Search Documents

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

The wettability behavior of graphite with silicon is a key factor for its application as a crucible in silicon making industry. A previous study was carried out to determine the correlation between the physico-chemical behaviors of different types of graphite and the final contact angle for the graphite/silicon system. In this study, experimental vacuum annealing treatment by varying the exposure time at high temperature of 1000 °C processed by X-ray photoelectron spectroscopy and SEM analyses enabled to found a correlation between the oxygen content in the graphite and the final contact angle for the graphite/silicon system. Finally, the experimental results with and without vacuum annealing treatment have shown that a deep infiltration of silicon inside the graphite occurs in case of high level of oxygen content inside the graphite’s pores.

Mar 1, 2017

By Peiye Yan, Huiqing Tang

To reduce coke consumption in blast furnace ironmaking, this study proposed a new method of applying iron-coke briquette prepared using hematite powder and pulverized coal to protect coke in BF iron making. Results showed that, with a ratio of hematite to coal of 2.0, the iron-coke briquette could obtain a satisfying compressive strength of more than 1500 N both before gasification and after being gasified by CO2 for 1 h. The activation energy of the iron-coke briquette was 93–135 kJ/mol, which is lower than the coke and therefore could protect the coke in BF. The agglomeration and stratification of iron particles occur in the course of iron-coke briquette gasi fication and is bene ficial to the improvement of the iron-coke briquette strength.

Mar 1, 2018

By Patricia Negrini Siqueira Poveda, Leonardo G. A. Silva

Thermoplastic materials are sensitive to ultraviolet radiation (UV), which can cause structural changes, causing variation in mechanical properties and appearance. UV range between 250 and 400 nm is considered the most aggressive to polymers, and prolonged exposure to it results in breakage and/or crosslinking chains. Light stabilizer additives, blockers or absorbers are added to the polymers for protection in order to extend the life of the final product. The choice of the adequate light stabilizer additive system depends on factors such as resin final application, thickness, geographic location of exposure, presence of fillers in the composition, contact with chemicals, among others. This study evaluates different additive systems: conventional organic, inorganic nanotechnologyc base and the synergy between them when applied to polyethylene considering carbonyl index and UV/VIS results after aging by QUV chamber.

Mar 1, 2017

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By M. G. King

In 1982, Asarco operated six smelters and refineries producing primary copper, lead, zinc, silver and gold. At that time Asarco was still reliant on its custom smelting and refining roots and mined only 25% of its smelting and refining capacity for copper and 10% of its lead smelting and refining capacity. By 1992, Asarco had been reshaped to become largely an integrated primary metal producer operating four smelters and three refineries. Zinc is no longer refined and the mining capacity has been increased to meet 100% of copper smelting and 50% of lead smelting needs. Only one custom smelter is in operation. This paper describes the metallurgical changes and challenges which have occurred in this restructuring of Asarco's operations while maintaining Asarco's position as one of the largest non-ferrous metals producers in the world.

Jan 1, 1993

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By Chen Tian, Tingfeng Wu, Qinghai Pang, Junhong Zhang, Zhijun He

Microwave technology as new aided tool has been applied on waste water treatment and metallurgical fields. This paper explores the affected factors such as microwave power, microwave irradiation time, polyaluminium chloride (PAC) amount and addition of phosphoric acid on treatment of Blast Furnace gas washing water by utilization of coagulation associated with microwave. Through the orthogonal experiment, the optimum experimental parameters were obtained in the course of treatment of 300 ml Blast Furnace gas washing wastewater: 396 W microwave power, 2 min of microwave irradiation time, 0.12 ml Added PAC and 0.8 ml added phosphoric acid. It indicates the affected factors in descending order on removal of SS in BF gas’s washing water: Added PAC level, added phosphoric acid level, time of microwave irradiation, and microwave power while those parameters that can affect suspended solids(SS)’s hardness reduction in descending order are added phosphoric acid level, added PAC level, time of microwave irradiation, and microwave power. Also, it demonstrates those parameters that can affect washing water’s turbidity in descending order: Added PAC level, time of microwave irradiation, added phosphoric acid level, and microwave power. The results showed that PAC coagulation associated with microwave on treatment of Blast Furnace gas washing wastewater has several benefits: short treatment time, strong sedimentation velocity and other excellent characteristics, it can effectively remove suspended solids in wastewater, the SS hardness and turbidity can be reduced.

Mar 1, 2017

By Richard M. RusselI, Jerry Sweeney

"The disposal of Aluminum slag wastes continues to challenge an otherwise environmentally beneficial and highly desirable industry - Aluminum Recycling. Slag wastes contain soluble salts that can be reused in aluminum smelting. Reclaiming salt is a logical first step in eliminating slag waste.Reclaiming salt flux has been conducted on a limited basis in the United States for reasons of economy. Practical methods and rising landfill tipping fees will increase the number of plants which opt to recover salts from slag wastes.The authors share their experiences in the design, operation and startup of a commercial scale flux reclamation plant operated by Tennessee Aluminum Processors at Mt. Pleasant Tennessee. This paper identifies three elements that allow practical operations:• Minimizing Evaporator Heat Duty• Simplifying Evaporator Operations• Potassium Chloride Fortification of the Recycled Salt"

Jan 1, 2000

By Sharon K. Young

What might an ideal leach-to-cathode/product system look like in the next century? The paper looks at the synergies of the 60's and 70's that led to the highly effective copper leach SX-EW system of the 90's. Standing in the year 2020 focuses on what breakthrough technologies might make possible a next generation leach/extraction/metal recovery system. Many of the pieces of such a technology have been developed, even piloted: in situ leaching, enhanced bioleaching, heap leaching of fine particles, resin in pulp, ion exchange, alternate anode reaction electrowinning, novel anode coatings. With nearly non-existent research on the part of individual large companies, the greatest challenge may not be inventing the technologies but rather inventing an industry "will to create."

