Search Documents

By A. R. Laplante

Recent developments in gold metallurgy are used to illustrate how the interface between gravity recovery and hydrometallurgy has evolved in recent years. Of particular interest is the use of gravity recovery to produce high-grade concentrates that can be subjected to intensive cyanidation. It is expected that a growing proportion of gold production, possibly close to 50% in certain countries, will follow this route. Other examples of the interaction between gravity recovery and cyanidation are also provided. Implications for new and renewed research directions are discussed.

Jan 1, 2003

By Maria S. Gudjonsdottir, Miao Yu, Gudrun Saevarsdottir, Pall Valdimarsson

Around half of the energy consumed in aluminum production is lost as waste heat. Approximately 30–45% of the total waste heat is carried away by the exhaust gas from the smelter and is the most easily accessible waste heat stream. Alcoa Fjarðaál in east Iceland produces 350 000 tons annually, emitting the 110 °C exhaust gas with 88.1 MW of heat, which contains 13.39 MW exergy. In this study, three scenarios, including organic Rankine cycle (ORC) system, heat supply system and combined heat and power (CHP) system, were proposed to recover waste heat from the exhaust gas. The electric power generation potential is estimated by ORC models. The maximum power output was found to be 2.57 MW for an evaporation temperature of 61.22 °C and R-123 as working fluid. 42.34 MW can be produced by the heat supply system with the same temperature drop of the exhaust gas in the ORC system. The heat requirement for local district heating can be fulfilled by the heat supply system, and there is a potential opportunity for agriculture, snow melting and other industrial applications. The CHP system is more comprehensive. 1.156 MW power and 23.55 MW heating capacity can be produced by CHP system. The highest energy efficiency is achieved by the heat supply system and the maximum power output can be obtained with the ORC system. The efficiency of energy utilization in aluminum production can be effectively improved by waste heat recovery as studied in this paper.

Mar 1, 2018

By Chikabumi Yamauchi, Masami Tashiro, Toshiharu Fujisawa, Hiroyuki Snano

"Rare earth metals usually contain large amount of oxygen because of their reactiveness, and therefore oxygen removal is one of the major problems on the purification of rare earth metals. In the present research work, halide flux treatment at high temperature under inert gas atmosphere was applied to the oxygen removal from neodymium. NdF3 was used as a halide flux. Deoxidation reaction and its mechanism were discussed based on the experimental results. Halide flux treatment is very effective for oxygen removal from rare earth metals.IntroductionSolid Sate Electrotransport (SSE) process has been successfully applied for the elimination of interstitial gaseous impurities from chemically active metals[l]-[5]. However, to achieve a higher effectiveness of the SSE process, it is required a very low initial impurity content in the metal. In case of rare earth metals, it is known that they usually contain large amount of oxygen that should be lowered as much as possible before applying the SSE process. In addition, if effective oxygen removal is achieved by simple process, it is significant also from the industrial viewpoint. In the present work, the application of a halide flux treatment is investigated to remove oxygen from neodymium by using NdF3 as a flux. At first, deoxidation reaction and its mechanism were discussed based on the phase diagram of the Nd-NdF3-Ndp3 quasi-ternary system. Based on the results, oxygen content in deoxidized neodymium was calculated theoretically and it was verified by deoxidation experiments."

Jan 1, 1998

By Eiji Iwamura

"Two types of diamond-like carbon (DLC) films with different microstructures were prepared by unbalanced magnetron sputtering, and the tribological properties of the nanoscaled DLC multilayer coatings consisting of alternating layers of graphitelike and amorphous-like microstructures were examined. The DLC microstructure was characterized by certain features of graphite-like clusters, in that some of them had onion-like structures. The films filled with the clusters were obtained in a condition with an incidence of high influx of energetic electrons, and the other films without apparent cluster structures were formed in a condition with ion bombardment controlled by negative bias voltage applied to substrates. Stacking each film layer-by-layer, the nanoscaled multilayered coatings showed superior tribological properties to individual single-layered films due to the combination of properties induced by the difference of microstructures.IntroductionIn various tribologiql applications, it is necessary for diamond like carbon (DLC) coatings to have adequate adhesion, significant hardness and a concomitant low friction coefficient. A number of deposition techniques and coating structures have been proposed to achieve suitable DLC properties [1-3]. However it is still difficult to obtain a satisfactory level of combination of the properties particularly desirable for engineering applications.In this study, the features of unbalanced magnetron sputtering were demonstrated with the effect of ion and electron bombardment. Two types of microstructures , namely amorphous-like and graphite-like, were prepared by changing the condition of the charged particles bombardment during deposition. Using the difference of properties induced by the microstructures, nanoscaled DLC multilayered structures were examined in an attempt to improve tribological properties."

