Search Documents

By Natasa Mitevska

In the world, as well as in Republic of Serbia, conventional ore reserves are almost exhausted, so the problem of their shortage is more and more expressed. On the other side, there are many locations with significant reserves of polymetallic ores which present huge potential but cannot be classically processed. Each of these classes of materials has particular mineralogical characteristics which affect their processing. Because of that it is necessary to develop particular technology for each unconventional ore in order to extract valuable elements. The aim of investigation was to define technology for complex processing of the Blagojev Kamen sulfide concentrate by pyrometallurgical procedure in order to valorize valuable non-ferrous and precious metals present, and profit with absolute respect of environmental protection laws. The complex composition of the Blagojev Kamen sulfide concentrate with high content of non-ferrous (15.59% Pb, 9.05% Zn, 2.37% Cu) and precious (697 g/t Au and 744 g/t Ag) metals was the main factor for technological procedure and collector selection. Laboratory investigations are done in four series according to technological scheme: oxidizing roasting, charge preparation (flux addition and agglomeration), smelting under reducing conditions, lead bullion refining, Dore metal refining to final products. It is concluded that precious metals are concentrated in lead bullion (up to 97.95% of gold and 93.37% of silver), which has similar composition to lead bullion produced in lead metallurgy. In this case, simplified technology is used for lead bullion processing because of low content of arsenic, bismuth, etc.

Jan 1, 2006

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By Chuanhong Li, Zuohua Lin, Zhancheng Guo

"Catalytic mechanism of CeO2 in combustion of coals was investigated in this paper. Catalytic combustion of four kinds of coals with different metamorphic grades by CeO2 was examined, suggesting that catalytic function of CeO2 increases with increase of metamorphic grade of the coals. One important reason for CeO2 promoting combustion of the coals is that pyrolysis of anthracite is advanced by CeO2, which not only raises the pyrolysis rate and pyrolysis conversion ratio, but increases contents of light components in pyrolysis gas; and both pore space and specific surface area of the pyrolysis char are enlarged by CeO2, which is another reason. In order to realize in situ catalysis for reducing catalyst consumption, it is crucial to increase catalyst particle number and enhance the bonding force between catalyst and coal. In addition, remarkable energy saving effect was observed when a nanometer calcium-based rare earth catalyst obtained by hydro-thermal synthesis was applied to catalytic combustion of coal injection into blast furnace.Introduction Coal combustion is acknowledged as one of the most important coal applications. Since addition of catalysts could reduce the ignition temperature of pulverized coal and accelerate the coal combustion, catalytic combustion is generally accepted as an effective measure to realize fast combustion of coal. Furthermore, different catalysts added may produce different effects on ignition temperature of coal. It is reported activity of catalysts with the same cation follows this order: OH->CO3 2->Cl->SO4 2-; while that of the catalysts which have the same anion follows: Cs+>Rb+>K+>Na+>Ba2+>Li+>Sr2+>Ca2+>Mg2+>Be2+ [1-4] .Due to the special physical and chemical structure, CeO2 plays an important role in the catalysis field. Many literatures point out that CeO2 not only has great catalytic effect on energy conversion, succeeded in catalyzing combustion of gaseous fuels such as CH4, CO, etc. but also can catalyze combustion of some liquid and solid fuels such as JP-10, black carbon, carbon deposit in the automobile exhausts and so on [5-9].Pyrolysis, the first step of combustion, directly influences ignition temperature and combustion rate of coals. So a great variety of catalysts were applied to catalyze pyrolysis of coals. And plenty of studies suggest that the alkali and alkaline-earth metal compounds inherent in the coals show apparent catalytic effect on coal pyrolysis. Meanwhile, addition of alkali and alkaline-earth metals into coal combustion process also indicates obvious catalysis effect, accelerating coal pyrolysis, improving pyrolysis conversion ratio, increasing contents of pyrolysis gases and changing composition of the pyrolysis gases [10-15].Although alkali and alkaline-earth metal compounds have good catalysis effect on coal combustion, their application in the catalysis field was limited because of their erosive attack to the combustion equipments. In contrast, CeO2, as a substitution of the traditional coal catalysts, presents widely potential application due to its good catalysis ability, non-corrosive and nontoxic. However, investigation on CeO2 catalyzing coal combustion is rarely reported. In this work, catalytic mechanism of CeO2 in coal combustion was studied, in an attempt to provide theoretical foundation for developing new catalysis technologies."

Jan 1, 2009

By Joseph J. Poveromo

Technical progress in ironmaking will be discussed in three sectors: blast furnace ironmaking, direct reduction and alternative ironmaking to feed electric arc furnaces and ironmaking for waste oxide processing. The contributions of iron ore producer, Quebec Cartier Mining, in each sector will be outlined.

Jan 1, 2006

By S. P. Jupp

A 2-D coupled thermo-mechanical model was developed to simulate hot tandem rolling of AA5056 aluminum alloy using the commercial finite element software package, ABAQUS The model was used to predict the temperature, strain rate and strain distribution in the strip at any position in the roll bite and was verified through comparisons with literature results in terms of both temperature and strain predictions at the roll bite exit. A sensitivity analysis indicated that model predictions of temperature and strain at the roll bite exit were sensitive to the friction coefficient and moderately sensitive to the heat transfer coefficient for the conditions studied. Microstructure equations taken from the literature were used to make predictions at various positions in the strip. The temperature, strain rate and strain vary dramatically through the thickness of the strip in the roll bite. The sensitivity of the microstructure predictions to these parameters was assessed and it was found that using average values of temperature and strain rate in the roll bite versus exit values significantly influenced the resulting microstructure predictions.

