Search Documents

By I. Moscoso, R. Padilla, M. C. Ruiz

Antimony and arsenic are impurities in copper concentrates found normally as stibnite (Sb2S3), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4). When copper concentrates contain appreciable amounts of As and Sb, they must be removed before smelting to avoid environmental pollution. Oxidizing volatilization roasting at 500–700 °C has been used to eliminate these impurities. However, only a fraction of Sb volatilizes in those conditions; thus, a more effective process to eliminate antimony from concentrates is needed. In this study, the chloridizing roasting of Sb2S3 using CaCl2–O2 was investigated to remove the antimony from concentrates. XRD analysis of calcines indicated that the overall reaction could be written as: Sb2S3 þ3CaCl2 þ6O2 ¼ 2SbCl3 þ3CaSO4 Temperature and oxygen partial pressure have a significant effect on the rate of reaction. An estimated conversion of about 90% was obtained at 750 °C, 5.4% oxygen in 20 min. High oxygen concentrations arrest the advance of the reaction forming various antimony oxides including Sb6O13, Ca5Sb5O17 and Sb2O4.

Mar 1, 2017

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Nils Eivind Kamfjord, Halvard Tveit, Ingeborg Solheim

"Because of its negative environmental effect the attention towards NO emissions increases. This again leads to new demands from the authorities for better surveillance and control of emissions. Earlier and recent industrial measurements towards FeSi- and Si-metal furnaces reveal quite high NO-emission. The NO is believed to be produced in the combustion zone above the furnace surface, mainly as thermal NO.In order to expand the knowledge on NO-formation in silicon metal production, a pilot scale experiment in a 440 kVA silicon furnace has been carried out. The experimental set-up was designed with a view to be able to copy and manipulate the formation mechanisms for NO by controlling the flow of false air into the off-gas system.The resulting NO-values corresponding to the different air inlet to the furnace top, show significantly differences between the different air inlet geometries.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2). Since combustion of fuels, such as gasoline, diesel, bio diesel, propane, coal, and ethanol, forms NOx the dominating contributors to NOx emissions are the on-/offshore transportation industry and power generation based on fossil fuels [1]."

Jan 1, 2012

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By Mokka Rao, Asdrubal Serrano

"A mathematical model is developed which describes the movement of the minerals present where the vertical and angular velocities are related with the different operative parameters involved in the process of separation of silica from iron ore, which permit maximise the capacity of the spirals to obtain major productivity. The process is realised in two steps, of the rough dressing and other cleaning. Through the results obtained for chemical analysis of the final products of each spiral and the equation of movement of particles, it is proved the applicatibility and efficiency of mathematical model to operating parameters of the spiral. Moreover, it is determined though the recuperation of the final products of quality in the use spiral HC 1870 and HG 8/7. INTRODUCTIONThere is prospetive of increasing the production the iron ore in agreement with the demand of siderurgical proyects united with the external demand of quality 40 million tons per year. The Ferrominera de Orinoco Company is experimenting two types of modem spirals, Humprey (HC 1870) and Reichart (HG 8/7) which have limited capacity. For this reason this investigation designed a mathematical model with which larger units can be designed for increasing the capacity of the spiral."

Jan 1, 1999

By A. V. Tarasov, A. D. Besser

A processing flowsheet has been developed for treating substandard lead-containing polymetallic bulk concentrates and intermediate flotation products containing precious metals, which comprises oxidizing roasting in a calcination kiln and electrothermic smelting generating low volumes of off-gas. The proposed flowsheet also incorporates a dust collection system and sulfur dioxide recovery from off-gas. It is proposed to implement this process by using a reaction smelting technique. For this purpose, the charge to be fed to the smelting furnace after its calcination in a drum-type rotary kiln must have a ratio of sulfide sulfur to sulfate sulfur of at least 1 :2. Electric smelting makes it possible to produce lead bullion that also collects the precious metals contained in the feed, as well as copper-lead matte and slag containing zinc. The recovery of lead into lead bullion and into matte is approximately 83% and 14%, respectively (thus the overall recovery is 97%); the total recovery of gold and silver into lead bullion and matte is 98%; th\lt of copper into matte is 89%; the recovery of zinc into slag is 96%; and that of sulfur into sulfuric acid or gypsum is 90%. After the recovery of zinc from slag, the latter can be utilized in the construction industry.

