Search Documents

By B. C. Blakey

The economic feasibility of the sulphuric acid pressure leaching route for the extraction of nickel and cobalt values from limonitic ores is highly dependent upon the behavior of aqueous aluminium. This is primarily due to its precipitation as hydronium alunite ((H30)A13(S04)2(OH)6), which is one of the major scale-forming compounds found in autoclaves used for pressure leaching. As a result of renewed interest in the pressure leaching process, an investigation of the aqueous-solid eqilibria in the aluminium-sulphate-water system under acidic (< pH l), high temperature (230 to 270°C) conditions has been conducted. Pure hydronium alunite was synthesized in an autoclave by leaching boehmite (A100H) at elevated temperatures in sulphuric acid solutions initially 0.25 to 0.75 m H2S04 in concentration. Spontaneous, in situ precipitation of hydronium alunite followed. A high temperature solution speciation model was used for the analysis of the resulting solubility data in order to calculate equilibrium constants for the precipitation reaction.

Jan 1, 1994

By Gary Kordosky

Equilibrium modifiers, first introduced into copper solvent extraction reagents in the late 1960?s, are widely used. The properties of various equilibrium modifiers with respect to copper extraction, selectivity, reagent stability and entrainment are discussed and some conclusions are drawn relating the structure of the modifier to the properties of the modifier. A new highly selective, low viscosity modifier is also introduced.

Jan 1, 2003

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By George R. St. Pierre

A method for the quantitative description of activity interactions between solutes in a metallic solvent which is consistent with stalistical thermodynamic principles is presented. The chemical potential of a solute in an alloy is derived from the weighted mean of its values in the individual solvent components, µi = S?jµi(i). The weighting factors, ?j, are obtained from the distribution functions. The resulting equation contains far fewer adjustable parameters than the Epsilon Formalism and because of its correct functional form it provides an improved fit to the available data on a variety of alloy systems containing oxygen, carbon, sulfur, nitrogen, and hydrogen. For a binary metallic solvent ( A, B ) containing a solute (i), it is shown that

Jan 1, 1995

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By M. Tangstad, H. Mølnäs, J. D. Steenkamp

"Temperature affects several aspects of pyrometallurgical systems, including thermodynamics and reaction kinetics. Reliability of temperature measurements in laboratory and plant applications is thus important from process, safety and financial perspectives. This case study briefly introduces different techniques utilized for temperature validation, and demonstrates temperature validation on laboratory scale utilizing the wire-bridge method. Pt/Ptl3Rh thermocouple hot junctions were constructed by mechanically connecting thermocouple wires through a pure metal bridge consisting of copper, gold, nickel or palladium wire. When heating the wire-bridge thermocouple alongside a regular Pt/Ptl3Rh thermocouple, temperature offsets were quantified as the wirebridge thermocouple short-circuited at the melting points of the pure metals. At the melting points of gold (1064°C) and palladium (1555°C), average measured temperature offsets were -2.1°C ± 2.3°C and 0.2°C ± 0.4°C, respectively. Results from the copper and nickel wire-bridges were inconclusive. The paper concludes with a discussion on the potential industrial applications of the technique.IntroductionThermocouples are probably the simplest of all temperature sensors, but are widely utilized due to simplicity, versatility and ability to handle a variety of experimental conditions and industrial applications. Additionally, thermocouples are often the only option in research laboratories requiring high temperature measurements, and a high level of reliability is usually required from thermodynamic, kinetic as well as safety points of view.The study presented here originated from a test program where the compatibility between different types of carbon-based refractory materials and industrial slag produced in silicomanganese furnaces were investigated on a laboratory scale utilizing the static crucible test[l]. Due to the nature of the silicomanganese production process, the compatibility tests were to be conducted at 1600CC[2]. Details of the experimental set-up utilized for the compatibility tests are discussed in the Experimental Set-up and Method Statement section later in this paper."

Jan 1, 2012

By K. A. Lewandowski

Agglomeration of ore can be used to immobilize fine particles during heap leaching by agglomerating them into granules. Without agglomeration, the fine ore particles can migrate within the heap, clogging flow channels and producing large areas where access of solution to the ore is very poor. The benefits of agglomeration are well-known in gold heap leaching operations, which can be effectively agglomerated using binders such as Portland cement due to the alkaline leaching solutions used. However, agglomeration has not been very effective in the heap leaching of copper ores, because these ores require an acidic leaching solution. Acid destroys the effectiveness of most binders, causing the agglomerates to disintegrate as soon as the leaching solution is applied. In order to gain the benefits of agglomeration in copper heap leaching, an economical, acid-resistant binder is needed. The two issues that needed to be addressed were: 1) Lack of effective methods for evaluating binder acid resistance before performing expensive, time-consuming, full-scale heap leaching tests, and 2) The vast majority of known binders react poorly to acid conditions, and so a basis was needed for determining which binders are most likely to be acid-resistant. In this paper, the development of two new tests for evaluating binder acid resistance in the laboratory are described. The ?soak test? determines the degree to which agglomerates disintegrate and release fines on contact with acidic solution, measuring the relative quantities of fines released by agglomerates made with different binders under controlled conditions, and serves as a rapid means for comparing large numbers of binders. The ?percolation test? measures several different parameters to determine how a binder is likely to perform in heap leaching: 1) the degree of ?slump? and compaction of agglomerates as they are wetted by acidic solutions; 2) the hydraulic conductivity of the agglomerate bed; 3) the migration of fines through the bed as the solution flows through it; and 4) the quantity of liquid retained in the agglomerates after they are drained. Using these tests, a broad spectrum of binders were examined. Soak testing determined that the most acid-resistant binders were nonionic polymers. Five of these binders were further evaluated using percolation testing.

