Search Documents

By B. Nebreda, I. Vegas, R. Vigil, O. Rodríguez, M. I. Sánchez de Rojas, M. Frías, R. García, J. Urreta

"This paper shows the possibility of reutilize paper sludge waste as supplementary cementing material for the cement manufacture. This industrial waste consists essentially of a mixture of organic matter (30%) and inorganic compound, such as calcite and clay minerals. The raw paper sludge does not present pozzolanic properties, but once calcined at 650ºC during 2 hours, exhibits high pozzolanic activity, similar to silica fume at 28 days, as a consequence of the transformation of kaolinite into metakaolinite. Calcined paper sludge was used as partial Portland cement replacements of 0, 5, 10 and 20%. Enhancement in compressive strength was appreciably obtained for 10 and 20% substitution levels from 7 days on. Furthermore, calcined paper sludge slightly reduces the initial and final setting times of cement paste. Introduction Natural pozzolanic materials have been ordinary used in different aspects of construction, mainly for their influence on the microstructure and durability of blended cement matrixes [1, 2]. Due to the regulations of environmental protection, many researches are focusing on the possibility of obtaining pozzolanic materials from industrial wastes and not from natural materials (ceramic wastes, silica fume (SF), activated clays) [3–5]. One of the most used pozzolanic products is the metakaolin (MK) obtained from the activation of natural clay (kaolinite). The positive effect that MK has on blended cement performances [6,7] and also the influence that curing temperature and matrix nature have on the reaction kinetics and stability of hydrated phases produced during the pozzolanic reaction, according to the studies carried out by Frías et al. [8,9] are well known. However, there is a worldwide trend towards the use of recycled products in cement industry. In this line, some authors have reported an alternative way of obtaining MK from waste paper sludge [10-14]. The raw paper sludge (PS), once calcined under controlled conditions (700-800ºC), produces a MK with pozzolanic properties [15-20]. The present research is part of an experimental study about alternative source for MK from the Spanish paper recycling industry and its use as supplementary cementing material. This contribution pays special attention to the option of reducing activation temperature below 700ºC. This fact has a positive effect in reducing the energy consumption, as well as in reducing environmental impacts associated with decarbonation of calcite. The chemical and mineralogical characteristics of raw paper sludge and derived calcined product are described. In addition, the influence and behavior on blended cement properties (setting times and mechanical properties) are also discussed."

Jan 1, 2008

By M. A. Aziz

The electrochemical performance of a series of carbon materials produced from coconut shells, which are very cheap and readily available in Bangladesh was investigated for their viability as anode materials in rechargeable lithium-ion batteries. X-ray diffraction technique was used to measure the interlayer spacing (d002) of the produced carbon materials. A number of half-cells were prepared with the produced carbon materials from coconut shell as working electrode and metallic lithium as counter electrode with 1MLiPF6 electrolyte in a mixture of ethylene carbonate and dimethyl carbonate. The discharge-charge profiles were measured for the different half-cells by using Arbin 24-channel Cyler. The value of interlayer spacing of the coconut-based carbon material was found to be 0.397 nm at 900°C, which is most suitable for lithium-ion insertion into the carbon structure without any expansion. The specific discharge capacity of carbon material from coconut shell heat treated to 900°C was found to be 1015.65 mAh/g. The coconut carbon material heat treated to 900°C delivered 335.22 mAh/g reversible capacity, which is comparable to the commercial carbon/graphite presently used in lithium-ion battery systems. The irreversible capacity loss and coulombic efficiency in 25th cycle of half-cell made with coconut carbon material were found to be 0.16% and 99.83% respectively. The carbon material produced from coconut shell can, therefore, be used as a potential anode for rechargeable lithium-ion batteries.

