Search Documents

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By Dong-sheng Li, Hong-ming Long, Tie-jun Chun, Chao Ning, Zhen Wang

Iron ore sintering is an essential process in modern iron and steel production. It has the largest emission of the PM (particulate matter) in the iron and steel industry, accounting for about 40% of the total emission. The physical and chemical properties of PM 10 and PM 2.5 in the iron ore sintering were introduced, and the research development of PM emission reduction was also summarized. The potential future development of PM emission reduction by chemical agglomeration and capture in the iron ore sintering process was also carried out. The interface chemistry relationships between PM and polymer, such as sodium carboxy methyl cellulose (CMC) and polyacrylamide (PAM), in agglomerates were also investi- gated in this paper. It is signi ficant to reveal the characteristics of PM and develop the emission reduction technology of PM for the cleaner production of iron ore sintering.

Mar 1, 2018

By J. E. Dutrizac

The mineral forms of silver, lead and cadmium in the zinc concentrates and the various roaster products made by the Kidd Creek Division of Falconbridge Inc. have been elucidated. In the concentrates, all three elements occur mainly in sulphide form, either in solid solution in the principal ore minerals or as discrete mineral grains. During roasting, Ag, Pb and Cd are preferentially concentrated in the hot cyclone and ESP dusts of the roaster train. Silver is converted to <0.5 µm grains of silver metal and to Ag2S04 which dissolves in or impregnates silicates. Lead is converted to Pb-bearing silicates or to PbS04 and PbO which are present either as tiny free grains in ZnO or as an intergrowth with lead silicate. Lead is also a minor constituent of the ferrite phase. Cadmium occurs mostly as cadmium-bearing zno and ZnFe2o4 , but a significant amount also reports as Cd-bearing silicates or zinc sulphate.

Jan 1, 1990

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By Jason M. Porter, Douglas L. Porter, David L. Olson, Travis W. Koenig, Van S. Blackwood, Brajendra Mishra, Robert D. Mariani

"Traditional alloy theory models have been applied relative to the three solid phases of uranium: alpha (orthorhombic), beta (tetragonal), and mainly gamma (body centered cubic)[l]. The Darken-Gurry and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer have been used to predict the behavior of four types of solutes: 1) Transition associated with alloying in and containment of the uranium fuel 2) Transuranic elements in the uranium 3) Rare earth fragmentation elements (lanthanides) 4) Transition metals and other fragmentation elements. Using these solute map criteria, elemental behavior have been predicted as highly soluble, marginally soluble, or immiscible (intermetallic phase formers) and have been used to compare solute effects during uranium phase transformations. The overlapping of these solute maps are convenient first approximation tools for predicting alloy behavior.IntroductionAn investigation is in progress to determine the role of various solute elements on size and shape of the 'Y phase field range for uranium to optimize the burning and material processing of nuclear fuel is in progress. Traditional alloy theory models based on correlations to elemental electronic and crystal properties are used to predict solubility and micro structural formation. The effectiveness of this model is based on microstructure property correlations. Darken and Gurry, and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer, models have been used to describe solute solubility with respect to uranium based the on correlation between elemental electronic structure and uranium phases. The alpha (orthorhombic), beta (tetragonal), and gamma (body centered cubic) phases have different solubilities for specific alloy additions as a function of temperature. Using the method of Waber, ellipse diagrams classified those solutes that should have broad solubility in the allotropes of uranium[2]. The predictive diagrams are made from four different correlations:"

Jan 1, 2012

By P. Mazumder

Numerical analysis is carried out to examine the effects of thermosolutal convection on the formation of complex patterns in directionally solidified binary alloys. A finite-difference analysis is used for dynamic modeling of a two-dimensional prototype of Vertical Bridgman system that takes into account heat transfer in the melt, crystal, and the ampoule; melt flow and solute transport. Actual temperature data from experimental measurements are used for accurately describing the thermal boundary conditions. A range of complex dynamical behavior is predicted in the melt flow due to flow transitions and this is found to be directly related to the spatial patterns observed experimentally in the solidified alloys. The model is applied to single phase solidification in the Al-Cu and Pb-Sn systems to characterize the effect of convection on the macroscopic shape of the interface. The application of the model to hyper-peritectic alloys in the Sn-Cd system shows that the presence of oscillating flow can give rise to a novel convection induced microstructure in which a tree-like primary phase in the center of the sample is embedded in the surrounding peritectic matrix.