Jan 1, 1999

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By Jr. Santafé, Lucas L. da Costa, Felipe P. D. Lopes, Sergio N. Monteiro

"Residual vegetable fibers as leftovers from crops, industrial activities and consumable items are realistic options to be incorporated into low cost polymeric composites with the aim of replacing other commonly used materials. The present work assesses the technical properties of epoxy composites reinforced with residual fibers from the coconut fruit, also known as coir fibers. Based on these properties, an evaluation was carried out on these coir fiber/epoxy matrix composites to be used as building panels and furniture in comparison with conventional materials.IntroductionThe utilization of waste from industrial activities is presently recognized as important way in preventing environmental pollution as well as developing new products. This utilization would also generate employment and contribute to environmental improvement in global scale. Among such wastes, those from lignocellulosic materials represent a considerable potential for practical application. In fact, about 2.5 billion tons of these materials are currently available [1], and their fiber content is an important option for composites fabrication. Actually, lignocellulosic fibers are now replacing synthetic fibers as reinforcement in resin matrix composites owing to specific advantages such as low cost, biodegradability and renewable characteristics [2,3]. Moreover, as abundant waste, some of these lingocellulosic fibers could help reducing the use of traditional materials like wood and plastics in many industrials applications. This would prevent further stress on the environment caused by depletion of dwindling resources associated with forests and petroleum."

Jan 1, 2008

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By Alex Moyano

The Peirce-Smith converters are traditionally carrying out the converting process of a copper matte in the smelters of Codelco-Chile. However, its production increment is very limited due to the investment magnitude associated to the fulfillment of the environmental regulation. The objective of this paper is to present the Codelco continuous converting process technological advance when converting mattes and/or white metal into blister copper in a Teniente converter unit as an alternative to increment the corporative anode copper production. In 1994, Codelco-Chile started evaluating its ?home made technology? as an alternative to the traditional batch-type converting process. By the year 2001, the Caletones smelter converted liquid white metal to blister copper in a rearranged PS converter continuously. Then, during the 2001-2003 period, several pilot and industrial scale tests were done in a Teniente converter unit at Codelco Norte smelter, evaluating the continuous converting process, i.e., processing liquid mattes (62-68% Cu) to blister copper, demonstrating its technical feasibility with: (i) both constant production of gas flow and SO2 concentration, (ii) production of liquid slag, and (iii) production of a clean blister copper, suitable for the refining process. The promising results have led Codelco-Chile to plan for the 2006 period, a next advanced stage for the continuous converting process evaluation by carrying out a new campaign of tests in a Teniente converter unit at the Codelco Norte smelter.

Jan 1, 2006

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By E. Almendras de Siegel

Pyrometallurgical processes have the thermodynamic capability of treating complex and dirty ores and concentrates to produce high purity metals and inert slags. Modem pyrometallurgical processes are environmentally sound and competitive with other processes. However, there is still a need for sensors and other practical tools that permit a rapid evaluation of the performance of these processes. In order to contribute to satisfying this fundamental requirement, the authors developed the IDENT.LA software that permits the automatic mineralogical analyses of inorganic materials, including the final and intermediate products of pyrometallurgical processes. The technique allows determining the grain size distribution of mineralized inclusions, the surface relations between metallic phases, and conducting modal analyses of the essential phases that are present in the samples. Three basic automatic operations are performed: creating a representative image of the sample; identifying the metallic and non-metallic phases; and measuring the features of the resulting image. The results are used to evaluate the performance of pyrometallurgical and other processes. In this paper, the authors discuss the application of the technique to a sample of slag from a slag cleaning process that uses a carbonaceous reductant. In this case, process performance impacts not only on the efficient reduction of the slag magnetite and on copper recovery but also on the quality of the process off-gas. The mineralogical analysis of the slag is a valuable tool in assessing process performance and in recommending changes of operating conditions.

Jan 1, 1999

By P. C. Guillaume

Global plant modernizations or expansions cannot be considered in the same light as any other industrial investment project. Relationships between the partners, relationships and communications with the client, structure and organisation of the teamwork, schedule of the work, and a lot of other tasks and missions devoted to external contractors have to be defined considering one fundamental input: an operating plant. For an engineering company expert in processing, like UM Engineering, such a context requires a specific approach as well as specific procedures able to efficiently challenge the generated constraints. First of all, even if a detailed audit had been conducted at the beginning of the conceptual engineering phase, new elements will be discovered during the preparation and realization of the project, and must be continuously integrated. Consequently, a close proximity to the site is necessary. This is one reason why UM Engineering, most often, works in partnership with a local engineering company. The second important point for the client is that the operation must not be interrupted during the realization. In order to make that possible, UM Engineering has defined a specific project structure and organisation, integrating on a permanent basis the operators (the "users") in the project teams. This paper presents the way UM Engineering copes with this type of "multi-constraints" context with reference to the recent copper cellhouse modernization under realization for the CCR Refinery of Noranda Inc. in Canada.

Jan 1, 1999