Search Documents

By G. Fazel Jahromi

Enargite, known as one of the major arsenic containing copper minerals, with approximately 19% arsenic, introduces challenges to typical processing options. In most hydrometallurgical processing methods, arsenic remediation occurs after the copper recovery in an autoclave or in a stepwise neutralization process. In this study, the in situ precipitation of scorodite was investigated during an atmospheric leaching process in the presence of carbon-based catalysts and chloride media. The effective parameters of initial ferric addition, temperature, catalyst addition, and oxygen sparging rate were studied and the ferric behaviour was monitored during the scorodite precipitation. The most influential parameters on efficient scorodite precipitation are found to be: initial ferric addition, catalyst to concentrate ratio, and temperature. A 99% scorodite precipitation yield was achieved in this process.

By Myung Bae Kim, Yong Hack Lee, Woll Seung Lee

The Slag Fumer is the first Ausmelt furnace system adopted at the Onsan Refinery of Korea Zinc. This plant continuously treats the QSL lead smelting slag in the molten state. It has developed progressively since its first commissioning in October 1992 and has generated a confidence that it can produce an environmentally acceptable slag for use in cement manufacture and recover the zinc and lead in the slag as a fume oxide. This paper provides the operating experiences accumulated during the last eight years of operation, a summary of problems and solutions, and the current status of the operation.

Jan 1, 2000

By E. J. Peterson

Oil shale retorting induces mineral and chemical reactions to occur on the macroscopic and microscopic levels in the kerogen-bearing marlstone. The nature and extent of the reactions is dependent upon process variables such as maximum temperature, time at temperature, atmosphere, and raw shale composition. This report describes the investigation of the mineral, chemical, and trace element release properties of spent shales retrieved from an experimental in situ retort at Occidental Oil Shale, Inc. 's Logan Wash site in Garfield County, Colorado. Correlation between mineralogy of the spent materials and the mobility of major, minor, and trace elements are indicated, and relationships with important process parameters are discussed. The progress .of carbonate decomposition reactions and silicat ion reactions is indicative of the processing conditions experienced by the shale materials and influences the mobility of major, minor, and trace elements when the solids are contacted by water. Shale minerals that are exposed to the extreme conditions reached in underground retorting form high temperature product phases including akermanite-gehlenite and diopside-augite solid solutions, kalsilite, monticellite, and forsterite. The persistence of relatively thermally stable phases, such as quartz, orthoclase, and albite provide insight into the extremes of processing conditions experienced by the spent shales. Leachate compositions suggest that several trace elements, including vanadium, boron, fluoride, and arsenic are not rendered immobile by the formation of the high-temperature silicate produce phase akermanite-gehlenite.

Jan 1, 1981

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By Batric Pesic

Dissolution of gold with sodium bromate solutions of various compositions was studied by using a rotating disc technique. The role of bromide ion, acid and externally added bromine was examined. It was found that sodium bromate could not dissolve gold in the absence of either acid or bromide ion, or both. When acid was absent, no bromine necessary for gold dissolution could be produced. When bromide ion was absent, formation of soluble gold bromide species, AuBr,-, was not possible. Bromate concentration had a complex effect, and it was dependant on bromide ion concentration. For fixed initial bromide ion concentration, gold dissolution rate increased with sodium bramate concentration increase until certain level, beyond which further increase of bromate concentration decreased the gold dissolution rate. The negative effect of bromate was explained by the depletion of necessary bromide ion. Sulfuric acid concentration effect was a function of initially present bromine.

Jan 1, 1992

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By Saskia Duyvesteyn

For many applications in hydrometallurgy and water treatment it would be advantageous to use ion-exchange resins in stirred reactors. However, attrition of the resin may lead to significant losses of both resin and metal values and prevent water quality goals from being reached. We have studied the recovery of fine resin particles by froth flotation, using the model copper - Dow XFS4195 chelating resin system. As the functional group on the resin is a bis-picolylamine, the resin should be amenable to flotation by anionic collectors, such as sodium dodecylsulfate and sodium dodecylsulfonate. The kinetics of copper loading from dilute aqueous solutions in an agitated vessel were studied as a function of copper concentration, pH and resin bead size. The flotation of unloaded resin was investigated for different types of collector, collector concentration, conditioning time, and resin bead size. Potential applications are discussed.