Jan 1, 2000

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

By V. L. Richards, S. N. Lekakh, S. A. Dutler

"This study presents determination on the thermal properties of investment casting shell molds used in casting process modeling. Superheat and latent heat from solidification and cooling of a casting can either be accumulated by ceramic shell for thin-walled casting or transfer to environment for massive casting. Heat capacity and thermal conductivity both play important roles in casting solidification. Thermal properties of ceramic shell depend on shell composition and fabrication techniques as well as thermal history during shell preparation process due to multiple phase transformations. Inverse modeling was combined with corrected Laser Flash method to determine the applicable thermal properties of the shell during casting solidification. Pure nickel was poured into ceramic shells containing two thermocouples and experimental cooling curves were obtained. These curves were then fitted to the model by adjusting temperature dependent heat capacity and thermal conductivity.IntroductionCasting solidification in investment casting shell affected by shell thermal properties including specific heat capacity and thermal conductivity. For relatively thin walled casting, most of the melt superheat and part of latent heat are accumulated by the shell. This process is mainly controlled by shell heat capacity. In the case of massive casting, significant part of latent heat transfers to environment through the shell so that this process is mainly controlled by shell thermal conductivity."

Jan 1, 2012

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young's moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998

By S. Sugiyama, M. Kiuchi

"New metal working processes, such as the mashy-state mixing, mashy-state forging, mashy-state rolling and mashy-state extrusion are developed and applied to manufacture the so-called particle reinforced metals, fiber reinforced metals, particle reinforced cladding metals and so forth. These metal-ceramics composites are made of metal sheets, metal powders, ceramics particles and ceramics fibers. The mashy-state processes are also used to work those composites into bars, wires, tubes, plates, sheets, machine parts and other products. The working conditions necessary to manufacture sound composite products are clarified and the mechanical properties of the products are investigated. Through the investigation, it becomes clear that the mashy-state processes are useful and effective to manufacture metal-ceramics composites. It is al so known that these processes may be applied in various ways to development of new metal matrix compounds. IntroductionThe so-called metal-ceramics composites and processes to manufacture them are now being widely investigated in order to comply with increasing demands for new materials with novel and excellent mechanical properties and functions. The metal-ceramics composites are expected to have superior characteristics with respect to the elastic modulus, hardness, anti-wear resistance, high temperature strength and other mechanical properties to those of conventional metallic materials.The present authors ha v e been investigating into new metal working processes which are based upon the characteristics of metals and their alloys in the mashy-state. In the mashy-state, the metal (or alloy) includes both of the solid and liquid components. According to the fact that the partial melting takes place and the liquid component usually exists at grain boundaries, the metal in the mashy-state has quite different mechanical properties from those of the metal in the solid-state. Because of that the bonding force among grains is very weak due to the partial melting occurred at grain boundaries, the mashy metal has distinctively low flow-stress and high deformability. The mashy metal splits into grains or particles and sticks to others very easily. It is so soft as to be stirred up just like a lump of sherbet, but it is sufficiently viscous to be mixed up with other materials, such as ceramics particles and ceramics short-cut fibers."

Jan 1, 1988

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By Masayasu Kawahara, Toshiyuki Kozuka

"Lorentz force, which has the functions of wave suppression and mixing control, is very useful for many metallurgical processes. In this paper, it is found that vertical Lorentz force which can change 'the gravitational force is able to modify the dispersion relation of the surface wave generated by gravity and also modify the instability phenomena on the interface so that the lower layer can be scattered into upper layers to realize the strongly mixed region.IntroductionIn metallurgical industries, recently, a new direction of process developments is required backed not only by severer operating conditions, e.g. small amount production, rapid refining, etc. but also by environment and energy problem. Because almost technologies in conventional processes have saturated, an innovative process, which can break the limits in the conventional processes, is now strongly required. Especially, controlling of mixing phenomena between two liquid phases is considered to be one of the most important technologies for the promotion of slagrnetal reaction, wave suppression, etc. On the other hand, electromagnetic forces which have various functions have been applied to many processes. And Lorentz force is able not only to suppress the wave motion of molten _metal surface but also to promote the mixing or separation of two liquids. In this paper, new controlling methods of mixing phenomena between two liquids are proposed, where a direct electric current and a stationary magnetic field are utilized. Vertical Lorentz force due to the interaction between the electric current and the magnetic field can modify the gravity force so that the dispersion relation of surface wave and the instability on the interface can be change to improve or develop the innovative processes(l,2).In case that a direct electric current is imposed on two liquid layers with a stationary magnetic field, Lorentz force of each layer becomes different due to the difference of electrical conductivity. If Lorentz force acting on the lower layer is stronger than that on the upper layer, resonance frequency of the wave motion on the interface due to the gravity can be shifted from the frequency of a outer disturbance to suppress the wave motion. And also, the lower layer can be scattered into the upper layer as liquid particles by an instability phenomenon."