Jan 1, 2006

By Chetan P. Malhotra

This paper describes an online control system and simulation environment for reheating furnaces. The system can be configured for implementing manual control as well as automatic control using either look-up tables or online model predictions. The simulator is also used for offline generation of optimized normal operation and delay setpoints for look-up tables and generating ideal heating curves for model-based control. Finally, it is employed to compare the performance of the above control strategies over a typical period of operation of a pusher-type reheating furnace. Keywords: Reheating furnace, control strategy, model-based control

Jan 1, 2003

By Xiyun Yang

Magnetite was prepared by hydrogen reduction method. For a conversion to cobalt-modified magnetite, magnetite particles were suspended into a solution containing Co2+ and Fe2+ to precipitate a cobalt ferrite layer on the surface. pH value influences the particle composition directly, the desirable CoFe2O4 is obtained when pH value is 12. The coercivity increases with the increase of cobalt content, cobalt efficiency reaches a maximum value at cobalt content of 2.71wt%. With cobalt modification, magnetite particles have similar lattice constant and squareness ratio to that without cobalt modification. TEM and XPS analyses indicate that acicular morphology is retained during the coating process, the epitaxial growth layer consists of CoFe2O4and 0.3Co2O3CoFe2O4 at cobalt content of 2.71wt% and 5.03wt%, respectively.

Jan 1, 2006

By T. V. Jayaraman, D. Das, B. Mallesham, A. R. James

The PNN-PZT xPb(Ni0.3Nb0.67)03-(1-x)Pb(Zr0.31 Ti0 69)03 (0.2=x=0.6) based relaxor-ferroelectric material was synthesized by colurnbite precursor (NiNb206) method via conventional solid state reaction. Homogeneous mixture of required oxides and precursor was calcined at 850°C for 4 hrs to obtain phase pure perovskite. Pellets of PNN-PZT ceramics were sintered at 1100oC for 4 hrs. Phase pure perovskite structure was confirmed by the X-ray diffraction analysis. From the X-ray diffraction analysis it is also confirmed that there is a structural transformation from the rhombohedral to tetragonal with increase in PZT content and existence of morphotrophic phase boundary (MPB) at x = 0.5 composition. The morphology and microstructure of the sintered pellets were observed using the scanning electron microscope. P-E loop measurement shows the high remnant polarization (19.12 µC/cm2) and low coercive field (6.89 kV/cm) at MPB compared to all other compositions. The electromechanical planar coupling coefficient (kp) was measured through the resonance and anti-resonance method using the LCR meter. The piezoelectric strain coefficient (d33) measured directly using the d33-meter. At x = 0.5 composition the highest value of d33 = 398 pC/N is obtained.

Jan 1, 2012

By Gordon Holcomb, George R. St. Pierre, Robert A. Rapp

Carbon/Carbon composites offer promise as high-temperature structural materials. A primary limitation on their application is the need to provide protection against oxidation in hot oxidizing environments. Silicon carbide conversion coatings have been shown to provide extended protection at temperatures of 1600°C. SiC coated C/C components have been used in several aerospace applications. In the present paper, the preparation of carbon fibers and their treatment during subsequent processing into coated components are discussed with particular emphasis on the processing variables that can result in improved oxidation resistance. In particular, the influence of substrate inhibitors and selective sealants for cracks in coated C/C components are analysed.

Jan 1, 1988

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003

By H. Kurama

In this paper, utilization of fly ash as a value added product in areas such as novel materials, waste management, fillers and agriculture is reviewed with the aim of helping the expand of the usage of fly ash and reduce the environmental and economic impacts of disposal. The used unburned carbon benefication/treatment methods such as low temperature combustion, froth flotation, partical size classification and electrostatic separations to remove unburned carbon particles from fly ash are also discussed.