Jan 1, 2001

By V. Gel

An analysis of the operation of rotary tilting furnaces has indicated that they ensure better recoveries of metal when smelting lump scrap from aluminum slags, brass and bronze. On the other hand, processing of slags (concentrates obtained by mechanical upgrading) in pear-shaped furnaces results in much lower performance values as might be expected. At the Novgorod metallurgical plant a process for blister copper production in a rotary TROF converter (Outokumpu, Finland) has been introduced on a commercial basis. Smelting of brass and bronze scrap to produce blister copper is carried out using the technology developed in Russia and differing from the Outokumpu technology by the types of flux used and the blowing conditions in fuel burners and for melt oxidation, as well as by the design of gas removal system, the design of nozzles for melt blowing and the use of carbonaceous reductant (coal) for magnetite reduction in slags. Industrial-scale testing has demonstrated that by means of special techniques the 30-tonne converter productivity can be increased by 30% to 40% as compared with its rated productivity.

Jan 1, 2006

By Gerardo R. Alvear

The ability to efficiently remove impurities contained in concentrates is a key point to consider when selecting copper smelting technology for new plants or modernisation projects. Volatilisation of impurities such As and Sb should occur as early as possible in the process, and preferably in the smelting furnace, so that they do not impact on downstream unit operations. The ISASMELTTM process has been demonstrated to remove impurities efficiently, through high levels of volatilisation. This behaviour is promoted by attributes of the process such as the strong bath agitation, and the flexible nature of the process design, allowing the operator to choose the optimal matte grade for impurity partitioning, and the positive effect of the moisture content in the feed. This paper presents the distribution of minor elements in the copper ISASMELTTM furnace. Distribution impurities of As, Sb, Pb, Zn and Co observed in the ISASMELTTM furnace at Mount Isa Smelter are reported. Then, based on plant results and thermodynamic considerations, the potential application of ISASMELTTM technology for processing complex concentrates is discussed.

Jan 1, 2006

By P. Stantke

In recent years the CollaMat process has been used successfully worldwide in a number of copper electrorefining tankhouses as an instrument for measuring the glue concentration and optimizing cathode quality. Owing to its measuring principles the CollaMat can be used not just for measuring the concentration of active glue but also the activity of other substances, which have an impact similar to glue on the copper deposition. In SX-EW plants guar is frequently used instead of glue as a levelling additive. In our laboratory the effect (activity) and the decomposition rate of guar in copper electrolyte was examined. As expected, the results show that guar has an effect similar to glue on the copper deposition. However, at the same temperature, a greater quantity of guar is required to achieve the same results. As with glue, the decomposition rate (due to hydrolysis) of guar is strongly dependent on the temperature. Therefore, in practice, its on-line monitoring is necessary to guarantee the same guar activity at any time.

Jan 1, 1999

By R. Togashi, S. Kuramochi, T. Yamada

In 1972, the Akita Zinc Co., Ltd. commenced operations with an annual capacity of 86,000 tonnes of electrolytic zinc, and it has operated with an annual capacity of 156,000 t-Zn since 1974. The business surroundings for non-ferrous metals production have become more severe with the high Yen rate for the dollar and low domestic demand in the last few years. Consequently, the company tried to survive with some improvements and succeeded to reduce operating costs and to improve profitability as follows: 1) expansion of its production capacity to. 196,000 t-Zn annually, 2) saving man-power by the introduction of fully-automated machines for cathode handling in the cellhouse, 3) improvement of the hematite process by means of the recovery of rare-metals. These improvements made Akita Zinc a competitive refinery in the modern world. We have been trying to improve the operations more and more. One of the challenges is to purify the iron oxide made in the hematite process by applying an As removal process, which is coming into operation in the near future.

Jan 1, 2000

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By G. Achurra

The products of the smelting of copper concentrates in an El Teniente Converter (CT) are a high grade matte, analyzing 74-76% Cu; and a highly oxidized slag, typically containing 15-20% Fe3O4 and 4-10% Cu. The El Teniente Division of CODELCO¬CHILE has developed a slag reduction-cleaning process, that is practised in a tilting, horizontal furnace, to recover copper from these slags. The El Teniente slag cleaning process has been successfully implemented at the El Teniente Caletones smelter and various other smelters in Chile: Today, eight such slag cleaning furnaces, each with a capacity of 800-1000 tonnes/day, are in operation in Chile. This paper discusses basic laboratory research and industrial tests that led to substantial reductions in the slag cleaning cycle time and the specific consumption of fuel and reductants. Simultaneously, the slag cleaning off-gas quality was improved. Based on the experimental results, recommendations were made to improve the practice of the El Teniente slag cleaning process. The recommended modifications have been fully implemented at the Caletones smelter.

Jan 1, 1999

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

The viscous behavior of molten slags has played an essential role in determining the performance and productivity of the ironmaking process. In this paper, the viscosity and free running temperature in CaO-SiO2-Al2O3-9 mass% MgO-TiO2 slag has been measured at different content of Al2O3 and Al2O3/SiO2 ratio. In addition, the slags viscous activation energy has also been calculated. The results show that the TiO2 as a basic oxide content from 1 to 5 mass% can reduce the viscosity and free running temperature, and moderate content of TiO2 in high alumina blast furnace slag remains effective for reducing viscous activation energy and free running temperature.

Mar 1, 2018

By Lifeng Zhang

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both C02 and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na2C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO2 and argon. However, less residue is formed when heated in CO2.

Jan 1, 2008

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013