Jan 1, 2006

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By De-qing Geng, Guang-liang Wu

The waste slag generated by the LF refining process of Q345B low alloy hot-rolled steel, still has some refining capabilities. If recycled, it can reduce environmental pollution, and save the economic costs. A research on melting Characteristics of Q345B steel LF refining waste slag was investigated by using orthogonal experimental method, and the effect laws of composition on that were analyzed. Through variance analysis and significance criterion, it is concluded that the optimum ingredient of the regenerated LF refining slag is 25%A12O3, 12%CaF2, 7%MgO and R= (CaO)/ (SiO2) =2.5. And the regression analysis is carried out by using SPSS software, to get the mathematical relationship between ingredient with high reliability and melting temperature of refining slag T=1451.3-6.25CaF2+2.36 R.

Jan 1, 2016

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO&apos;TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By V. Jiricny

The novel spouted-bed electrode (SBE) is a cathode system where copper is deposited at a high current density in a moving bed of copper particles. Preliminary results on the deposition of copper from acidic sulfate electrolytes using this novel cathode system were described during Copper &apos;95 conference. Despite a high current density, the electrical energy consumption was equal to or lower than that in the conventional electrowinning. The present paper describes more investigations on SBE. The SBE consists of copper particles with approximately 1 mm diameter onto which copper is deposited from acidic sulfate electrolyte whose composition is similar to conventional electrowinning. Three types of anodes were used in conjunction with the spouted-bed cathode, namely, DSA anode for oxygen evolution, and two novel anodes. One anode is less expensive than DSA; however it showed much promise in energy consumption. At a superficial current density of 2200 A/m2, the energy consumption was around 1.0 kWh/kg copper. The research activities described in this paper were supported by BHP Copper.

Jan 1, 1999

By Roberto Parra, Roberto Parada

"A novel process for minor elements control in copper pyrometallurgical production is proposed based on a theoretical analysis and the results of an experimental program. Its application can solves operational problems related to volatile elements that determine pollutants gas emissions and the final quality of anodes. The process considers a calcination of mixtures of the dust with sulfidizing agents such as dirty copper concentrate or elemental sulfur at temperature under 800 °C. The product are a clean calcine that recovers all the Cu content on the dust and a gas stream that collect the minor elements as sulfides species. The calcine can be returned to the smelter avoiding the As increasing in the circuit and so on, the capacity for the treatment of dirty concentrates for the smelter can be higher. The possibility to apply vacuum in the calcinations step can decrease the operation temperature. The solid condensed from the gas has different options for its stabilization, with the advantage that this stream represents few mass with high As content.IntroductionThe control of undesired minor elements (IVIES) in conventional pyrometallurgical copper production is especially relevant for ore deposits associated to Andes region. The concentrates that are being produced present every time higher levels of volatiles and harmful elements: group Va (As, Sb and Bi), Pb, Zn, and Sn."

Jan 1, 2008

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013

By Pedro Morales C.

From its beginning in the 1970s, the Teniente Converter has consistently achieved continuous improvement, and has contributed to the competitiveness and sustainability of Codelco&apos;s copper operations. The later introduction of the Slag Cleaning Furnace technology has helped to create a full technology package, referred to as the Teniente Technology. This paper outlines the features of a new research and innovation program designed to bring the Teniente Technology as a modem, competitive technology into the 21st century. The overall objectives and features of the program are described and discussed. It is fully anticipated that these activities will help position the Teniente Technology as a world-class modem technology, well-integrated and operating in a fully continuous mode in conjunction with the other units at the plant, a competitive technology which operates in harmony with respect to environmental regulations.

Jan 1, 1999

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Ulrich E. Klotz, Gemot Pottlacher, Shahid Mehmood

"Platinum alloys are frequently used in technical applications and in jewellery. Their thermophysical properties such as density, heat capacity, thermal conductivity and surface tension play an important role in casting processes and are required as input data for casting simulation. Scope of this work was to investigate these properties by different methods. Platinum and four alloys namely, Pt96Cu4, Pt68Cu32, Pt50Cu50 and Pt25Cu75 were investigated. Melting range and thermal expansion was measured at fem by DSC and dilatometry, respectively.At TU Graz wire shaped samples were investigated by an ohmic pulse heating technique. This technique allows the calculation of specific heat capacity and the temperature dependencies of electrical resistivity, enthalpy, and density of these alloys in the solid and liquid phase. Experimental results were compared with available literature and data from thermodynamic calculation using the SNOBl database and ThermoCalc.IntroductionPlatinum is a precious element and its alloys are commonly used in jewellery. But Platinum is much more difficult to cast then other jewellery elements like silver or gold, because of its high melting temperature, large shrinkage during freezing, low thermal conductivity, high surface tension, and high viscosity. As a result there arise problems during casting. Hence to resolve these difficulties a detailed study of thermophysical properties of solid and liquid platinum and its alloys is necessary for simulation and casting. The Platinum alloy samples were prepared by vacuum induction melting and casting into copper molds. Rods of 3 mm in diameter and a length of 80 mm were prepared and drawn to wires of 0.5 mm in diameter."

Jan 1, 2011