Jan 1, 2006

By Anand Kumar, Pradeep kumar Jha, Suman Kant, Pradeep Kumar

"It has been a major challenge to reduce the intermixed grade formation during ladle change-over operation in continuous casting process of tundish steelmaking. The F-curve generated by step input of the tracer (new grade steel) tells about the intermixed grade amount for different grade specifications. Use of flow modifiers is beneficial in reducing the intermixed grade because of the change in slope (in different time zones) and position of the F-curve due to their placement at tundish bottom. Present study aims at investigating the role of dam placed before the outlet in a multi-strand tundish with reference to the slope behavior of F-curve in different time zones during the teeming operation plays an important role in determining the intermixed amount.Introduction In Continuous casting process, the old grade steel remaining in the tundish (reservoir between ladle and mould) from the old ladle gets mixed with new grade steel from new ladle and leads to intermixed grade which is considered to be of inferior quality. Although formation of intermixed grade is inevitable with the sequential method of casting, its amount can be controlled by changing the flow behavior of steel inside the steel. Intermixing in a slab caster tundish was simulated using 3-D numerical model based on k-å turbulence equation and compared their result with that of water model experiment Yeh and Hwang [1]. Huang and Thomas [2] reported that quantity of residual fluid in tundish affects the composition distribution in the transitional slab and thus the intermixed length. Huang and Thomas [3] developed three sub models to predict mixing in tundish, liquid core of strand and solidification. Thomas [4] developed a one dimensional model to simulate the final composition distributions in slab caster of continuous casting and investigated the effect of process variables on the intermixing. Alizadeh mehdi et al., [5] simulated of the intermixing phenomenon for slab casting for three different sub models. Goldschmidt et al. [6] developed a numerical model that predicted the location of the intermixed steel in a four line round caster. Lan and Khodadadi [7] studied for the transient fluid flow of liquid steel, heat transfer and solidification during the flying tundish change process. Cho and Kim [8] developed a mixing model to predict the outlet concentration of the tundish during grade transition. Most of the work reported in the literature has dealt with intermixing in slab caster tundish. Billet caster units are more often being used by steel industries due to growing demand of billets. The multiple outlets lead to varying degree of intermixing with time owing to their different distance (location) from the inlet. Use of flow modifier to minimize the intermixed amount, however has also not been discussed in detail so far. Further no work has been reported regarding effect of slope of F-curves obtained through different outlets on intermixing. Hence keeping these objectives in mind attempt has been made by authors to analyze the slope of Fcurves after dividing them into three different time zones and the effect of these time zones on intermixing."

Jan 1, 2012

By A. Dell’Era, M. Pasquali, C. Lupi

"An electrochemical cell has been designed to treat very diluted cobalt solutions, i.e. those deriving from recycling processes of lithium-ion batteries. A reticulated vitreous carbon sponge was used as cathode and a Pt-coated Ti net as anode. A controlled potential electrolysis has been carried out in a solution flowing in the cell and maintained at a constant pH of 6.5. Considering the cathode dimensions (10.0 cm * 10.0 cm * 1.25 cm), rather high volumes of solution (>1 litre) can be treated with flow rates up to 1.6 l/min. The process yield is obviously related to the solution concentration; it has been observed that, starting with a solution containing 200 ppm of Co2+, the yield is initially ~35-40%, but it decreases to ~20% when 80% of the initial cobalt content has been electrowon. The yield increases up to ~50% if the carbon electrode is coated by cobalt. The conditions allowing a fast and complete removal of cobalt are outlined. Introduction Industrial liquid effluents containing heavy metal ions arise not only during hydrometallurgical processing, but also in many sector of chemical industries utilizing metal catalysts and process reagents. These waste solutions containing low quantities of metallic ions can be treated by chemical precipitation, solvent extraction, ion exchange, etc. before final discharge. All these techniques could be efficient for complying the aqueous effluents with the severe rules related to the environmental impact, but they can not directly produce metals. Particularly the chemical precipitation presents two main drawbacks, huge amount of sludge prodction and reagent costs to produce this useless and sometime dangerous sludge that have to be considered. Electrochemical technologies can be used for the treatment of effluents polluted by metal ions, showing the following advantages in comparison with other processes: 1. recovering of the polluting substances in metallic forms, with subsequent reusing; 2. absence of process slag, which should be subsequently disposed of. In this work an electrochemical reactor with a reticulated vitreous carbon cathode and a platinated titanium net anode has been designed and utilized for removal Co from waste aqueous solutions. Porous materials have been used as electrodes for this cell, as their high specific surface area favours the treatment of these low metal content solutions (1-7). This kind of electrodic material presents very interesting chemical-physical characteristics such as: low density, low thermal expansion and high electrical and thermal conductivities; particularly the reticulated vitreous carbon (RVC) presents a very elevated void volume, rigid structure, good resistance to temperatures in non-oxidizing environments and very low resistance to fluid flow."

