Search Documents

By Kuiting Wang, Jinshan Liu, Ninglei Sun, Aiguo Dong, Yeda Lu

"Eliminating the environmental threat caused by waste effluent containing magnesium sulfate derived from the process of nickel laterite sulfuric acid leaching and subsequent nickel precipitation is always a focus in the metallurgy field. A new flowsheet whose procedures include vaporization, crystallization, two stages precipitation of magnesium, causticizing treatment of filtrate and ammonia recycle was investigated. Both the details of the flowsheet and its application are described in this article. It is confirmed to be an effective and economical method to prevent the pollution by the waste effluent, simultaneity, a series of magnesium products recovered during the process own good economic returns.IntroductionSulfuric acid leaching is the conventional procedure of extraction valuable metals from ores in hydrometallurgy field. During the process of nickel laterite sulfuric acid leaching, several metals, including Ni, Co, Al Mn, Fe, Mg etc., migrate into the leachate in the form of soluble metal sulfate. After subsequent procedure of purification, precipitation of Ni and Co and neutralization, an enormous stream of waste effluent which contains a concentration of approx. 15-40g/L Mg is exhausted. Such solution containing magnesium sulfate is toxic, which causes diarrhea for both human and animals. On the other hand, large amount of sulfate acid was consumed during the process of leaching by the compound of Mg, which increases cost of a hydro nickel plant.In arid areas, the waste effluent mentioned above is treated via evaporate pond owning large acreage, which needs not only the appropriate meteorologic condition, but occupies much land. In coastal areas, it is directly discharged to the sea, which probably deteriorates ecological system of offshore strip. The most widespread method to treat with the waste effluent is neutralization by lime cream, the residues of which containing magnesium hydroxide and gypsum are transported to residues pool. Neutralization is a simple process, but it never recycles the Mg and sulfate anion into new application, meanwhile, the residues are potential threat to the environment."

Jan 1, 2012

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters, However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty, Ltd. in Australia.

Jan 1, 2003

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By Bowen Li, Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"Magnetic iron sulfide ore particles heat rapidly by microwave (MW) irradiation generating plasma during oxidation of surfaces. The high temperatures produced by the exothermic event decompose local portions of samples forming a differentiated flux of partially melted silicate (si-mt) with entrained metal-sulfide (sul-mt) droplets. The si-mt forms crystals of olivine (01) in Ca-rich pyroxene (Cpx) melt that resorbs a portion of iron sulfide (Po). The immiscible sul-mt droplets of (Fe,Ni,Cu)1-xS contain magnetic subsolidus Ni-pyrrhotite (Ni-Po) with Cr-bearing ferrospinel (Mag). Sub-micron sized flecks of Au are found on the surface of a sul-mt droplet with scanning electron microscope (SEM).IntroductionSulfide ore deposits supply the world's mineral resource in the production of non-ferrous metals. Particularly, Cu-Ni deposits are chemically enriched in metals from high sulfur saturation during magmatic formation that creates the proper geochemical environment for metals enrichment [1, 2]. The sulfur and oxygen fugacity control redox conditions of a differentiated silicate/sulfur magmatic melt with the concentration of iron playing a dominate role in the chemical partitioning of metals in sulfide liquid [3, 4]. The initial magnetic crystallization of (Fe,Ni)i-xS monosulfide solution (mss) from metal-sulfide liquid has an exclusive effect on the fractionation of mineral assemblages (zoning) [5].Phase equilibria of sulfide melt (sul-mt) components are related by a miscibility gap with mss forming Ni-rich pyrrhotite (Ni-Po) followed by the crystallization of (Fe,Cu)1-xS intermediate sulfide solution (iss) [6]. Precious metals form stable chacogenides and are retained in solution until the final liquid solidifies. The redistribution of metals now occurs by subsolidus cooling of mss and iss that exsolve low-temperature Fe-Cu-Ni bearing mineral assemblages [7]. The proper interpretation of ore genesis increases processing capabilities by isolating chemically enriched zones during extraction and should be used to aid in sustainable mine site development [8-11]."

