Search Documents

By Nourreddine Menad

Plastic materials have been associated with electric and electronic applications since the early days of the electrical industry. Plastics can amount to 30 percents of the scrap mass. Generally, they are treated with flame retardants such as halogenated ones and they can result in different toxic chemical compounds. These plastics can be used as combustibles in the recovery of copper and precious metals. However, during their combustion, halogenated flame retardants can produce dibenzo-p-dioxins and dibenzo-furans. The estimated thermodynamic data of several organic compounds resulting from combustion of electric and electronic scrap, have been used in conjunction with the program HSC to calculate the conditions for dioxin and furan formation. The results show that the formation of the dioxins is dependent on the quantities of carbon, hydrogen, chlorine and oxygen reacting in a given system, as well as on parameters such as temperature and pressure.

Jan 1, 1998

Microstructural investigation has shown that grain splitting or deformation banding ( DB ) develops progressively with increasing strains during cold rolling. Of particular significance to simulating texture development in cold rolled BCC polycrystals is the operation of higher order slip systems other than 110 and, the occurrence of DB in the rolling plane since the latter allows a new relaxation of the shears. Deformation banding ( DB ) model includes grain subdivision in the rolling plane and applies the Relaxed Constraints ( RC ) mechanism for the other shears. An energy criterion for deciding whether deformation banding occurs or not has been postulated, referred to as Deformation Banding Criterion ( DBC ). This paper reports the results of the investigations into the effects of different slip systems, i.e., those based on 110, 112 and 123 slip planes and their combinations using RC, DB and DBC models, in developing simulated BCC rolling textures.

Jan 1, 1999

By H. Walqui

Southern Peru Copper Corporation (SPCC) are currently modernizing the Ilo copper smelter. A single ISASMELT furnace will start smelting 1,200,000 tonnes per year of concentrate during the second half of 2006. The existing Peirce Smith converters are being upgraded for converting the matte to blister copper and a new acid plant and oxygen plant are being installed. Two new anode furnaces and a twin anode casting wheel have been installed in 2005 and commissioned in January 2006. The modernization project will ensure the smelter satisfies new environmental regulations due to come into force in January 2007. This paper summarises the background to the modernization project, describes the main design features of the new copper smelter and summarises progress on the smelter construction as of early 2006. This paper describes the genesis of the Ilo Smelter Modernization Project and describes in details the scope and current status of the project.

Jan 1, 2006

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By B. Bichel

For the last 70 years, molten blister copper has been transferred by rail in hot metal cars from the Copper Cliff Smelter to the Copper Cliff Copper Refinery (ex Ontario Refining Company) where it was processed in two (2) reverberatory anode furnaces by poling with logs, cast on four (4) wheels, and then electrorefined. This practice was modernized in 2001 with the installation of two (2) rotary anode furnaces at the. Copper Cliff Smelter which employ steam and. natural gas for reducing and which provide a significant reduction in emissions. A new casting shop with a single anode casting wheel is used to cast regular and stripper constant weight anodes which are transported by truck to the Copper Cliff Copper Refinery for anode preparation and electrorefining. This paper provides an overview of the copper circuit at the Copper Cliff Smelter and a description of the CDN$31 million capital project.

Jan 1, 2002

By Carlos Maurício F. Vieira, Giulio R. Altoé, Maria Carolina A. Teles, Sergio N. Monteiro, Maycon A. Gomes, Frederico M. Margem, Gabriel O. Glória

Due to growing concern about the ambient impacts, the society is demanding for materials that are environmentally friendly. The lignocellulosic fibers, like PALF fibers, appears like an option to replace the synthetic ones in composites with polimerics matrices. Besides the environmental advantages, the lignocellulosic fibers have economical and some properties advantages like the low density in comparison with the synthetic fibers. Nowadays the lignocellulosic are used in industries, like the automobile and aerospace. This objective of this study was to analyze the absorbed impact energy of the composites reinforced with PALF fibers. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. The results showed increase in the absorbed impact energy with the increase of the percentage of fiber incorporated. The fracture surface of the specimens were analyzed by SEM (scanning eléctron microscope) and indicates that the PALF fibers act as reinforcement for the polyester matrix.

Mar 1, 2017

By Marcos V. F. Fonseca, Djalma Souza, Luiz G. X. Borges, Sergio Monteiro, Caroline G. de Oliveira, Ygor M. de Moraes, Janine F. de Deus, Frederico M. Margem

Recently, the natural fibers have been studied as alternative reinforcement material to the use of synthetic fibers. Aiming to improve the properties of natural fibers composites, it is investigated the use of natural fibers fabrics, since they provide multidirectional reinforcement and enables the introduction of a larger fiber volume fraction. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volumefractions offabric made of Ramie, a highly resistant lignocellulosic fiber. The specimens were made by pressing the fabric with liquid resin to guarantee total impregnation, and then cutting the fabric in the mold format. Finally ,the fabric layers were placed into the mold with the liquid resin and catalyst. They were cured for 24 h and tested. The results revealed an increase in the tensile strength and almost no effect in the elastic modulus with the increase of fabric volume fraction.

Mar 1, 2017

By Yunhua Gan, Xiaowen Chen, Meilong Hu, Haige Li, Yang Tong

Ethanol is a kind of renewable fuel, which can be produced from biomass and applied in many energy areas, such as motorcar. The combustion of ethanol in meso-scale is facing great challenges, such as great heat loss, poor stability, and low combustion efficiency. Electro-spraying technique is an effective method to atomize liquid ethanol due to its great advantage of monodisperse and uniform characteristics. In present study, electro-spraying was applied in liquid meso-scale combustor to produce very small droplet diameter and uniform droplet distribution. Experiments were carried out based on nozzle-ring-mesh electrode structure using pure liquid ethanol as fuel. Electro-spraying characteristics were measured by Phase Doppler Anemometer (PDA) under different nozzle voltages, ring electrode voltages, flow rates, and steel mesh positions. The results may be helpful to the design of new meso-scale electro-spraying combustor using renewable liquid fuel.

Mar 1, 2017

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989

By Chang Chia -Fu

The generic structure of our bimesogens is shown in and for a typical blue-phase mixture of the type we describe here. We use mixtures of the ratio 33.4% (n =2.6), 34.1% (n =6.57), 36.6% (n= 11.15) with of the high twisted power (HTP) agent BD H1381(available from Merck Chemicals and described in ref. We then studied the electric-field dependency of the selective reflection in BP I* at 20.7 °C by applying increasing and the decreasing pulsed alternating current (a.c.) electric fields (100 Hz).

Jan 1, 2006

By J. R. Addison

Commissioned in September 1987, the Phelps Dodge Morenci, Inc. (PDMI) Central Electrowinning (EW) Tankhouse bas undergone two major expansions in its eleven-year history. A third tankhouse renovation, which began in November 1998, entails complete conversion of the 548-cell facility from a copper starter sheet based operation to Mt. Isa Process stainless steel mother blank technology. This paper outlines the operating history of the Central EW Tankhouse and reviews the conversion process, the rationale that led PDMI to undertake this project, and describes various design optimizations which have been implemented during the conversion.

Jan 1, 1999

By G. Ríos

Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975 the old blast furnaces were replaced by the Outokumpu FSF technology. During the last 30 years, through several expansions and technical modifications, the production has increased up to 300,000 tpy of new copper. This paper describes the developments on the control of impurities that have been made to fit new situations, such as a new artificial gypsum plant, a new electrolyte treatment plant or different secondary materials handling management.

Jan 1, 2006

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012