Jan 1, 2008

By M. Benavides

An experimental study is carried out With sulphide ore obtained from Bailadores-Venezuela as well as artificial concentrates. Concentrates of the minerals from froth flotation are fused to study equilibrium between the matte and slag phases. The first part of the work deals with obtaining a concentrate by flotation experiments with collective and selective reagents, with acceptable metallurgical recovery, studying the influence of different parameters in the process. The second part gives the results of the experimental investigation. on thermodynamic equilibrium in smelting which facilitates knowledge of the elemental processes, giving bases for the possibilities of reducing the loss of metal in slag.

Jan 1, 1983

By P. Sergi

A method of characterizing gold ores with respect to processing is proposed. The method includes microscopical examinations to obtain qualitative and quantitative data that relate to processing. The main thrust, however, involves laboratory heavy liquid separation tests, laboratory amalgamation tests, and laboratory cyanidation tests to determine the proportions of gold that can be recovered in a conventional processing operation. Two different Brazilian gold ores: a quartz vein gold ore, and gold in metasediments were tested.

Jan 1, 1989

By Ann M. Hagni

Reflected Light Microscopy (RLM) And Scanning Electron Microscopic-Energy Dispersive Spectroscopic Analysis (SEM-EDS) Study Of Electric Arc Furnace (EAF) Dusts Have Shown That Their Mineralogy Is Complex And Varied. The Particles Are Largely Spherical, And Can Be Seen In RLM Sections To Be Composed Of Franklinite, And Zincite, But They Show Significant Solid Solution With Each Other And May Contain Small Amounts Of Chromium. These Crystalline Phases Occur As Crystals And Skeletal Growths Within Ca-Fe-Si Glass. Because Chlorine Is A Deleterious Constituent In Recovered Zinc Products From EAF Dusts, Special Attention Has Been Given To Chlorine-Bearing Phases, And They Include Hydrophylite (Cacl2), Lime (Cao), And Organic Phases. Pyrohydrolysis-Treated EAF Dusts With Silica (Si02), Tungstite (W03), Alumina (A1203), And Bunsenite (Nio) Additives Contain Franklinite, Scheelite (Cawo4), Willemite (Zn2SiO4), And Hematite (Fe2O3)

Jan 1, 1992

By Paul Pajunen, Michael Sheedy

"Acid separation using short bed ion exchange is a now well established technology in copper refinery tankhouses. Refinery bleed streams from liberator cells are treated by short bed systems to produce an acid-free byproduct stream that contains the bleed metals and valuable nickel salts. Removing the acid eliminates the need for a black acid evaporator and reduces the amount of sodium carbonate required in nickel selective precipitation processes. The recovered sulfuric acid can be recycled to the tankhouse. This same technology is routinely used to treat other acids such as hydrochloric, nitric, and hydrofluoric. In the case of hydrochloric acid, the process can selectively separate chloro-anionic complexes such as Zn, Pb, and Cu, which are then eluted with water. The acid recovery technology can also be closely coupled with ion exchange processes in order to minimize regenerant acid consumption. In many hydrometallurgical applications resin regeneration often requires an acid dosage multiple times the stoichiometric minimum. Coupling an acid recovery bed with the IX column allows recovery and recycle of the free acid in the spent regenerant, thus reducing the overall acid consumption to just slightly more than stoichiometric.Short Bed Ion ExchangeThe short bed ion exchange process has been extensively used in the metal finishing industries since the early 1970s [1,2]. Short bed systems have also been sold to primary metals producers for the separation of sulfuric acid from copper refinery bleed streams [3] and for the recovery of nickel and cobalt from plant effluent streams. This unique technology optimizes the ion exchange process and offers a number of significant advantages over conventional ion exchange. The principal features and benefits of this technology are presented below."

