Search Documents

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By R. E. Aune

In the present work, a critical assessment of the thermodynamic information available for the ternary system Ni-W-0 has been carried out; This was complemented by experimental measurements of the standard Gibbs energy of formation of the ternary compound NiWO, by solid state galvanic studies involving Zr02-CaO solid electrolyte. The assessed thermodynamic data, together with the phase diagram information available in literature, were employed to generate the ternary phase diagram for the system Ni-W-0 in the temperature range 1073-1273 K. The calculation of the phase diagram was carried out by computer optimization according to the "CALPHAD" method. The computed phase diagram has been confirmed at isothermal sections by identification of the phases present in samples equilibrated at defined temperatures.

Jan 1, 1994

By J. Huisman

With the introduction of ever-stricter environmental operating guidelines, capital expenditure restrictions and operational budget cutbacks, the biological method of SO2 removal becomes more and more attractive. Biological treatment of dilute flue gases is a more cost effective technology in comparison to conventional sodium hydroxide scrubbing. Although the investment costs for sodium hydroxide scrubbing is lower, the operational costs are significantly higher. In addition, the end product of the biological installation is sulfur instead of sodium sulfate; and no further wastewater treatment of the bleed from the biological installation is required since heavy metals are removed simultaneously. Another option for the treatment of SO2 containing gas at a sulfuric acid plant is the production of extra sulfuric acid of the discharged SO2 by applying an additional converter. Comparing biological treatment with this option shows much lower investment costs for the biological installation. Sulfur is produced which can be converted to sulfuric acid, so the bio-route will be more cost-effective than an additional converter. In principle, the biotechnological gas cleaning system is an integration of an absorber with a wastewater treatment facility. In the absorber, the SO2 containing gas is brought into contact with the washing water. The effluent absorber liquid contains a mixture of sulfite and sulfate that is converted into elemental sulfur. This conversion takes place in an integrated system; first, the sulfite/sulfate mixture is converted anaerobically into sulfide; secondly, the sulfide is converted aerobically into elemental sulfur. Subsequently the sulfur is separated and the water is returned to the absorber. Due to the buffer capacity of the washing water, removal efficiencies over 98% are possible. In addition to SO2 removal, it is possible to convert for example other bleeds streams such as scrubber acid or weak acid to sulfur in the same SO2 installation. Recent evaluations concluded that biological desulphurization of flue gases is not only economically attractive in comparison to convention sodium hydroxide scrubbing but also in comparison to gypsum producing systems and even seawater scrubbers. This paper describes the technological and economical viability of biological flue gas desulphurization.

Jan 1, 2005

By F. F. Aplan, G. Simkovich

"A review is given of the effects of solid state point imperfections upon a number of mineral benefication processes and a metal extraction process. It has been found in numerous flotation studies that small amounts of aliovalent impurities (dopants) in binary compounds may show major effects upon flotation behavior. Both semiconducting and ionic conducting compounds are affected. These effects are also seen in hydrometallurgical studies as well as in electrostatic operations. Additionally, de-copperization of lead melts appears to be strongly influenced by similar defects. It is hypothesized that the effects observed in these studies are present in actual operations and should be considered in designing processes. A few speculations concerning future efforts are advanced. IntroductionImperfections [point (e.g., vacancies, interstials, quasi-free electrons, electron holes, impurity ions), line (e.g., dislocations), two dimensional (e.g., grain boundaries) and three dimensional (e.g., 2nd phases) defects] are generally present in solid materials and these imperfections may, and often do, have important effects upon a variety of properties and processes. In general, one may, in most cases, attain elimination of three dimensional defects by a separation process of one type or another (e.g., gravity, electrostatic, magnetic, flotation, hydrometallurgical etc.,). Thus, this type of defect has rarely been investigated in a systematic fashion. Two dimensional defects are always present in non-single crystal materials but have also escaped systematic studies in processes primarily because the control of such defects is not easily attained. Line defects are non-equilibrium entities which are present in ill-defined quantities so that they present a variable that cannot be easily controlled although through careful systematic experiments one can attain some reproducible relations pertaining to this type of defect.Contrary to the lack of studies concerned with the effects of 1, 2 and 3 dimensional types of defects there has been some activity concerned with point defects and their effects upon a number of mineral/metallurgical processes, especially flotation processes. Thus, this article will present a review primarily of point defects in relation to their effects upon flotation although other processes and defects will also be mentioned."

