Search Documents

By Soobhankar Pati

Solid oxide membrane (SOM) technology has been successfully employed for the production of high energy metals such magnesium, titanium and tantalum by directly reducing their oxides. This paper reports on the recent investigation done for calcium production by SOM process from calcium oxide, dissolved in fluoride and chloride based fluxes. This process employs an inert oxygen-ion-conducting stabilized zirconia membrane to separate the inert cathode in the flux from the anode. When the applied electrical potential between the electrodes exceeds the dissociation potential of calcium oxide, oxygen ions are driven out of the melt and through the zirconia membrane to the anode where they are oxidized. Reduced calcium metal deposits or evolves at the cathode depending on the operating temperature. The SOM cell has been electrochemically characterized, and key concepts related to CaO dissociation, leakage current, solubility of Ca in the flux, and hygroscopic nature of the flux relevant to the SOM process are explained.

Jan 1, 2008

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By Noritaka Horii, Katsuyoshi Kakinuma, Hiroshi Yamamura

"ZrO2 and Y2O 3-doped ZrO2 gel film were obtained by spin coating of sol from Zr-n-propoxide, n-propanol, acetylacetone, nitric acid, and water on a silica glass as a substrate. ·Dried gel films crystallized to monoclinic, tetragonal, cubic and their mixed phases, depending on the chemical composition of sol, .firing temperature, and coating cycles. ZrO2 films with highly preferential orientation were successfully obtained from a solution containing a large amount of n-propanol. The highly oriented ZrO2 film was found to have high transparency compared with non-oriented 'films. Electrical conductivity of 8 mol% Y2O 3 doped ZrO2 film was also measured.Introduction3 mol% Y2O 3 doped ZrO2, which has a tetragonal symmetry is ·well known to have a strong mechanical property and a high toughness. (1) On the other hand, 8 mol % Y 2O 3-doped ZrO2 is high oxide-ion conducting material and is applied to oxygen sensor, oxygen pump, and solid oxide fuel cell (SOFC). (2) Sol-gel methods using metallic alkoxide are widely applied for synthesizing ceramics such as high-purity fine particles, thin film, and fiber. (3) For ceramics films, many reports have been made on SiO2, (4) TiO2, (5) and PZT. (6) Several case studies have been done on zirconia film based on the sol-gel method, (7) - (11) but very few on preferentially oriented film and on systematic Y zO3 doping. Almost zirconia ceramic· films reported were prepared by means of dip-coating. Kamiya et al. (12) and Ganguli et al (13) converted zirconia into fiber. Sol from Zr alkoxide is usually very unstable, and a stabilizing agent such as glycol or ß-keton is used beforehand (7) (14)."

Jan 1, 2000

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By Pengfu Tan

A thermo-chemical model of the copper P-S converter and a viscosity model for the converter slag have been developed to predict the behavior of magnetite in the converter slag, amounts of slag and matte, compositions of slag and matte, volume of the bath, bath temperature, slag blow endpoint determination, SEMTECH OPC signals, and the viscosity of converter slags. The predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on Fe3O4 content in converter slag, slag viscosity, liquidus temperature of converter slag and skimming operation has been modeled and discussed as well. Some applications of the industrial operations have been presented.

Jan 1, 2009

By Yutaka Yasuda

The particle dispersion phenomena in a turbulent gas jet of the flash smelting process has been investigated. The particle number density in a non- reacting jet was measured experimentally by taking photographs of the particles in flight and counting them using the image analysis. Numerical computations were also performed using a mathematical model for a turbulent particle laden gas jet The experimental particle number density data were then compared with the predicted results of the model. Good agreement was obtained between the experimental and predicted data. The effects of the parameters such as the injector design, particle loading and air flow rate are discussed. Optimization of the concentrate burner design can be achieved with the help of experimental and theoretical simulation as performed in this work.

Jan 1, 1994

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By Alexandre Monteiro

Alumina precursor powders can be precipitated from aqueous solutions, using hydrothermal decomposition of urea to deliver base homogeneously to the system. Primary particles agglomerate early in the process, generating a wide size distribution. The presence of a polymeric surfactant such as polyacrylate can suppress or delay agglomeration, reducing particle size and narrowing the size distribution. The stabilization of commercially available a-Alp03 powder with polyacrylate was studied, investigating the effects of polyacrylate molecular weight, ionic strength and temperature. The effect of aluminum concentration, polyacrylate molecular weight and urea concentration on the precipitation of alumina precursors in a sulfate- urea system in the presence of polyacrylate/polyacrylic acid was then studied. The hydrolysis kinetics were followed, and particle sizes were determined. Precipitates were further characterized using energy dispersive spectroscopy. The particle characteristics are discussed in terms of the process conditions.

Jan 1, 1994

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By Rolando Campos

In August 1993, the operation of Refimet Chile's copper custom smelter commenced at La Negra, near Antofagasta in northern Chile. Design smelter throughput corresponded to 235 000 tonnes of concentrate, calcines and copper cements arising from suppliers in the north of the country to produce 90 000 t/y of blister copper. Refimet had initially gained experienced in building and operating leaching, roasting and a blast furnace facility at Rungue, near Santiago, followed by Roasting at La Negra. The initial smelter project was based on conventional reverb- smelting and Peirce-Smith converting and the majority of equipment was 'purchased second-hand and rehabilitated or modified. After only 3 years in production, the treatment capacity was significantly improved by introduction of technical improvements to the original plant operating scheme. Recently, the plant was further expanded to an annual smelting capacity in excess of 400 000 t/y feed, corresponding to around 160 000 t/y copper production. This expansion, referred to as Phase 2, was achieved by modification of the reverb to oxy-fuel firing, addition of a further (second-hand) acid plant, fire refining and anode casting facilities. Parallel development of concentrate injection into enlarged converters-also took place. Following successful commissioning of Phase 2 expansion, initial engineering studies for a third expansion phase have been completed. This aims to use leading technology based on bath smelting of bone-dry concentrates in a Continuous Reactor. This paper provides an overview of the relatively short plant history, its development and improvements together with operating indices achieved.

Jan 1, 1998

By Junji Shibata

The waste acid mixture whose main component is phosphoric acid, is discharged from the etching process in the liquid crystal production industry. In order to separate impurity acids from the phosphoric acid, trioctyl phosphate (TOP) is used as an extractant. TOP can extract acetic and nitric acids selectivity. The extraction and stripping operations are carried out for the acid mixture by beaker-scale experiments and countercurrent multistage operations with mixer-settler equipment. TOP selectively extracts the acetic and nitric acids in the acid mixture. From the results of the McCabe-Thiele analysis obtained by beaker-scale tests, the extraction for acetic and nitric acids are approximately 100%, respectively, by 6-stage extraction with a phase ratio (A/O) of 0.4. On the other hand, almost all of acetic and nitric acids are stripped with water from the organic phase by 4-stage stripping with a phase ratio (A/O) of 1.0. About 95% of acetic and 98% of nitric acids can be removed from the acid mixture without extracting phosphoric acid in case of the mixer-settler equipment operation. There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove any damaged layer caused in the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. The waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP (Tri-butyl phosphate). Finally hydrofluoric acid is separated with TBP solvent extraction. The expected recovered acids in this process are 2mol/L acetic acid, 6mol/L nitric acid and 6mol/L hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes from a viewpoint of environmental preservation. Most industrial products are made through processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane separation, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

Jan 1, 2003