Jan 1, 1995

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By David Dreisinger

The pressure oxidation of pyrite is an important hydrometallurgical technology, especially in the total oxidation of refractory gold ores and concentrates (gold is locked in the pyrite structure preventing direct cyanide recovery). It has been noticed in some commercial applications and benchscale studies that the leaching of pyrite may be slow and apparently can be inhibited by the presence of molten elemental sulfur in the leach pulp. The purpose of this study was to determine whether Ortho-Phenylene-Diamine (OPD) could be used as a surfactant or dispersant for sulfur in the pressure oxidation of pyrite. OPD has previously been shown to be useful for pressure leaching of zinc and copper sulfides at 150 C.In this work, the interfacial chemistry of sulfur was studied at temperatures of up to 190 C in the presence and absence of OPD and other surfactants. The contact angle between molten sulfur and pyrite was also measured. Finally, the impact of OPD on the kinetics of pyrite oxidation was measured in bench-scale pressure oxidation experiments. The essential finding of this study was that OPD lowers the interfacial tension between molten sulfur and acid solutions and increases the contact angle (reduces wetting) between molten sulfur and pyrite. The work of adhesion between sulfur and pyrite was reduced by more than an order of magnitude in the presence of OPD. In bench scale tests, addition of OPD was found to significantly accelerate the rate of oxidation of pyrite. Conveniently, it was found that OPD was also fully degraded during high temperature oxidation processes. No residual OPD was detected in solution or solid samples from the leach testing. OPD is recommended as a sulfur dispersant in the pressure oxidation of pyrite and/or elemental sulfur containing feeds.

Jan 1, 2003

By J. M. Demarthe

The recovery of minor metals from zinc concentrates is dependent on the process used for their treatment. The behaviour of gennanium and indium in pyrometallurgical processes such as the Imperial Smelting furnace or the cupola furnace is of practical importance. The .Anaconda process for the treatment of zinc leach residues is not well suited to the recovery of valuable minor metals, and new technologies must be studied. In this regard, a solvent extraction process, using Kelex 100, developed by Minenet Recherche for the recovery of gennanium from dilute sulphate leach solutions is described. Also, new hydranetallurgical techniques in chloride media can be applied to the purification and concentration of minor metals depending on the stability of their chloro-complexes and the valency of associated inpurities. A synthesis of methods is proposed to address the problems related to the recovery of valuable minor metals in the zinc industry.

Jan 1, 1990

By Michael Sheedy

Recoflo® ion exchange technology utilizes fine mesh resin beads, a fully packed resin bed, and counter-current regeneration. These unique features help to improve exchange kinetics, reduce regenerant consumption, and increase the concentration of strip solutions. Commercially, Recoflo technology has been extensively used in the following areas: the separation of strong mineral acids from dissolved metal salts, the purification, removal and recycle of dissolved metals in the surface finishing industries, and the production of high purity water. In the mining and metallurgical industries Recoflo ion exchange systems have been installed to treat a copper refinery bleed stream at Falconbridge's Kidd Creek plant and to treat a nickel and cobalt bearing ammonium sulfate effluent stream at another primary metal producer's facility. In the first application an APU® Recoflo system is used to separate the sulfuric acid at 200g/L from the dissolved copper and nickel sulfate salts at 80 g/L. The absorbed sulfuric acid is recovered from the resin by elution with water and is then returned to the refinery electrolyte circuit. In the second application a chelating ion exchange resin is used to remove nickel and cobalt at 0.01 - 3.0 g/L from process streams containing 120 - 240 g/L ammonium sulfate. This Recoflo system has been designed to reduce the nickel and cobalt levels to 0.001 - 0.002 g/L while recovering cobalt and nickel at concentrations up to 30 g/L and 15 g/L respectively. Case studies for both these metallurgical applications and other Recoflo processes are presented in this paper.

Jan 1, 1998

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

Heap leaching with thiosulfate is only used in one location for the treatment of a refractory preg-robbing gold ore initially pre-treated with bio-oxidation. The chemistry of thiosulfate leaching is complex. Further work is required to develop a better control of the system. A mild refractory gold ore containing pyrite and chalcopyrite was used in this study to investigate the use of thiosulfate as an alternative heap leaching technology. Preliminary bottle rolls tests indicated that similar gold extraction was obtained with cyanide and thiosulfate. In the column leach test, effects of thiosulfate, copper and ammonia concentrations, and their ratio on both gold extraction and reagent consumption, were assessed. The range of reagent concentration were: 0.1 - 1.0M (NH4)2S2O3, 0.03 - 0.10M CuSO4*5H2O, 1.0 - 6.0M NH4OH. The solid-liquid ratio was in the range of 0.83:1 to 5: 1. Best results showed that 72% of gold was extracted in 50 days with 0.3M (NH4)2S2O3, 0.05M CuSO4*5H2O and 6M NH4OH or a combination of 1.0M (NH4)2S2O3, 0.03M CuSO4*5H2O and 3M NH4OH. The reagent consumption at solid/liquid ratio of 3:1 was 37 - 48.6 kg/t (NH4)2S2O3 and 0 - 0.62 kg/t CuSO4*5H2O. The results of thiosulfate leaching were also compared with cyanide leaching.

Jan 1, 1999

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988