Jan 1, 1988

By Paul L. Wichlacz

A mathematical model of growth and ferrous iron oxidation for attached bacteria was applied to rotating biological contactor (RBC) units treating acidic mine drainage. The model describes attached bacterial growth as a saturation function, where the rate of substrate utilization is determined by a maximum substrate oxidation rate constant, a half saturation constant, and the concentration of substrate within the RBC. The maximum oxidation rate constant was proportional to flow rate and the substrate concentration in the reactor varied with influent substrate concentration. The model was tested at three separate sites and with three different size RBC units. The ability of the model to predict the rate of iron oxidation under all test conditions was significant. The accuracy of the model was found to be affected by unit size and vary with specific test site.

Jan 1, 1985

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By Klas G. Hultbom

Mercury is present as trace contaminant in many raw materials for metallurgical plants. When such materials are treated with pyrometallurgical processes the mercury is volatilised. Mercury has a high vapour pressure, even at low temperatures, and therefore it is removed only partly by normal gas cleaning processes. The Boliden Norzink scrubbing process removes elemental mercury by converting it to calomel. It is widely used in the base metals industry. This paper gives examples of the application, and also outlines the background for the development of the process. Another technology developed by Boliden for mercury removal is the Selenium filter. This is a fixed bed filter based on the reaction between elemental gaseous mercury and selenium, by which mercury selenide, HgSe, is formed. The mercury selenide is a highly stable compound with extremely low solubility in water and very low vapour pressure. Mercury is removed selectively without any side reactions. Special applications for the selenium filter technology include mercury removal from gases containing sulphur dioxide and geothermal off-gases.

Jan 1, 2003

By Deepak Gupta, R. Kageyamat, J. W. Evans

"In electromagnetic casting, a liquid metal pool is partly supported by electromagnetic forces resulting from the interaction between induced currents and an alternating magnetic field. Stability of the metal surface is of paramount importance if the cast ingot is to be free from surface defects. Prior work by Garnier and Moreau had suggested that the magnetic field has no influence on the surface stability, but a more complete analysis at Berkeley suggested that surface perturbations are destabilized by the magnetic field once a critical magnetic field is exceeded. More recently we have employed a modified version of the software SOLA to compute the behaviour of a melt surface in the presence of an alternating field. The computed results support the theoretical analysis in predicting an unstable surface. Experimental work is now in progress to examine the stability of a mercury pool in the presence of an alternating field. Introduction and Previous InvestigationsElectromagnetic casting (EMC) is a technique widely employed in the aluminum industry to produce ingot for subsequent rolling. It is a ""continuous"" casting technique (illustrated in Fig. 1) producing ingots several meters high (and perhaps 1m by 2m in horizontal dimensions) at a casting speed of one or two mm. per second. The technology has gained acceptance because the metal is solidified without contact with a mold. Consequently the surface finish of the ingot is usually smooth and the ingot can be fed directly to rolling without machining, the surface (""scalping""). Scalping is necessary with alternative technologies (e.g., DC casting) where a mold is used. Consequently any disturbances that result in surface imperfections of EMC ingot are a serious matter. One type of imperfection is waviness on the surface of the ingot; a line drawn along the crest of a wave would run horizontally around the ingot. This imperfection may be caused by waves on the surface of the metal pool. As the waves reach the solidification line at the periphery of the metal they cause alternate outward and inward bowing of the meniscus at that point with attendant small (but significant) changes in ingot width. Elimination of building vibrations and similar disturbances minimize the occurrence of these surface waves but it is interesting to speculate whether there are disturbances of the metal pool that arise from the electromagnetic forces supporting the liquid metal. These forces are generated by the interaction of currents induced in the melt and the magnetic field produced by the current imposed on the inductor surrounding the melt. The present investigation has been concerned with whether the alternating magnetic field destabilizes the melt surface."

