Search Documents

By Li Rongxing

A general regular solution model put forward in this paper defines a general interaction parameter that includes both composition and temperature dependence. On the basis of this model, analytic express of solution excess properties was obtained by least square fit using the composition and temperature relations in binary alloy phase diagram. After some solution excess properties analytic expresses of correlated binary alloy system obtained, the analytic express of ternary alloy system could be obtained by superposition of general geometrical model. The ternary alloy system Pb-Sn-Zn has been predicted in terms of this method and the result was very in agreement with actual measured value.

Jan 1, 2006

By Christopher Solnordal

A mathematical model was developed to simulate the performance of the reaction shaft at BHP-Billiton?s Olympic Dam copper flash smelter. In order to have confidence in the predictions of the mathematical model, validation was performed by comparing and reconciling the predictions from the model with the results from a campaign of sampling and plant measurements. The model was based on the computational code CFX4.4 utilizing a combustion sub-model purpose-built by CSIRO. The combustion sub-model employed the concept of a composite particle which contained the three components of the solid charge: concentrate, flux and returned dust. Plant measurements were made and samples taken immediately below the burner and through a port halfway down the reaction shaft. Parameters measured included temperature, solid loading and SO2 concentration in the gas. Comparison of the measured and predicted values then showed that: predicted far field gas temperatures were within ±50C of measured values; predicted temperatures in the central plume were lower than measured, and, the predicted plume width was slightly smaller than measured. An optimum composite particle size of 19 m was identified for use in future modeling work at Olympic Dam.

Jan 1, 2006

By Philip L. Sibrell

A new process utilizing pulsed fluidized limestone beds was tested for the remediation of acid mine drainage at the Friendship Hill National Historic Site, in southwestern Pennsylvania. A 230 liter-per-minute treatment system was constructed and operated over a fourteen-month period from June 2000 through September 2001. Over this period of time, 50,000 metric tons of limestone were used to treat 50 million liters of water. The influent water pH was 2.5 and acidity was 1000 mg/L as CaCO3. Despite the high potential for armoring at the site, effluent pH during normal plant operation ranged from 5.7 to 7.8 and averaged 6.8. As a result of the high influent acidity, sufficient CO2 was generated and recycled to provide a net alkaline discharge with about 50 mg/L as CaCO3 alkalinity. Additions of commercial CO2 increased effluent alkalinity to as high as 300 mg/L, and could be a useful process management tool for transient high flows or acidities. Metal removal rates were 95% for aluminum (60 mg/L in influent), 50 to 90% for iron (Fe), depending on the ratio of ferrous to ferric iron, which varied seasonally (200 mg/L in influent), and <10% of manganese (Mn) (10 mg/L in influent). Ferrous iron and Mn removal was incomplete because of the high pH required for precipitation of these species. Iron removal could be improved by increased aeration following neutralization, and Mn removal could be effected by a post treatment passive settling/oxidation pond. Metal hydroxide sludges were settled in settling tanks, and then hauled from the site for aesthetic purposes. Over 450 metric tons of sludge were removed from the water over the life of the project. The dried sludge was tested by the Toxicity Characteristics Leaching Protocol (TCLP) and was found to be non-hazardous. Treatment costs were $43,000 per year and $1.08 per m3, but could be decreased to $22,000 and $0.51 per m3 by decreasing labor use and by on-site sludge handling. These results confirm the utility of the new process in treatment of acid impaired waters that were previously not amenable to low cost limestone treatment.

Jan 1, 2003

By Manuel Pérez-Tello

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. Oxygen concentration in the process gas was set to 40 and 70% by vol. and a heating rate of 40 °C/min was used. Response variables included: the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology, and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles, and by thermochemical and mass balance calculations to reproduce the DSC and TGA thermograms. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction for each mineral as a function of time. Experiments conducted with copper concentrate particles containing the minerals studied suggest that the reaction mechanisms for the individual minerals can be used to represent the oxidation behavior of the copper concentrate particles.

Jan 1, 2006

By Zhouhua Jinag

The attempt has been made to manufacture high nitrogen austenitic stainless steels by pressurized electro-slag remelting furnace with maximum nitrogen pressure of 7MPa. To obtain high nitrogen content in steels, the compound electrodes with different nitrogen sources (FeCrN, Si3N4) were prepared. Using the Si3N4 as the nitrogen alloying source, the silicon contents in ingots were prone to be out of the specification range, and the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved using FeCrN as nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen above 1.0wt% could be obtained. A series of high nitrogen austenitic stainless steels have been successfully developed by this method. The mechanical and pitting corrosion resistance properties of high nitrogen austenitic stainless steels were investigated. The results show that the steels exhibit excellent mechanical and pitting corrosion resistance properties.

