Search Documents

By M. Pineau, G. A. Monteith, M. Laliberte, G. Houlachi

Conventional physico-chemical treatment methods, either hydroxide or sulfide precipitation, can hardly achieve a high removal of selenium from the liquid effluents which can be generated in some metallurgical operations. In weak acid solutions, selenium exists mainly as anionic species (selenite Se03-2 and selenate SeCV2) which, therefore, cannot precipitate as metal hydroxide or metal sulfide compounds. At the same time, neither selenite nor selenate form stable precipitates with the common cations (Ca, Mg, Fe, etc.) that are typically used in water treatment. At Noranda Inc., CEZinc Division in Valleyfield, Canada, the introduction of new discharge requirements for effluent toxicity initiated a R&D program which resulted in the full-scale implementation of a new treatment method for selenium removal. The goal of this paper is to present this new method which is now being patented by CEZinc. The process chemistry will be presented along with pilot-scale developments and full-scale operational results.

Jan 1, 2000

By Guy Deschênes

Thiourea solutions can be used as leach liquors to treat gold ores or slimes. It is also efficient to elute resins or strip solvents that were loaded in cyanides solutions. The hydrogen pressure reduction is a practical step to recover gold and silver from leach solutions, and strips and eluates without any destruction of thiourea. It is a critical point because these processes have to consider the recycling of the liquors to be irore economical. The effect of temperature, pressure, acidity, compotation of the solution and the nature of catalysts on pressure reduction by hydrogen were investigated. An electranetallurgical study was? carried out to investigate the mechanism. The composition of the products was studied by different analytical methods. The process shows a good selectivity to precipitate gold and silver in a thiourea solution containing iron and copper. Gold and silver concentrations can be decreased to 0.2 ppm and 0.1 ppm at respectively 70 KPa H2 and 28°C. No decomposition of thiourea was evident during the tests. Metals such as nickel powder or platinum activate the reaction and improve the reduction.

Jan 1, 1989

By Upali Siriwardane, Tushar V. Kudale, Naidu V. Seetala

"Cellulose acetate (CA) membranes with 25% triethyl citrate (TEC) as plasticizer were prepared with varying thickness for CO2 gas separation from water-gas-shift (WGS) reaction products. The AFM analysis of the CA membrane showed that the uniform coating had fewer and smaller pores as the film thickness increased, and corroborated by gas permeability studies. The CO2 permeability has decreased faster than CO permeability with the CA/TEC membrane thickness, and findings support that the CA membrane could be used to entrap CO2. Several CA/TEC membranes were also staked to increase the separation efficiency. Positron Annihilation Lifetime Spectroscopy (PALS) was used to estimate the nano-porosity (pore size and concentration) changes of CA/TEC films. PALS results show a decrease in pore size with increasing CA-TEC concentration in acetone, while the pore concentration increases. The PALS results are correlated with the CO2/CO permeability variations as the CA-TEC concentration change.IntroductionHydrogen is one of the main energy sources available for the future advancement of clean fuel technologies especially for fuel cells. Generation of hydrogen and CO2 from Water Gas Shift (WGS) reaction mixtures of CO and H2O is of interest to many researchers since it allows a large scale production of hydrogen [1, 2]. Once hydrogen is produced using the WGS reaction, the output products contain mixture of CO, CO2, H2, and water vapor. Metallic membranes have been used as hydrogen separation membranes [3-6]. As H2 is separated from the mixture using the metal membranes, we need to separate CO2, and find ways of sequestration of CO2 to avoid environmental problems by greenhouse gasses. Polymeric Membranes have been used for CO2 separation [7]. Plasticizer can control the micro-structural properties such as pore size and concentration of polymer membranes [8], which influence the size/molecular weight dependent diffusion rates of the gas molecules. We have used cellulose acetate with triethyl citrate as plasticizer to separate CO2 from the WGS reaction products. Positron annihilation lifetime spectroscopy (PALS) is very sensitive and able to identify different kinds of defects and their agglomerates such as vacancies, vacancy loops, and voids [9, 10]. PALS has been successful in determining the free volume in polymers that influence the properties of the polymers [11, 12]. Microscopic properties of the free volume obtained from PALS have been correlated to macroscopic properties [13, 14]. We used PALS to study the nanoporosity (pore size and concentration) and fractional free volume changes of CA/TEC films, and used to understand the variations observed in the CO2/CO permeability as the CA-TEC concentration in the membranes change."

