Search Documents

By Chu Yong Cheng

Synergists can be used in solvent extraction to improve the selectivity of extractants for metals. Research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy / CSIRO Minerals has shown that the pH isotherm of nickel with Versatic 10 was significantly lowered by the addition of the synergist Acorga CLX50. The paper discusses how this synergistic shift can be used to alleviate a gypsum formation problem at Bulong nickel laterite operation in Western Australia. Metal pH isotherms were obtained with Versatic 10 and synergist CLX50 using synthetic leach solutions. In terms of pH50, the extraction order of the metals with 0.5 M Versatic 10 alone was Cu > Zn > Ni > Co > Mn > Ca > Mg, whilst the extraction order with Versatic 10 and 20% by volume CLX50 was Cu > Ni Zn > Co > Mn > Ca > Mg with the pH50 (Mn-Co) significantlyincreased. This is significant because the isotherms of valuable metals Ni, Cu, Co and Zn shift more towards low pH than those of the waste metals Mn, Mg and Ca, resulting in a possible good separation of Ni, Cu, Co and Zn from Mn, Mg and Ca. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel plants make these processes complicated and costly in capital and operation. The research work carried by the SX groupat the AJ Parker Centre has led to the development of direct SX (DSX) processes to recover nickel and cobalt from leach solutions using synergistic organic systems. Semi-continuous tests with a BHP Billiton pilot plant leach solution showed that Ni and Co together with Zn and Cu were separated from the major impurities, Mn, Mg, Ca, and Cl, in the first SX circuit. The co-extracted impurities were easily scrubbed. After stripping, Ni and Co together with Zn and Cu were concentrated, resulting in a much smaller second SX circuit in the down stream processes.

Jan 1, 2003

By Dieter Wanner

Off-gas cleaning from metallurgical? plants, requires in many cases very low dust contents which are, difficult to achieve with conventional scrubbers, even with high energy input. Lurgi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to the scrubbing zone,, An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag granulation after a waelz kiln achieving less than l mg/m3 in the clean gas.

Jan 1, 1992

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By S. R. Reddy

Thennodynamic properties of several quaternary systems are calculated using our recently modified Margules equations. The modified Margules equations are expressed up to infinite order in the vicinity of solvent. Quaternary system of one solvent and three,solute partials are derived. First order interaction coefficients of binary, ternary and cross -interaction parameters of quaternary system are used to'evaluate the partial functions. In the original fonn of Margules equations,derived partial functions are convergent and same 'as Unified ,Interaction Parameter Fonnalism. But considering up to infinite order of the Margules coefficients, the functions are divergent, in order to overcome this restriction, Margules equations are modified to get consistent equations. Derived partial functions are thennodynamica Hy consistent with Maxwell and Gibbs Duhem relations. The derived logarithmic activity coefficient of the solvent and solutes are consistent with the ternary systems. The calculated data, ie., activity coefficient values of nitrogen and interaction coefficients are in good agreement with the data of Fe-Cr-V -N. Fe-Ni-V -N, Fe-Cr-Ta-N and Fe-Ni-Ta-N systems.

Jan 1, 1999

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By C. E. Dodson

Conventionally hydrometallurgical recovery processes from sulphide concentrates include roasting, leaching, precipitation, impurity removal and zinc electrowinning. The use of the novel (yet commercially proven in other mineral and metallurgical industries) TORBED process reactor for the flash roasting of sulphides will be proposed. The potential advantages in its application will be discussed including very fine particle processing capability, lower cost smaller roasters, waste minimization, improved leaching efficiency and overall process simplification.

Jan 1, 1999

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro, Thiago Samarão Motta

This work has as its objective to characterize ceramic bodies formulated with ornamental rock waste and two different clays to produce ceramic paver. Specimens were made by uniaxial press-molding at 20 MPa and then fired at 950 and 1050oC respectively. The determined technological properties were: plasticity, dry bulk density, linear shrinkage, water absorption and flexural rupture strength. The results showed that the type of the clay has strong influence on the properties of interest for heavy clay ceramics. The investigated waste must be incorporated in small amounts to avoid increasing in the porosity of the ceramics.

Jan 1, 2015

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By Jun Chang, Jin-hui Peng, Jing Chen, Li-bo Zhang

The leaching of indium from refractory zinc oxide flue dust(ZOFD) is attempted to utilize microwave sulfating roasting process, followed by water leaching. The ZOFD and roasted product were characterized by XRD and SEM/EDS analysis. The effects of various roasting parameters, such as roasting temperature/duration, the proportion of sulfuric acid, as well as the leaching parameters such as the leaching duration and liquid/solid ratio, were assessed. The results indicate that nearly 97% of indium could be leached under the following conditions: mass ratio of concentrated sulfuric acid to ZOFD to be 0.5, roasting temperature of 150 ℃ and duration of 1.5 hours; while the optimal leaching conditions hold at temperature of 25 ℃ for 1 hour, with 4:1 of liquid/solid ratio. The indium leaching rate by the microwave roasting increased by 8% as compared with the conventional roasting process under identical conditions.

Jan 1, 2015

By Clara María Lamus Molina

The following minerals found in the residual black sands from gold mining in El Bagre Antioquia (Colombia) were identified as having major economic interest: Ilmenite (FeTiO3), with an average of 49% of TiO2, frequently altered presenting crowns; lamellaes of rutile and alteration textures; titanomagnetite with up to 25% of TiO2; magnetite (Fe3O4) in individual grains or associated with others minerals as hematite and ferromagnesian silicates rutile (TiO2) with considerable quantities of Nb2O5(0.1-3.7%Wt); zircon (ZrSiO4) with 66%Wt of ZrO2 and monazite with an average of 63.43%Wt of REE, this frequently associated to xenotime and thorite forming textures as little drops. Analysis in EPMA and SEM/EDS showed percentages of minor elements and traces, thereby clearly establishing the applications of these minerals in diverse industries. Furthermore, a detailed granumetric study of the different minerals and textural relationships among them also allowed for establishing the basis for possible processing and exploitation.

Jan 1, 2006

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015