. It was studied in two aspects: oxygen content and temperature. The experiments showed, when the ratio of the mixture of CO2–O2 was 2:8 at 1300 °C, the bottom blowing of the converter inhibited the heating up of the hot metal, thus keeping the temperature below the carbon vanadium transition temperature. At 1360 °C, the sensible heat absorption by CO2 was 1.44 times that absorbed by O2 per mole. Meanwhile, at 1300 °C, 20% CO2 released the chemical heat of 13.58 kJ. So with the increase of the CO2 ratio, the bath temperature was reduced. The research showed that the bottom blowing of a CO2–O2 mixture had an advantageous effect by decreasing the temperature of the vanadium extraction converter.

Mar 1, 2018

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Qiang Guo, Zongliang Zuo, Mengqi Wei, Qingbo Yu, Qin Qin

Activated carbons, derived from waste ion-exchange resin by CO2 physical activation, were applied to separate CO2 from flue gas against global warming. The BET specific surface areas of activated carbons at different activation temperatures and times were investigated. The CO2 adsorption capacity was tested under non-isothermal and isothermal conditions. The experimental results show that when keeping the activation temperature constant, the specific surface area increases firstly and then decreases with increasing activation time. For the given activation time, the specific surface area rises firstly and then declines with increasing activation temperature. The adsorption capacity decreases with increasing temperature. The maximum adsorption capacity is 51.46 mg/g under the condition of 298 K and pure CO2. Fractional order kinetic model is the best one to describe the kinetics of CO2 adsorption. The activated carbons show the potential to be an effective adsorbent for the removal of CO2 from flue gas.

Mar 1, 2018

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-9 (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 160' C for 1 h in a pressure vessel dissolved over 95 pct of the PGM from virgin catalysts and over 90 pct from used pellet catalysts. Over 85 pct of the PGM was dissolved from used monolith catalysts when a third leaching step was added. PGM concentrates as metallic powder containing over 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 250' C and used catalyst to 275" C for 1 h. The solution after heating contained primarily sodium carbonate from cyanide decomposition and less than 0.2 ppm total cyanide.

Jan 1, 1993

By O. G. Rivera, R. D. Moser, P. G. Allison, W. R. Whittington, P. Rivera-Soto, Z. McClelland, D. Francis

This research examined the evolving microstructure of quasi-static and dynamically loaded fully annealed metastable 301 austenitic stainless steel (SS). Experiments were performed to an interrupted strain value of 20% and to failure using a tension Kolsky bar (1000/s) and an electromechanical load frame (0.001/s). Electron Backscatter Diffraction (EBSD) identified the microstructural evolution from the as-received condition to the 20% strain level for the high and low rate interrupted samples. This material achieved over 60% elongation to failure with increasing strength as strain rate increased, as expected. Fractography analysis using SEM showed particles in the microstructure and a ductile failure mode. The 301 SS exhibited a greater amount of phase transformation from parent austenite to -martensite at the dynamic strain rate when compared to the quasi-static strain rate during the interrupted experiments. This result is indicative of the increased propensity for austenite to -martensite phase transformations at the high strain rate.

Jan 1, 2016

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By S. L. Pohlman

Physical characteristics of possible importance in the acid leaching of Chrysocolla have been evaluated. Surface area studies and pore size distribution indicate: 1) a large surface area (350 m /gm); 2) an average pore size of 13 or 16 Å , depending upon use of the adsorption, or desorption, branch of the Type IV isotherm in the evaluation; ) the presence of a significant fraction of pores of size less than 15 Å determined by the accumulation surface area method. The initial structure is micro- crystalline on the basis of x-ray powder patterns; the silica leach residue is amorphous and has only 24 m2 /gm surface area, and loses integrity when dry. However, readsorption of copper onto the wet leach residue gives a product with integrity and 100 m2 /gm surface area. Visual observation of the leach residues supports evidence of a non-protective diffusion mechanism of leaching which is well correlated by the shrinking core model previously presented.

Jan 1, 1976

By R. Padilla, M. C. Ruiz

Arsenic, antimony and bismuth are commonly found in copper concentrates usually as the minerals enargite, stibnite and bismuthinite, respectively. Concentrates having high levels of arsenic and antimony must be pretreated before smelting. Roasting is the preferred method for removing these toxic impurities from concentrates; However, the removal of As, Sb and Bi in oxidizing roasting by volatilization may not be complete due to the slow reaction rates at 500- 700 °C. Oxidizing/volatilization data were obtained from pure mineral mixtures and from arsenic rich copper concentrate. The reaction mechanism for the volatilization of arsenic and antimony were discussed. Near 100% As and over 95% Sb volatilized in the oxidation of a mixture of pure minerals at 700 °C, 1% oxygen, while over 95% As, and 35% Sb volatilized at 600 °C in 1% oxygen atmosphere when using a copper concentrate containing 3.51% As, 0.14% Sb, and 0.01% Bi. Bismuth did not volatilize.