Jan 1, 2014

By M. Cross

Heap leaching presents a complex physico-chemical process to model and a significant challenge to develop a comprehensive model enabling reliable predictions of heap behavior over the long term. A computational modeling framework is described for the analysis of multi-phase flows in reactive porous media suitable for tracking metals recovery, for example, in heap leaching and environmental recovery processes. This modeling framework employs appropriately formulated, parameterized, and solution procedures to capture: 1) liquid and gas flow through heterogeneous porous media subject to variably saturated flow conditions, 2) the complex and dynamically changing nature of the porous media structure, 3) the transport of reactants and products of reaction, 4) the simultaneous mass and heat transfer, and 5) the role of bacteria as a catalyst for reactions. A second class of challenges to accurately model heap processes is to identify and then capture all the process data to characterize the reactivity of particular ores, the mine planning for the construction of the heap, leach schedules, meteorological data, etc. The objective of this paper is to outline these challenges and to describe a modeling framework that can cope with arbitrarily complex geometries and provide tools for rapid and accurate process assessment.

Jan 1, 2006

By Ray Y. Lin, Sunil G. Warrier

"Low cost processing of metal matrix composites is an essential requirement for this class of materials to be acceptable in commercial application. In an effort to reduce the cost of processing of metal matrix composites, an infrared pressureless liquid infiltration technique has been developed. The salient features of infrared infiltration are that it is rapid, simple and a low cost process. The rapid processing capability causes very little oxide formation on the alloy resulting in both improved wetting and flow characteristics and reduced oxygen contamination in the composite. Thus, vacuum is normally not required. Using infrared inflltration, aluminum and titanium matrix composites have been prepared under an ambient argon atmosphere. Reinforcements in these composites include carbon fibers, silicon carbide Nicalon fibers and Textron's SCS fibers. Microstructural and mechanical test results indicate that completely consolidated composites with good fiber distribution, limited interfacial reaction and high mechanical properties can be manufactured by this process. IntroductionAluminum and titanium matrix composites reinforced with ceramic reinforcements are strong candidates for numerous applications in the aerospace and automotive industries. Aluminum matrix composites are commonly fabricated by either solid state vacuum hot pressing, liquid state pressure infiltration or squeeze casting [1]. Although liquid state pressure infiltration and squeeze casting has significant advantages over solid state processes, the requirement for pressure makes these composites uneconomical for large scale industrial application. Titanium matrix composites are primarily fabricated by solid state diffusion bonding [2]. Pressureless liquid infiltration can significantly reduce the cost of fabrication in both the composite systems. However, during pressureless infiltration processes, several complications concerning the wetting characteristics and chemical compatibility arise."

Jan 1, 1994

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By G. L. Pedroti

With the development of industrial processes and the consequent emergence of numerous products that quickly become necessities, industrial activity has acquired an essential character today. Although its importance is unquestionable, industrial activity is responsible for generating quite a large number of residues, with different shapes and characteristics. It has been observed, in particular the grits (Kraft process in the cellulose industry) and the residue from the processing of granite. And, given the importance of Portland cement as a building material, its vast employment and waste properties that resemble components of the clinker, it was decided to produce cementitious compounds from these industrial wastes. The residues were subjected to mineralogical, chemical, physical and morphological. And, the mixing ratio between the residues in the 70% and 30% grits residue granite was sintered at 1250 ° C furnaces to burn threshold of 6 hours forming new compounds observing tri-calcium aluminate and di-calcium silicate that are compounds found in portland cement.

Jan 1, 2015

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011

By C. Camurri

Results from the Metallurgical Department of Universidad de Conception showed that fire-refined copper could be rolled without previous remelting for deoxidation. The goal of this work is to determine the rheology of fire-refined copper from tensile tests at different temperatures and strain rates, and Ford plane compression tests. All that in order to simulate and calculate rolling process variables. For rheology hardness coefficients, n variables between 0.28 at 600°C and 0.46 at ambient temperature are obtained. The sensibility coefficient for strain rate m varies between 0.056 at 600°C and 0.006 at ambient temperature. The activation energy for plastic flow Q in the considered temperature range is 1436 cal/mol.