Jan 1, 1999

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By G. Lissens

In this work the electrochemical combustion of dissolved organic species in a single compartment cell containing a titanium mesh cathode and a boron doped diamond anode has been studied, The organic molecules involved were complexing agents such as EDTA (ethylenediaminetetraacetic acid) or NTA (nitrilotriacetic acid) used in metal plating shops and bright nickel plating bath additives, From batch experiments, it is shown that complete decomplexing of EDTA and NIA is feasible. Complete TOC (Total Organic Carbon) removal from solutions containing 0.01 M EDTA, 0.02 M NTA and bright nickel plating bath additives could also be achieved. Recycling experiments show that decomplexing of EDTA and NTA solutions can be obtained at an average electrical energy input of ~20kWh.kg-1 of complexing agent. Decomplexing rates of respectively 3.l3 mmol.Ah-1 for EDTA and NTA have been obtained, The Instantaneous Current Efficiency (ICE) was 71% for EDTA and 95% by NTA, Simultaneous recovery of Cu from a 0.01 M Cu-EDTA solution has also been evaluated. A solution (1.8 dm3) containing 0.01 M EDTA and 528 ppm of Cu was treated in a single compartment cell at a current density of 2 A.dm-2. 73% of the TOC could be removed and a final copper concentration of 8 ppm was obtained.

Jan 1, 2003

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By Leiting Shen

The thermodynamics of tungsten ore decomposition in mineral acid and alkaline solutions were studied. The published thermodynamic data of tungsten minerals were collected and assessed. The Gibbs energies of CaWO4 (−1538.43 kJ/mol), FeWO4 (−1053.91 kJ/mol), MnWO4 (−1206.08 kJ/mol), H2WO4 (−1003.92 kJ/ mol), and Na2WO4 (−1455.58 kJ/mol, aq) at 25 °C were adopted in the calculation using HSC software. The results show that CaWO4 is decomposed more readily in Na2CO3 solution than in NaOH,while FeWO4 andMnWO4 aremore reactive inNaOH solutions. Froma thermodynamic point of view, tungsten ore decomposes easily in acid solutions despite most ΔGo T increasing slightly with temperature. Oxidizing Fe2+ to Fe3+ in acidic solutions facilitates decomposition of FeWO4, and the reaction of CaWO4 in H2SO4 solution occurs more easily than in other mineral acids, due to the formation of sparsely soluble CaSO4. The results fit well with the experimental data and industrial experience previously reported in the literature.

By Mamoru Kuwahara, Tomohito Taki, Masamichi Sano

"Theoretical basis and experimental results on ultrasonic separation of dispersed inclusions from molten metal are outlined. Transitional formation of an ultrasonic standing ·wave field in a liquid bath is numerically predicted based .on the wave equations. Numerical solution of the equation of motion of a fine particle in a standing wave field indicates that the inertia term can be neglected during conventional ultrasonic separation of fine particles: Analytical solutions for the position at which particles are coagulated the minimum power for separation, and the ultrasonic separation time are derived to incorporate such key process parameters as the density difference and the acoustic energy density exerted. Cold model experiments have been carried out to observe ·transitional coagulation of polystyrene particles in an aqueous sugar solution with the incidence of standing ultrasonic plane wave. Experimental results agree well with the theoretical predictions.IntroductionDespite of recent progress of fundamental and applied researches in metallurgical systems, advanced materials· with less inclusions and better properties may demand more innovative processing in a: molten state. It may be realized by applying electromagnetic and/or ultrasonic external fields to the systems. The present authors1)·2) have been proposing : new methods of ultrasonic processing of materials based on such phenomena as acoustic streaming, acoustic radiation pressure on dispersed phase in a standing wave field, and the cavitation in liquid associated with use of high-intensity ultrasound and so on. Taking account of common physical natures between ultrasound and sound wave, we call such · a processing assisted by acoustic wave as ""sonoprocessing"". This report ·deals with some theoretical and technological aspects on the ultrasonic separation of fine particles from liquid, which could become an important operation to produce clean materials. Fundamental theory and ·supporting experimental results will be given below to give an insight into the liquid metal sonoprocessing."

Jan 1, 2000

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By J. M. Shneerson

At Gipronickel Institute a technological flowsheet of pressure leaching of copper from rich copper concentrates (i.e. containing: Cu -59-75%; Ni -D.5-4.64%; Fe -D.2-J.3%; S -21.8-26.9%) was developed. As a result, the possibility of deep decomposition of copper-containing minerals with extraction of elemental sulphur (up to 90-95%) was established. The obtained sulphur concentrates contain 80-90% of elemental sulphur, which can be separated from sulphide residue through autoclave melting and settling. As a rule, sulphide concentrates remaining after extraction of sulphur contain up to 1-2% of noble metals. The sulphide concentrate can be purified to the level of rich concentrates or pure metals using the well-known methods as in the case of tankhouse slimes. The presented research specifies the parameters of main operations: pressure leaching and sulphur extraction. It was established that 98% of copper could be transferred into solution at temperatures of 108-1 10°C and oxygen partial pressure 0.4-0.6 MPa. Experiments were carried out in autoclaves of various volumes using the products of nickel matte processing.

Jan 1, 2003

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991