Jan 1, 2013

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By Mostafa Maazouz, Jeff Blackwood, Mauricio Gordillo, Sang Hoon Lee, Micah Ledoux, Liang Zhang

To meet rising requirements for the low-damage ultra-fine process with the focused ion beam (FIB) in the materials science and semiconductor industry, the advanced ion column and corresponding advanced applications as a solution are developed and demonstrated. Novel high-speed high kV milling, low kV cleaning and imaging capabilities have enabled the creation of impeccable ultra-thin structures such as TEM samples and nanometer scale structures. Minimizing Ga+ induced sample damage is achieved through the optimized final cleaning at 500 eV ion landing energy with the new ion optics, which utilizes close control of the ion dose, beam incidence angle, spot size, pattern algorithm and imaging performance. Newly introduced process solutions achieve the improved process throughput. Initial demonstration is performed on the latest 14 and 10 nm scale FinFET device. Validation of the thinnest <0.8 nm thick ion damage layer on the <7 nm thick lamella structure was confirmed through TEM analysis.

Mar 1, 2017

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By Hideaki Tokuyarna

Recovery of metal such as V, Ni and Fe from oil fly ash is important for efficient use of natural resources and protection of environment. Leaching of metals from fly ash followed by ion exchange of leached metals has been examined to develop a process which can selectively recover V and Ni from the fly ash. Experiment of leaching with water, HCI, H2S04 and NaOH leads us to propose a two-step leaching process as an effective and mild operation. The first step is leaching with water for removal of Ni, Mg, A1 and Zn and the second step is leaching with acidic solution for the recovery of V. The metals V and Ni are then separated from other metals in each leached liquor by ion exchange. Advantage of this separation process is that acidic leachant can be reused, which contribute to save separation energy.

Jan 1, 2002

By Jun Li

Rate processes of silver cyanidation were studied with the objective of understanding the reaction mechanism. The research was divided into three sections: anodic dissolution of silver in cyanide solutions, cathodic reduction of oxygen on silver surfaces and the direct leaching of silver in oxygenated cyanide solutions. The charge transfer steps plus the diffusion of reactants from bulk solutions to the silver surface were identified as rate-limiting and the rates of both anodic and cathodic reactions can be calculated using the Butler-Volmer equation and Fick&apos;s first law. Based on mixed potential theory and the results of electrochemical studies, a comparison of the rate obtained from direct leaching with that predicted from the calculation is made. Calculated results agree well with the experimental data.

Jan 1, 1992

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Tomás Vargas

The catalytic role of Thiobacillus ferrooxidans in the dissolution of chalcopyrite was studied by leaching pure massive samples of this sulfide with a pure strain of Thiobacillus ferrooxidans (ATCC 19859). Monitoring of the bacterial activity showed that an important fraction of the total bacteria generated during leaching remained attached to the chalcopyrite surface. Bacteria grown in the system, which were the offspring of bacteria adhered to chalcopyrite, was well explained as the result of the utilization of ferrous ion and sulfur as energy sources. The potential for indirect and direct action was fully utilized by the existing bacteria and the leaching process was controlled by the kinetics of chalcopyrite dissolution.

Jan 1, 1990

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

By Robert S. Gärtner

The selective aluminum extraction by 3 different calixarenes (p-tert-butyl-calix[4]arene-tetra¬2-acetic-acid-ethyl-ester, p-tert-butyl-calix[4]arene-tetra-2-acetic-acid and p-tert-butyl-calix-[4]arene-di-2-acetic-acid-ethyl-ester) from an industrial pickling bath solution was studied. The pickling bath solution contained hydrofluoric and phosphoric acid as its main components. The aluminum removal was not successful and also no significant extraction of trace metals present was observed.

Jan 1, 1999

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000