Jan 1, 2012

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Nan Zhang, Gai-feng Xue, Shangchao Liu, Benquan Fu

"The high-magnetization microspheres of Fe3O4 encapsulated with S1O2 and T1O2 layers (Fe3O4@SiO2@TiO2) were prepared. The microspheres were characterized by transmission electron microscopy and scanning electron microscopy. These high-magnetization microspheres could be readily dispersed by shaking whereas they could be rapidly separated from the aqueous solution simply by applying an external magnetic field. The two shells of S1O2 and T1O2 protected the iron oxide well and the microspheres were stable in acid and base solutions. Therefore, they have a good potential for the enrichment of phosphopeptides or photocatalytic activity. They could also be used to remove metal ions from waste water.IntroductionSolid-phase extraction (SPE) is the most commonly used separation technique for its simplicity, consumption of small volumes of organic solvent, and the ability to achieve a higher enrichment factor. The quest for new adsorbents is an important factor in improving analytical sensitivity and precision in SPE techniques. To date, many novel adsorbents, such as nanometer-sized materials, carbon nanotubes, mesoporous materials and magnetic nanoparticles have been employed in SPE.Magnetic polymeric microspheres, an interesting advanced composite material, have received increasing attention in the past few decades because of their unique physical and chemical properties and their potential for use in applications in various fields [1]. Magnetic microspheres consisting of an iron oxide core and a silica shell have attracted particular attention for their unique magnetic response, low cytotoxicity, and chemically modifiable surface. The core-shell magnetic silica microspheres have shown great potential in the fields of biotechnology and biomedicine for applications such as cell labeling and separation, enzyme and protein separations, targeted drug delivery, and magnetic ferrofluids hyperthermia."

Jan 1, 2012

By Marshall Khan

The Goodfellow Expert Furnace System Optimization Process (Goodfellow EFSOP?) is a proprietary process that uses real-time and continuous off-gas analysis, along with process monitoring to optimize the operation of electric arc furnaces (EAF) for steelmaking. With the exception of off-gas composition, dynamic process measurements within the EAF are not possible due to the harsh operating environment. The Goodfellow EFSOP? system provides a dynamic indication of the operating conditions within the EAF. Continuous measurement of furnace off-gas composition, along with other furnace operating parameters is used to elucidate the fate of chemical energy usage within the EAF including: the evolution of carbon from the molten steel bath; the in-leakage of air into the furnace; the extent of combustion above the molten steel bath and the occurrence of dangerous water-leaks from the furnace cooling system. The ability to measure the process reliably and continuously enables Techint Goodfellow Technologies Inc (TGTI) to implement dynamic process control of combustion within the electric arc furnace and to optimize the overall operation through adjustments to the EAF process based on off-gas measurement. This paper discusses the methodology and results achieved from several recent Goodfellow EFSOP? installations in South East Asia.

Jan 1, 2006

By O. A. Bascur

Applying the latest information technologies in mining and metallurgical complexes has become a serious challenge to management and technical teams. Emerging component design is changing the way the user relates to the desktop. Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. The integration of information from mining, mineral processing and metallurgical performance monitoring increases production efficiency, even when many elements cannot be measured directly. Three case studies of large mining/metallurgical complexes are highlighted.

Jan 1, 1999