Search Documents

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By Stein Tore Johansen

The flow of a liquid through a large grain filter has been considered. An improved form of the fluid dynamic equations describing flows through porous media is proposed. The theory is applicable to all Reynolds numbers. Particulate inclusions are described by passive scalar fields where only very simple mechanisms for particle removal are included. However, the deposition of particles are allowed to change the "porosity" of the filter. Hence, the flow pattern through the filter will change as the filter ages. The theory is employed to the filtration of aluminum in an industrial grain filter. The model shows that the filter is not effectively designed and there is room for considerable improvement. The dynamic "aging" process of the filter is shown to change the filtration from bed filtration to cake filtration. Finally, the predicted inclusion collection efficiencies are compared to efficiencies measured in an industrial filter. The predicted initial efficiencies are in very good agreement with experimental results.

Jan 1, 1990

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior of TiO2 nanoparticles was thermogravimetically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanoparticles, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500 °C at heating rate of 1O 'Cumin. The weight increase curve showed a maximum of ca 30 wt% at around 750 T and then gradually decreased to ca 12w% at 1000OC. This would be caused by the formation of TiS2 followed by the decomposition of TiS2 to lower sulfides, such as Til.08S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanpparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By Nina Bianco, Diana Drinkwater

MetSkill is a professional development program for metallurgical engineers that integrates with normal duties in their first one or two years of service. Graduates work together on a structured technical project, facilitated by specialists and supported by formal learning, and ultimately reported to their technical managers. The program enables graduates to “fill the gaps” in their undergraduate education, which is increasingly pertinent as engineering degrees become more general. Participants report that they enjoy the focus on more challenging (rewarding) aspects of their jobs and feel more confident about problem solving. Sponsor companies add that the relationships developed with external technical specialists enhances opportunities for innovation and development. MetSkill was delivered to two major resource companies in Australia in 2012. This paper provides an outline of the program and the reasons for its success, and demonstrates how the learning model could be applied to groups of graduates in other engineering disciplines.

Jan 1, 2014

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By Eun-young Kim

Electrogenerated chlorine leaching of waste printed circuit boards was investigated in hydrochloric acid solutions. The pulverized printed circuit board contained about 37.6% of metal component, in which copper was about 83.6%. The leaching rate of copper was greatly affected by current density and agitation speed. The leaching of copper up to 98% was achieved at 20 mA/cm2, 50?, 180 minutes, and 600 rpm in 1M HCl solution. Increasing agitation and lowering current density enhanced utilization efficiency of electrogenerated chlorine. Leaching of copper was suppressed at initial stage, while the minor metal elements, such as aluminum, lead, and tin, were dominantly leached out.

Jan 1, 2006

By Jim Sundal

Primary steel manufacturers using electric arc furnaces generate one of the largest hazardous waste streams nationwide. The waste stream, known as electric arc furnace dust, is a listed hazardous waste with the designation K061. Oregon Steel Mills, Inc., (OSM) of Portland, Oregon, has implemented a process known as Glassificationn, which uses KO61 as an ingredient in an onsite recycling process. Because OSM was able to demonstrate that the Glassificationm recycling process beneficially uses all toxic constituents in the electric arc furnace dust and that the recycling process produces marketable products, the process is not subject to Resource Conservation and Recovery Act (RCRA) permit requirements. The marketable products manufactured using Glassificationn include roofing granules, ceramic glazes and colorants, abrasive blasting media and, more recently, synthetic slag fluidizers. The purpose of this paper is to identify the regulatory issues for recycling hazardous waste and demonstrate that OSM glass frit is effective as a slag fluidizer in primary steel manufacturing.

Jan 1, 1994

By Lin Yang, Yuanbo Zhang, Zhuoxuan Li, Guanghui Li, Jinghua Zeng, Tao Jiang

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 oC, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Jan 1, 2015

By Isabella Lancellotti, Fabrizio Passarini, Luisa Barbieri, Fernanda Andreola, Ivano Vassura, Luciano Morselli

"The techniques able to incorporate wastes by means of a heat treatment present the advantage to fix the residue with chemical bonds. Among these techniques there are vitrification and sintering which are characterised by different operating temperatures in the range of 950-1500°C and the involved raw materials develop silicatic crystalline phases and glassy matrices capable to immobilize heavy metal contents in the waste matrix. In this work incinerator bottom ash, polishing and glazing ceramic sludges have undergone to thermal treatments in order to valorise the waste as secondary raw material for the obtainment of re-products. The chemical efficiency of the process adopted has been evaluated by comparing the results of release tests applied to the as-received wastes and to the thermally treated materials in order to verify the effectiveness of the different matrices to fix the waste components.IntroductionVitrification is one of the most promising technological options for the treatment of some kinds of waste. The high temperature involved in the process (1200-1500°C) leads to the complete destruction of organic pollutants, such as dioxins, and glassy network formed can incorporate heavy metals. Some vitrification processes naturally occur: glasses produced by volcanic eruptions, such as obsidians (Na2O-K2O-Al2O3-SiO2) and basaltic (CaO-MgO-Al2O3-SiO2) rocks, are basically inert materials even when they contain toxic elements, because these are embedded in an extremely stable glassy matrix. The disadvantage of vitrification is that it is an energy-intensive process involving relatively high costs, therefore its use is better justified if a high-quality product with optimised properties can be fabricated. The most effective way to improve the properties of the vitrified material is the transformation into glass ceramic. This is a fine-grained polycrystalline material (typically from 50% to 98% of the volume may be crystalline) formed when a glass of suitable composition is heat treated and hence undergone to controlled crystallisation (phenomenon named devitrification). The three key variables in the design of a glass-ceramic are: glass composition which controls glass viscosity related to the effectiveness of nucleation and rapidity of crystallisation; glass-ceramic phase assemblage (that is, the types of crystals and the proportion of crystals to glass) which is responsible for many of the physical and chemical properties; nature of the crystalline microstructure (crystal size and morphology and the textural relationship among the crystals and glass) which is the key to many mechanical and optical properties. In particular, a partly crystalline material can be obtained by powder sintering."

Jan 1, 2008

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a suitable and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hardburned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and creep study was completed, accompanied by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1991

By R. P. King

The linear intercept distributions provide unambiguous and accurate characterizations of the texture of mineralogical materials. The relation between the measured linear intercept distributions and the spatial correlation function is shown to be given by: in the Laplace Transform domain. The linear intercept distributions of the two phases in a low- grade chromite-serpentinite ore were measured. and the spatial correlation functions for both phases were evaluated using the above relation. The correlation functions are the primary relations for integral geometric models of mineralogical texture and this work demonstrates the relation between the 10 stereological model and the 3D integral geometry model for mineral liberation.

Jan 1, 1991

By Jefferson Caponero

The tire is an expressive component of Municipal Solid Waste, manly when its occupied volume is considered. Its treatment by pyrolysis stands for a list of advantages, such as: landfill releasing and a production of a high quality fuel. The exploitation of new natural resources is becoming more difficult each day, basically due to the environmental damages caused by this type of activity. This work presents a study on the thermal behaviour of Brazilian tires using thermogravimetric analysis and differential thermal analysis, in order to optimise the pyrolysis process of tires. Samples of I to 2 mm were investigated at atmospheres of nitrogen, argon, oxygen and mixtures of these gases at temperatures up to 1273K, under heating rates between 1 to 50 Klmin . The results showed that the behaviour of each sample is related to both the atmosphere composition and the heating rate.

Jan 1, 2001