Jan 1, 2015

By R. Padilla

Enargite (Cu3AsS4) occurs normally associated with copper sulfides, mainly chalcopyrite. When the enargite content in chalcopyrite concentrates is high, direct smelting of the concentrate presents problems related to environmental pollution and contamination of the final metallic copper. Leaching processes are viable alternatives to treat copper concentrates with high content of enargite. Consequently, in this paper, the pressure leaching of enargite in sulfuric acid-oxygen system is discussed. The leaching rate was studied in the range 160 to 220 °C and partial pressures of oxygen of 74 to 200 psi. The enargite dissolution increased substantially with temperature increase. Complete dissolution of enargite was obtained at 220°C, and 100 psi of oxygen pressure in 90 min. The shrinking core model controlled by surface reaction was used to analyze the kinetics of enargite dissolution. Activation energy of 70 kJ/mol was obtained for the temperature range 160 to 220 oC.

Jan 1, 2008

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Manman Lu, Tao Jiang

Acid wastewater containing toxic metal ions has become increasingly important global environmental concern and lead (Pb) is one of the prime toxic heavy metal ions. Humic acid (HA), a kind of natural organic matter, has been proventohaveagreatadsorptioncapacityformetalcations(Pb2+,Cu2+,etc.).Our previous study has verified that HA has excellent adsorbing ability on vanadium titanium-bearing magnetite(VTM) particles. In this study, VTM-HA complex magneticparticles werepreparedfor removing Pb(II)fromacidwastewater,which could be easily recycled by magnetic separation. The effects of pH value, ionic strength and VTM-HA concentration on the removal ratio of Pb(II) were deter- mined by isothermal adsorption tests. The results indicated that Pb(II) adsorption was subject topHand ionic strength. When initial Pb(II) concentration is 100 mg/ L, the residual concentration and removal ratio of Pb(II) reach 0.17 mg/L and 99.83%, respectively, which are much lower than the discharge standard. (cid:1) (cid:1)

Mar 1, 2018

By Fangqing Yin, Qingyu Deng, Zhengfeng Qu, Mengjun Hu, Meilong Hu

Titanium bearing blast furnace slag, which contains 20%-30% TiO2, is a valuable secondary titanium resource. Based on the thermodynamics calculation effect of the temperature on the reduction of the slag in vacuum were studied at certain vacuum degrees. The results show that magnesium vapor and silicon monoxide vapor can be obtained at the condition of high temperature and low pressure. The purity of TiC increases with temperature increasing. When the temperature arrives at 1623K TiC can be obtained besides the reductant carbon. XRD result of the powder collected from the furnace cover show that magnesium and silicon in the titanium bearing BF slag leave the slag system during carbothermal reduction in vacuum. From the above it can be concluded that TiC can be obtained from the titanium bearing BF slag and silicon and titanium in the slag can be separated by carbothermal reduction in vacuum and acid leaching.

Jan 1, 2016

By Chao Zhang, Jian Guo, Chaoquan Yao, Leige Xia, Xinyu Li, Jianliang Zhang

In this research, analytical reagents were used for the sintering experiments. And the sinters were using X-ray diffraction, scanning electron microscope and mineralogical microscope analysis to study the effect mechanism of manganese on the silico-ferrite of calcium and aluminum (SFCA) bonding phase formation during the sintering process. The results indicated that the increasing content of manganese would greatly reduce the content of SFCA, and promote the formation of calcium aluminum silicate and the amount of pores and cracks. The existence of manganese inhibited the silicon form into the SFCA and a great deal of Fe2O3 was participated in the crystal transition to Fe3O4. When the ratio of the added manganese was less than 3% in the mixing, the calcium ferrite was in substantially interleaving corrosion with hematite and magnetite. Both the porosity and silicate glass phase content were low simultaneously, which contributed to the sintering production.

Jan 1, 2015

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By Baozhong Ma, Chengyan Wang, Yongqiang Chen, Peng Xing

This paper introduces an oxygen-enriched flash smelting (OFS) process for lead smelting. Compared with the bath smelting, OFS has many advantages, including wide adaptability, high yield, low energy consumption, little uncontrolled emission, and considerable metals recoveries. Test results showed that increasing CaO could effectively reduce lead content in the slag, and the appropriate mass ratios of FeO-to-SiO2 and CaO-to-SiO2 were 1.15 and 0.6, respectively. The testing and commissioning indicated when OFS was used to treat material containing 30% of lead, the residual lead in slag could decrease to 4–10%. Furthermore, after zinc volatilization using an ore-smelting electric furnace, contents of lead, zinc, silver, gold and copper in the final slag were below 2%, 2%, 6 g/L, 0.1 g/L and 1%, respectively. The total recoveries of lead, zinc, silver, gold, copper and sulfur were above 98, 90, 99.5, 99.5, 85 and 98%, respectively.

Mar 1, 2018