Jan 1, 2009

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

By P. A. Olubambi

The effect of ore mineralogy on the bioleaching of metals from complex sulphides was studied by investigating the bioleaching of zinc and copper from a bulk complex sulphide ore from Ishiagu, Nigeria, using mixed cultures of Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Leptospirillum in mechanically stirred reactors at varying particle sizes. Mineral phases within the varied particle sizes of -53, 53, 75 and 106µm were identified using X-Ray Diffraction (XRD), while the elemental distribution within the varied particles sizes was determined by X-Ray Fluorescence (XRF) and Optical Emission Spectrometry using Inductively Coupled Plasma- Optical Emission Spectrometer (ICP-OES). Bulk ore and the leached residues were examined by X-Ray Diffraction. The highest bioleaching recoveries were obtained at particle size of 75µm, while particle size of 106µm gave the least recoveries. Lower recoveries at particle sizes of 53 and -53µm were as a result of their higher silica and siderite content which affects pH, iron mobility and oxidation.

Jan 1, 2006

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999

By R. W. Hammack

Results for the treatment of a problematic mining wastewater using bacterial sulfate reduction (BSR) are presented. Specifically, a BSR pilot treatment plant (250 L per day) was used to treat Berkeley Pit simulant to discharge standards with the selective recovery of separate Cu- and Zn-sulfide concentrates. Concentrates recovered in these tests contained greater than 50 % of the target metal and met specifications for sale to existing smelters. The biological component of the treatment was found to be surprisingly robust. Scaling and solid/liquid separation problems were encountered but considered normal for sulfide treatment. For Berkeley Pit water, capital costs for BSR treatment was found to be comparable to high-density sludge lime treatment. The value received from the sale of recovered copper ands zinc concentrates paid for all the operating costs.

Jan 1, 1999

By C. O. Bounds

The performance of AB5-type alloys for hydrogen absorption including the electrochemical absorption as an electrode for rechargeable batteries has been demonstrated&apos; to be a complex function of the composition, microstructure and surface condition. The compositional studies have focused primarily on substitutions for Ni on the B-site (e.g. Co, Al, Mn, etc.). This current study examines the effect of rare earth substitutions for La on the A-site and considers both other "light" rare earths (Ce, Nd, Pr) and "heavy" rare earths (Dy, Sm, etc.).

Jan 1, 1997

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By Mari Naess, Jan Erik Olsen, Gabriella Tranell

"Fume, also known as dust, is produced during metal refining. Exposure to fume is damaging to the health of plant operators. A mathematical model has been developed to study the different factors governing the fuming mechanism. It is shown that natural convection is the main driving force of the phenomenon, and that the fuming rate is highly sensitive to the area of the exposed metal surface. A new feature introduced in the modeling concept is the ability to include a gas flux of unconsumed process gas flowing up through the metal surface. This reduces the fuming rate, and should normally not be neglected.IntroductionFormation of fume from the ladle in which metal is refined into its final specifications is an environmental issue of importance for the working environment in the production plant. In layman-term fume is often known as dust. It is formed when metal reacts with oxygen. As an example of a fuming process, we will focus on ladle refining of silicon. Note that many of the principles and conclusions will apply to other metal refining processes. For silicon production, silica fume (S1O2) is produced when silicon metal (Si) reacts with oxygen (O2).Silicon is produced in a submerged arc furnace. The metal is tapped from the furnace into a ladle for refining. The refining is conducted by injecting a mixture of air and pure oxygen at the bottom of the ladle. The oxygen reacts with the metal and the impurities, and the amount of impurities is reduced according to product specification. At the ladle surface, metal also reacts with oxygen present in the air surrounding the ladle. This reaction produces silica fume as illustrated in Figure 1."

Jan 1, 2012

By Henk Dijkman

Existing metallurgical operations can be optimized by implementing engineered bioreactor systems in the process configuration. For instance, metals can be recovered safely and economically from process and waste streams using biogenic sulfide. This paper focuses upon possible applications of high rate biotechnology in metallurgy and mining. Metal recovery from liquid streams (process bleed streams, leach water, waste streams), integrated removal of (fugitive) SO2, treatment of acid blowdown and other options will be described. Practical examples are given. A large-scale application of biotechnology at Pasminco&apos;s Budel Zink refinery is described. Here, acid plant blowdown is treated together with electrolyte magnesium bleed. Concentrated zinc sulfide (10 tpd) is produced biologically, eliminating the production of gypsum and closing the refinery sulfur cycle. Recovery of metals from solution at Kovehute Pribram in the Czech Republic is the second practical example. In this case, H2S is produced on-site for metal removal from an alkaline slag dump leachate. At the Caribou mine in New Brunswick, Canada, acid mine drainage is treated with biogenic sulfide. This plant is situated upstream of a lime neutralization plant. As a result, reusable ZnS is produced, the volume of the sludge (gypsum and hydroxides) from the lime plant is reduced by 50%, the sludge is free of heavy metals and the final effluent concentration of heavy metals is in the ppb range. In the second phase of this project, metals will be recovered from stored tailings, resulting in significant revenues.