Jan 1, 2000

By Zhang Jianliang, Zuo Haibin, Gao Bing, Wang Zhe

"As a result of the shortage of coking coal and the quality decrease of coke, it is important to know how to make better use of highly reactive cokes. The co-gasification behavior of highly and lowly reactive coke for blast furnace is investigated. The results show that: In the middle stage of reaction, the weight loss ratio of highly reactive coke reacted together with lowly reactive coke is higher than that of it reacted individually. However, the weight loss ratio of lowly reactive coke is lower. The weight loss ratio of highly and lowly reactive coke is almost the same as that of the weighted average. The scanning electron microscope analysis indicated that the reaction degree of surface and interior of lowly reactive coke is relatively uniform with the reaction time increased. And the reaction degree of surface of highly reactive coke is obviously higher than that of interior.IntroductionIn blast furnace iron making process, coke functions as heat supplier, reducing agent, carburizer and skeleton. With development of blast furnace iron making technology, the skeleton function of coke is becoming more and more important in requirements of large scale furnace and high pulverized coal injection. High reactivity coke is usually produced by cheap coal with bad quality, and is not good for blast furnace process. The reactivity of coke is mainly determined by the coals used, and the resource of good quality coking coal is limited and is non-renewable. In order to fulfill the need of blast furnace, a lot of research have been done to improve coal matching using new kinds of coal to enlarge resource, in which coking coal and fat coal are reduced, whereas low price coal with bad caking property are used to lower the cost, and this would inevitably increase the reactivity of coke [1-4] Blast furnace iron making would still be the main stream for a predicted future, and high reactivity coke would correspondingly be used more and more, so it has great importance to study how to use high reactivity coke in blast furnace."

Jan 1, 2013

By Matthias Schnitzler, Herbert Pfeifer, Ralf Bolling

"To transform metals high temperatures are usually needed. A fast and efficient heating can reduce the C02 emitted. The fastest way to heat metals is called direct flame impingement (DFI). The flame impinges upon the item being heated. For this method it is important to know the shape and length of the flame. Laser-induced fluorescence (LIF) technology allows measurements of a two-dimensional field without influencing the reaction or the flow. Commonly used is the measurement of OH-radicals, an indicator of the reaction zone.In the presented study measurements of a turbulent diffusion flame are shown. The position of the reaction zone and the influence of the distance between the item being heated and the burner are investigated. Conventional measurements and LIP-measurements are compared and the potential of DFI to increase the efficiency of heating metals is discussed.IntroductionDuring industrial heating processes a fast and efficient heating technology is required. Two important aspects are the NOx emission and the energy efficiency. The direct flame impingement (DFI) technology has the highest heat transfer rate possible with a gas/air flame. The turbulent high velocity flame jet impinges upon the item being is heated [ 1]. Due to the high heat transfer rate furnace and exhaust gas temperatures are lower. Therefore the energy efficiency is increased and the amount of NOx emitted is reduced.Hydroxyl- (OH-) radicals are an intermediate product that is generated during the combustion of hydrocarbons [2]. They are commonly considered as an indicator for the reaction zone and position of heat release. Figure 1 shows the hydroxyl-mole fraction in dependence of the distance along the gas flow. The figure clearly shows how fast the OH-concentration increases in the reaction zone. Figure 1 also shows that OH-radicals are present in the post combustion region, however in smaller concentration [3].The laser-induced fluorescence technology serves to measure the spatial distribution of OH-radicals in a two dimensional cross-section area of the flame. Therefore the flame dimensions and location can be determined with high spatial resolution without influencing the flow or the reaction [ 4,5]."

Jan 1, 2012

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011