Jan 1, 1994

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By Alex Moyano

At present, the Codelco Norte smelter processes in the Teniente Converter and the Flash smelting Furnace 1,420,000 t/y of its Chuquicamata concentrate with an arsenic content of up to 1.5%. In a near future Codelco-Chile is considering different processing options for a new projected concentrates from the Alejandro Hales mine (former Mansa Mina mine with an arsenic content of up to 6%). The main option is the possibility to process 3,000 t/d of mixing concentrates from the Alejandro Hales and the Chuquicamata mines, in the Teniente Converter. The main feature of this smelting unit will be high volatilization of arsenic when processing high arsenic-bearing concentrates. The CN smelter staff carried out a technical feasibility study to evaluate the processing of high arsenic-bearing concentrates directly in the Teniente Converter, thus the low arsenic-bearing concentrates can be processed in the FSF. Accordingly, laboratory scale tests were carried out at the Tohoku University facilities. The lab-scale results allowed an industrial scale test at the Codelco Norte smelter to smelt 2,300 tpd of high arsenic-bearing concentrates in the TC and evaluate the metallurgical impact in the smelting, converting and refining areas of the smelter. The main industrial-scale result confirmed the stabilization of the arsenic content at 0.5% in the 70% Cu produced white metal at the test condition.

Jan 1, 2006

By P. Barrios

The copper refinery of Atlantic Copper was modernised and converted to the Isa permanent cathode system in 1995. The technology installed has proved to be an excellent platform for the development of operational improvements. During the years it has been working, the progressive assimilation of the new technology has been achieved and the level of operator knowledge has allowed design production to be reached and surpassed by more than 10%. At the same time, modifications to the work programmes, using existing equipment, have permitted the incorporation of new cells and the achievement of annual production levels of 250,000 tonnes and a productivity of 0.43 t/man-hour.

Jan 1, 1999

By Scott W. Jorgensen

Hydrogen storage research has a long history, with a recent surge of new materials and new concepts. Important progress has occurred in the area of solid phase materials for storage, tank materials and engineering, and new types of materials. More importantly, an understanding of these materials is beginning to allow prediction of hydrides with improved properties. The performance of these new hydrogen storage systems begins to approach that of physical containment methods. The next step is to directly target performance that will permit commercialization.

Jan 1, 2006

By A. Dadgar

Extraction of gold and silver from two refractory concentrates using cyanide and bromine reagents was reported at the 12th International Precious Metal Conference (1). The objective of this paper is to present the gold extraction, recovery, and economics for two refractory concentrates using cyanide and bromine reagents. Gold extractions for cyanide leaching (24- 48 hours) and bromine leaching (6 hours) were the same and ranged from 94% to 96%. Gold recoveries from bromine pregnant solutions using carbon adsorption, ion exchange, solvent extraction, and zinc and aluminum precipitation methods, were better than 99.9%. A preliminary economic analysis indicates that chemical costs? for cyanidation and bromine process are $9.50 and $10.50, respectively per ton of calcine processed.

Jan 1, 1989

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By A. Siegmund, Gerhard Martin

The recycling of metal containing scrap is a common practice in the industry and has a long tradition. . In rec~nt years, this philosophy has been transferred to organic materials, in particular to thermoplastic polymers. BSB . Recycling GmbH, a company with a long experience in the treatment and recovery of lead from battery scrap,· had recognized this exploitation at an early stage and challenged it by a consequent continuation of the idea to recycle materials other than metals without degradation and maintaining the quality. These efforts resulted in an economic and environmentally acceptable solution producing high quality polypropylene compounds at BSB beside lead and lead alloys from battery scrap. The raw material fair the production of polypropylene compounds is shredded plastics from the separated casings of spent lead-acid batteries. The production of polypropylene with specific physical and mechanical properties is carried out by the accurate dosing of organic as well as inorganic additives. The result of the procedure is a novel product group "Seculene PP", a registered trademark of BSB Recycling GrnbH.

Jan 1, 2000

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were carefully examined during the entire growth stage of bacteria (fermentation). Several very important discoveries were made. For example, the pyrite surface invariably drastically changed its properties at the second day of fermentation. Beyond two days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became insensitive to convective diffusion in solution (stirring).

Jan 1, 1990