Jan 1, 1999

By Robert L. Opila

Negative electrodes for alkaline nickel-metal hydride batteries composed of MmNi3.5Al0.8Co0.7, where Mm is misch metal, have been characterized electrochermically and using x-ray photoelectron spectroscopy. The stability and rapid hydriding and dehydriding kinetics of the alloy in KOH are attibuted to a surface film. The protective surface film is shown to consist of an porous, outer hydrated layer and a dense, inner oxide layer. In addition, metallic nickel and cobalt are found throughout the film, and are presumed to form a conductive, percolative network that permits rapid electron transfer from the bulk to the solution, allowing rapid electrochemical formation of atomic hydrogen.

Jan 1, 1997

By B. J. Jody

Each year, about 11 million tons of metals (ferrous and nonferrous) are recovered in the U.S. from about 10 million discarded automobiles. The recovered metals account for about 75% of the total weight of the discarded vehicles. The balance of the material or shredder residue, which amounts to about 3 million tons annually, is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This paper discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two- stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology is discussed, and the process economics are reviewed.

Jan 1, 1994

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Zhendong Tao, Wei Huang, Zhongxi Yang, Hang Guo, Haoran Geng, Jingxiang Yao

"CaSO3.0.5H2O typed Flue Gas Desulfurization (FGD) gypsum is a by-product formed in flue gas desulfuration by double-cycle fluid bed method, its composition is different remarkably from that of gypsum yield by normal desulfuration methods, and few studies using it as cement retarder have been carried out. In this paper, the experimental study using CaSO3•0.5H2O typed FGD gypsum as cement retarder was carried out. The experimental results indicate that, when FGD gypsum is added solely into cement, the retarding action is not satisfactory because of its slow dissolution rate; The composite retarder composed of FGD gypsum and natural gypsum can regulate efficiently setting time of cement over a wide range of addition and rate of both each other, and the mechanical property of cement can be improved significantly.Fire-power plants have discharged a lot of harmful gases such as SO2 etc., which has resulted in serious pollution on the environment. To reduce harmful gas containing sulfur in the flue gas, various flue gas desulfuration (FGD) techniques have been developed. At present, the FGD method used widely is to add desulfuration agents such as limestone powder or other calcareous-contained materials during the coal burning or in the flue gas so that the components containing sulfur react with them to form solid sulfate or sulfite and to be separated from the flue gas by collectors. CaSO3•0.5H2O and CaSO4•2H2O typed FGDgypsum can be obtained respectively by dry and wet FGD process[1,2]. As a by-product of fire-power plant, features of of FGD gypsum and its applications have been paid great attention. Pavel Tesa'rek et al [3] presented in full the characters and properties of FGD gypsum; Zofia Konik et al[4] prepared expansive additive used to cemnent industry by using FGD gypsum and aluminate clinker; A. K. Alva et al [5] investigated the effects of FGD gypsum and fly ash on soil properties and found the growth of seedlings of either rootstock improved significantly in soils amended with FGD gypsum and fly ash. FGD gypsum also can be used in gypsum binders, plasters and plasterboard manufacture [2.6]. C. S. Poon et al [7] investigated the effects of FGD sludge on the pozzolanic reaction of reject-fly-ash-blended cement pastes. Many studies using CaSO4•2H2O typed FGD gypsum as cement retarder has been reported[2,8-12]. Howevere, few studies using FGDG as retarder were reported so far. In present study, the chemical compositon, phase composition, structure and features of CaSO3•0.5H2O typed FGD gypsum have been analyzed, and its application characters used as cement retarder have been investigated experimentally."

Jan 1, 2008

By J. M. Brupbacher, D. C. Nagle

"The XD TM * approach to producing metal matrix composites employs an in-situ precipitation technique for the formation of the reinforcement directly in the matrix of interest. Key features include: thermodynamically stable reinforcement; clean particle/matrix interfaces, single-crystal reinforcement; size, chemistry, and shape control; uniform distribution; compatibility with conventional ingot techniques; and grain refinement.Using XD~ technology it is possible to simultaneously introduce a number of different reinforcements in a given matrix, thus allowing for designing the microstructure to meet a specific material need. Thus, XD1l'1 technology is a very useful technique for achieving ""designer"" or ""engineered"" microstructures. XD TM technology has been applied to a number of systems including AI, NiAI, TiAI and Cu. Materials property and processing benefits will be discussed."