Jan 1, 2000

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By J. H. de. Visser

The transfer of molten metal in smelting or refining operations is typically performed in open trough-type launders that are constructed of either water-cooled copper troughs or refractory lined steel jackets. This transfer can be either continuous or batch. Batch operations transfer metal through an open launder. The uncovered launder has many operational and environmental drawbacks. In order to improve workplace hygiene, designs have evolved toward ventilated launder covers that .are connected to secondary exhaust systems that use negative pressure under the cover removing fume and hot gases to secondary fume control devices. In smelting operations, a variety of covers have been employed which insulate the launder and contain the fumes and also provide additional heat along the length of the launder through a series of premix or inspiration-type burners that add combustion products to the normal fume load in the launder. Cover designs have proven to be inadequate in that hinged unventilated covers hinder convenient access while heated ventilated covers are costly to maintain. Covers that employ refractory bricks and overhead enclosure-type exhaust hoods have been somewhat successful, but restrict operator movement and require large volumes of exhaust air. An example is given of a cover and off-gas system for launders that is designed to provide superior insulation and heating capabilities, as well: as better control of the fume gases-and ease of maintenance. The cover system must maintain the balance between maintaining launder heat and fume removal. The construction of the covers must be able to withstand high internal temperatures and maintain its structural properties.

Jan 1, 1999

By David Langberg

Recovery of dissolved copper from discard slags is a critical consideration affecting the economics of copper smelting. Slag cleaning is frequently carried out in electric furnaces, however reduction by injection of natural gas in a holding furnace may offer a lower cost alternative in some circumstances. As the residence time of the injected gas is short, the factors controlling the rate of reduction need to be clarified in order to optimise the design of the slag cleaning furnace. A series of medium scale (200 kg) reduction tests to investigate the rate of reduction of copper-containing slags by injection of natural gas-nitrogen mixtures between 1150-1250C was carried out by CSIRO Minerals. The composition of the gas in the top-space of the reactor was found to be significantly more reducing than the slag, indicating that thermodynamic equilibrium was not established between the slag and the gas in the bubble plume. An apparent first order rate law was observed between the rate of oxygen elimination from the bath and the magnetite concentration of the bath. The dissolved copper concentration was closely correlated with the oxygen potential of the slag, suggesting a partial equilibrium between the dissolved components of the slag. The utilisation efficiency of the natural gas decreased as the natural gas flow rate was increased. The results of the tests tend to indicate that the rate is controlled by a mixed reaction kinetics/ mass transport mechanism. The work was supported by Xstrata Copper ? Mt Isa Mines.

Jan 1, 2006

By Brad Wahlquist

An ex-situ biological treatment system was implemented at a gold mine site in South Dakota. The system removes selenium and nitrate from a mixture of groundwater and surface water runoff at ambient water temperatures. The Applied Biosciences? system replaced a denitrification system that did not perform consistently, did not treat for selenium and required heating of the influent water. Installation was completed in phases starting with the selenium circuit being brought into operation in February, 2002 and the nitrate circuit in March, 2002. System design can accommodate average flows of 380 L/min (100 gallons/minute) and a maximum flow of 1,136 L/min (300 gallons/min). Four cells were designed to remove nitrate from approximately 30 mg/L to below 10 mg/L and two cells were designed to remove selenium from 0.01 mg/L and higher, to below 0.005 mg/L. No pretreatment is required to operate the system at ambient temperatures, which can fall as low as -12C in the winter, and treat water at temperatures ranging between 8C to 16C. Nutrient requirements are met using a sugar based nutrient mixture that includes a balanced C:N:P:S ratio, trace elements and vitamins. Since start up, the system has consistently been in compliance for nitrate and selenium, treating water to below detection limits for both contaminants. This paper discusses laboratory biotreatability testing of a system designed to remove selenium, arsenic, and nitrate and full-scale implementation and optimization of a system to remove nitrate and selenium.

Jan 1, 2003

By Thomas K. Chow

For the well-being of all living creatures and in response to green-environment policy from governments around the global, it is essential to reduce SO2 emissions from mining / smelters as well as other industrial facilities around the globe. However, often times, these SO2 containing flue gases and smelter flash gases also include oxygen and SO3, which complicate the SO2 removal process and technology. There are many novel technologies recently developed for removing SO2 from such gases. Most of these, however, have not yet commercially demonstrated that they are technically viable and economically feasible. Many of these novel processes also generate undesired byproducts, which themselves then need to be disposed of in a safe and cost effective manner. Fluor has developed the Fluor SOx Cleanup Process with a wide variety of process configurations to customize removal of the undesired flue gas constituents in a cost-effective manner. The process removes practically all SO2 in the form of salable elemental sulfur and also reduces CO emissions. Successful operation of major components of the Fluor SOx removal technologies has been demonstrated in many commercially operating units. Besides their technical viability and economic feasibility, Fluor SOx removal technologies do not generate any undesired byproducts or encounter SO2 associated corrosion issues. Moreover, these technologies produce high-purity, saleable elemental sulfur. This paper discusses the merits of the Fluor SOx removal technologies, their technical and cost advantages, their simplicity in design and operation, and their readiness for implementation.