Jan 1, 2002

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By Qingbo Yu, Qin Qin, Junxiang Liu

"Dry-granulation is a new process of molten blast furnace slag treatment and air is used as heat exchange medium. There are some shortages: poor effectiveness of granulation, high air-slag ratio and high energy consumption, which are the obstacles to popularize dry-granulation. Based on rotary cup atomization, the technique of recovering waste heat of molten blast furnace slag through waste heat boiler producing high pressure steam is exploited. The molten blast furnace slag is granulated to uniform small slag granules with high temperature, and slag granules pour into the waste heat boiler. It could produce steam, obtained in first row and second row tubes, when descending velocity of slag granules equaled 1.1mm/s and the Reynolds number equaled 7100. The application of the system for recovering waste heat from high temperature molten blast furnace slag has a significant meaning.IntroductionBlast furnace slag is one kind of solid waste in iron making process, which is discharged at the temperature range from 1723 to 1923K. In China, there was 0.162 billion tons of slag discharged in 2009, and the energy contained in the slag is equivalent to the energy in 9.4 million tons of coal equivalent. The sensible heat of molten slag is a very valuable waste heat source, so it is worthwhile to recover the sensible heat. At present, the molten slag is treated by a water quenching method. But in this process, the sensible heat is not recovered, moreover, an amount of water is consumed and harmful waste gas is discharged into the environment. Due to the considerations of energy conversation and environmental protection, the iron making industry pays close attention to dry-granulation, which is useful to obtain more benefits [1-4]. The sensible heat is recovered and an amount of water is saved by the method of dry-granulation. The amorphous content of slag granules obtained from dry-granulation is over 95% [5, 6], so the slag granules can be used as a perfect raw material for cement [7, 8].In the late 1970s, the Sumitomo Metal Industries, Ltd. and the Ishikawajima-Harima Heavy Industries, Ltd. jointly undertook the research of rotary drum granulation. This method has several disadvantages: the processing capacity and efficiency are low, and it is not adoptive to operate continuously in production [9]. From 1980, Nippon Steel, NKK, Kawasaki Steel, Kobe Steel, Sumitomo Metal Industries and Nisshin Steel were engaged on air granulation, and the experiments were operated for 6 years on the blast furnace in Nippon Steel. In the process of air granulation, there was great power consumption. The complexity of structure and the great floor space of the air granulation device caused high cost of investment. In 1986, Ukraine exploited a new method of heat recovery referring to the technology of Continuous Casting and Rolling [10]."

Jan 1, 2011

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By Roald Ysteboe, Finn Olesen

"Elkem has developed a process that utilizes SPL as a raw material for pig iron production. This process will be demonstrated in industrial scale during 2008 and 2009. The process developed produce iron, and the reduction material used, is the carbon present in the SPL. The iron source could be either virgin iron ore or waste/recycled material from the steel industry. The SPLrefractory and bath material is dissolved in the slag produced. The slag is designed so that any leaching of environmentally dangerous elements is minimized. This process can in addition to SPL, consume other types of waste derived from the primary production of aluminium. Elkem intends to supply this demo project with SPL and other waste products from external sources, domestic as well as international ones.IntroductionSpent Pot Lining (SPL) is generated when an electrolytic cell for producing aluminium is taken out of service and the refractory and carbon lining is removed from the steel potshell.The yearly generation of SPL world wide is exceeding 500 000 tonnes. The major amount of this quantity is stockpiled or land filled, unprocessed.SPL contain large amount of water soluble fluorides and some amount of cyanides and is classified as hazardous waste in most countries."

Jan 1, 2008

By Roberto Giovanardi, Isabella Lancellotti, Luisa Barbieri, Ercole Soragni, Fernanda Andreola

"Recovery of precious metals (PMs) is a present topic, as they are used almost in every electronicelectric device. Gold is the second PM in order of consumption (following silver) and it is almost ubiquitary in electronics where it mainly finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. Given this, discontinued electronic and, with a minor role, electric devices may represent a primary source of PMs as gold mines or jewelery wastes.At present the recovery of gold from such waste is generally accomplished by two strategies: by oxidative thermal treatment followed by metallurgical or chemical processes or by cyanide chemical etching; both techniques do not represent the optimum as the first one deserves a great amount of energy and non-combustible pollutant slag and fumes are produced, while the second procedure comports the use of a highly pollutant agent as cyanide.The aim of this work is the characterization of different electronics scraps to evaluate the gold concentration, and the selective recovery of this metal using enviromentally-friendly techniques. In particular, a new process was developed in order to overcome such environmental and efficiency issues. The process reaches the goal of detach the gold film from the substrate by selective leaching of the supporting metal.IntroductionThe treatment of waste from electrical and electronic equipments is a current topic as their role in modern life is increasing. The disposal of such waste represents both an environmental and an economical concern due to the vast amount of both precious and non precious metals.The use of precious metals (PM) in this field is of primary importance given PM’s unique properties, which give to each of them a specific and irreplaceable role. Silver is the most used, with a demand of over 5000 tonnes per year, mainly for switches and contacts in electric appliances. Gold is the second PM in order of consumption (over 250 tonnes per year and 8% of the total demand) and it is almost ubiquitous in electronics where it finds application to produce bonding wires in integrated circuits and as a coating for contacts and connectors. It is also used as solder in integrated circuits (in alloy with tin) or for wide coatings where it ensures protection against corrosion. Palladium, platinum, rhodium and iridium follow in order of consumption [1- 3]."

Jan 1, 2008