Jan 1, 1988

By Suk J. Im, I. S. Min, Daesoo Kim

UFP are defined by atoms or their clusters having diameter in the range of l0Å-0.l.um. Due to a ratio of very large surface area to volume, they have peculiar properties such as extra high surface energy. Recently UFP deposition technique may find its new applications to various areas such as conductive/resistive film formation. In this method, gas flow with UFP jet through the nozzle which is considered to be a free molecular flow is maintained at a very high speed (~100m/s). Using this technique, mixture film of Fe and Ni, and Ag/ Ag-Alloy etc. were obtained, and their mechanical and electro-magnetic properties were determined. The experimental results are pending. The test results and discussion will be presented in the main paper.

Jan 1, 1988

By Geir Wedde, Anders Sorhuus

"Vast quantities of energy are released as heat to the environment from industrial operations. Many countries target waste heat recovery to mitigate CO2 emission. Exhaust gases from industries such as primary aluminium smelting, carry a substantial portion of the waste heat generated. For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants. Heat exchange surface would be exposed to dust laden gases with risk of fouling. Heat exchangers of innovated design and operation have overcome the potential of excessive fouling rates. Heat exchangers of the ""shell and tube"" design have been demonstrated for exhaust gases from ferroalloy as well as primary aluminium smelters. In addition to the heat recovery, gas cooling results in smaller gas treatment plants with lower costs and reduced emission. The aluminium experience is exampled in the paper.IntroductionIndustrial usage of energy continues to grow as a result of increasing volumes of production, a trend that is likely to continue in the coming decades as living standards keep rising globally. World energy consumption (Figure la) is to grow 49 % by 2035 (ref. 2010) as reported by EIA [1]. The industrial sector consumes somewhat more than 50% of the total world energy consumption predominantly the energy increased demand comes from non-OECD countries in Asia. The industrial consumption by production of metals iron and steel accounts for 14 % and for non-ferrous metals 3 % mostly for aluminium production (Figure lb). Aluminium production will be discussed in this paper as an example of an industry with large quantities of waste heat to recover"

Jan 1, 2012

By Georgeta Rata, Cornelia Petroman, Ioan Petroman

"Proper training and education in the field of recycling and waste treatment are inconceivable without the proper teaching of the terminology specific to both recycling (aerospace products recycling, automotive recycling, general recycling, recycling behaviour, recycling schemes, recycling systems, and waste recycling) and waste (characterization of waste, electronic waste, heavy-metal containing waste, monitoring of waste, radioactive waste, solid waste, waste collection, waste conversion, waste recycling, waste reutilization, waste stabilization, waste storage, and waste treatment) in both the students’ mother tongue and in English for Special Purposes (ESP) as a second language (with focus on the structuring of the specific terminology). Including linguistic approaches among the possible approaches of environmental protection and material sustainability means including linguistics among the various disciplines addressing energy supply, cement and building materials, metallurgy, chemistry, glassware, pulp and paper industry, machinery, automobile and electronic industries, collection, and sorting, further treatment and final disposal of post-consumer material.IntroductionCultural and technical changes have produced more novel artefacts than novel activities or novel properties, generating new vocabulary needs that are readily answered by new words (nouns).The purpose of this research is to show that ‘waste words’ – phrasal words (items that have the internal structure of phrases but function syntactically as words, e.g., cattle waste) and particularly compound nouns (words formed by combining roots, that tend to have a meaning that is more or less idiosyncratic or unpredictable, e.g., wastepaper ‘discarded paper’) – used in the study of the English of recycling, waste treatment, and clean technologies can be misleading for both native and non-native students and/or users of English because their structure alone does not allow instant, proper understanding of their meaning.Our hypothesis is that this inconvenient can be overcome by getting to reach the proper meaning of these new words. Or, arriving at the precise meanings of the ‘waste words’ depends on our knowledge of the world (for example, wastepaper indicates that some used paper is discarded and not wasted) rather than on purely linguistic knowledge."

Jan 1, 2008

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001