Jan 1, 2006

By T. T. Chen, J. E. Dutrizac

Noranda Inc., CEZinc presently employs a cement-stabilization (jarofix) process to stabilize its jarosite residues for direct disposal. In this process, Portland cement partly decomposes Na-jarosite to form Ca6Fe2(SC>4)3(OH)i2.nH20, ferric hydroxide and sodium sulphate which further reacts to form gypsum; approximately one-third of the Na-jarosite reacts in the current commercial product. The cured jarofix products also contain minor amounts of various Ca-Al-Fe silicate-sulphate-hydrate phases and traces of calcite. Together with gypsum and a Ca-Fe sulphate phase, these species bond the various particles together, imparting mechanical strength and reducing the permeability. Water-soluble Zn and Mg are stabilized in the Ca-Al-Fe silicate-sulphate-hydrate phases. The freshly cured products usually contain small amounts of moisture and traces of residual Portland cement, which provides additional alkalinity for the neutralization of any residual acid species. Jarofix products stored for more than six years in the laboratory, after curing, are usually dry and exhibit the same micro-textures as those of the freshly cured products. However, the stored products are depleted in the Ca6Fe2(S04)3(OH)i2.nH20 and Portland cement phases, and are enriched in gypsum and calcite which reflects the highly alkaline environment of the jarofix products. The aged products also have increased amounts of the Ca-Al-Fe silicate-sulphate-hydrate phases which have elevated Zn and Mg contents. This implies a further immobilization of residual water-soluble Zn and Mg during stora

Jan 1, 2000

By E. R. Vance, D. R. M. Brew

"Historically, Ordinary Portland cement has been the preferred medium to immobilise arsenic. However, arsenic in cement gives rise to calcium-arsenic phases and their known decomposition to calcium carbonate and arsenic trioxide via atmospheric carbonation raises serious questions about the long-term suitability of cement for arsenic immobilisation. Alternative matrices such as low-temperature ceramics (LTCs) potentially offer superior resistance towards carbonation owing to the absence of calcium. Consequently, the potential for arsenic immobilisation using LTCs has been investigated. Both AsIII and AsV have been incorporated and samples assessed according to a standard leaching protocol. AsIII persists in the porewater of alkali-bonded LTCs as sodium arsenite rendering them unsuitable for immobilisation. Thermal treatment of these LTCs to consolidate the microstructure and reduce open porosity resulted in sodium-rich cryptocrystalline matrices that leached arsenic and sodium readily. The omission of sodium in acid-bonded LTC formulations resulted in leach data that were close to the target value of 5 µg/ml in Toxicity Characterisation Leaching Protocol tests.IntroductionArsenic is a carcinogenic substance and its adverse effects of on humans, flora and fauna have been well documented [1-5]. As a consequence, many papers have been written on the prospective handling of arsenic-bearing waste. These can largely be divided into: (a) cleanup of arsenic-contaminated water using bacteria, precipitation, and/or UV irradiation to generate arsenic-rich sludges for subsequent immobilisation; (b) cleanup of arsenic-contaminated soil via chemical extraction for immobilisation of the As concentrate; and (c) immobilisation of industrial waste contaminated with As."

Jan 1, 2008

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By Hu Meilong, Liu Lu, Bai Chenguang

Extracting perovskite from high titanium-bearing blast furnace (BF) slag is a green and potential method to recover the second titanium resource. The non-isothermal crystallization process of perovskite in synthesized high titanium-bearing slag was studied in situ by confocal scanning laser microscope (CSLM) with cooling rate of 20 K/min. The results showed that perovskite was the primary phase formed during cooling process in the titanium-bearing synthesized slag (TiO2=23%). Perovskite started to precipitate at 1719 K and finally presented an orthogonal straight lines morphology.

Jan 1, 2014

By M. GONZALES-FERNANDES M

Natural rubber/organophilic clay nanocomposites were prepared and characterized. A brown bentonite from Paraiba’s State, Brazil was modified with a sodium salt and treated with quaternary ammonium salt hexadecyltrimethyl ammonium chloride. The clay in its natural state, after cation exchange with sodium and after organophilization was characterized by XRD, IR, SEM, thermal analysis. Nanocomposite samples were prepared containing 10 resin percent of organophilic clay. The vulcanized samples were analyzed by XRD, SEM. The nanocomposites obtained showed improvement in their mechanical properties in comparison with samples without clay.

Jan 1, 2015

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70' s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol'lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989