Search Documents

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Martin Fischer

A new method for the quantitative image analysis of complex microstructures in steel is presented. Microstructures in modern steel grades on the one hand become more and more complex while on the other hand the size of the constituents is scaled down ever further. For these reasons it is increasingly difficult or even impossible to access reliable quantitative information on ratios, shapes and spatial distributions of individual phases and constituents by utilising traditional metallographic analysis methods. The presented new analysis approach is object-based. Its basic processing units are so-called ?image objects? which reflect the pictured structures by merged groups of likely related pixels. By the use of image objects, information on shape, graphical texture and spatial distribution of the microstructural constituents can be processed. With these additional data available, it is possible to quantitatively analyse complex microstructures. This is demonstrated by the application of the method to SEM images of different multiphase steel grades. Because the analysis routine is fully automated, the analysis of large amounts of image data is possible and thereby the investigation of statistically relevant areas of microstructures.

Jan 1, 2009

By Chris P. Pistorius

Over the past few decades the carbon intensity of ironmaking and steelmaking has been reduced considerably through improved efficiency in blast furnace ironmaking, partial replacement of coke with less carbon-intensive fuels, and increased use of scrap and direct-reduced iron in steelmaking. To evaluate possible further reductions in carbon intensity accurate process information is needed. A preliminary test of the fidelity of publicly reported data as a source of process information is reported here. The sources are industry roundups of electric furnace furnace steelmaking and blast furnace ironmaking (published by the Association for Iron and Steelmaking Technology), and data recorded by the Environmental Protection Agency under the US Greenhouse Gas Reporting Program. From a comparison for an integrated steelmaking plant and an electric furnace furnace plant, it appears that the values from the two data sources are consistent. The comparison does rely on process details such as the quantitative relationship between injected oxygen and carbon emissions in electric furnace steelmaking.

By Federica Paglietti

In this work is presented SEX (Structural & Elemental X-Ray Instrument), the first spectrometer completely portable which make non-destructive X-ray fluorescence and diffraction analysis, in contemporary and in real time. This instrument has been realized using miniaturized detectors, the same model installed on the mission Pathfinder NASA, and X-ray microtubes. SEX allows the chemical and mineplogical characterization of all kind of solid materials and allows to make chemical stratigraphy and liquids analysis.

Jan 1, 1998

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total 'heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By P. M. Tait, N. A. Warner

"The refining of thermally produced zinc is currently performed using a highly energy intensive and arguably outmoded process, distilling zinc under atmospheric pressure at temperatures of 900°C to 1000°C. In order to produce refined zinc more profitably and with less environmental impact a new process has been proposed. This process is generic to all thermal zinc smelters and aims to match the purity of zinc from current technology (99.99%-99.999%). The objective is to perform all separation processes using only the heat contained in the smelter product stream. Vacuum conditions are extensively used lowering operating temperatures and enhancing separations. As part of this process zinc is distilled under vacuum from high concentration obtaining a refined product with respect to lead content. A mathematical model has been developed from fundamental principles to describe this stage, the distillation of zinc across a temperature difference between two circulating zinc streams in open channels under vacuum. Heat for the distillation is supplied by the liquid phase, necessitating a large recycle to maintain high operating temperatures, and keep zinc concentrations high. In determining this model and the operating conditions required, relationships between temperature, pressure and composition are considered.IntroductionCurrent technology (the Refluxer) used to refine thermally produced zinc is both expensive and highly inefficient. At present 80% of the worlds zinc is produced via the electrolytic process reflecting the poorer performance of the thermal route, the zinc-lead blast furnace and Refluxer. A new process is proposed to overcome the drawbacks of current processes. These drawbacks are both economic and environmental. The Refluxer requires 6.6 GJ of energy to refine one tonne of SHG zinc 1, other disadvantages of the Refluxer stem from high operating temperature, around 900°C, and liquid zinc being highly corrosive towards ferrous metals. The Refluxer is constructed from silicon carbide sections which join together by means of flat machined faces making liquid metal leaks inevitable. The Refluxer columns are very sensitive to thermal cycling, thermal shock and mechanical vibration, which easily lead to structural failure. To avoid thermal stress on the columns the feed rate and feed temperature need to be kept constant which means the feed baths to the columns must be able to accept solid and liquid feed as the Refluxer has to operate when the smelter is shut down."

Jan 1, 1998

By Pedro A. Netto, Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Frederico M. Margem, Gabriel O. Glória

Since environmental issues are becoming more and more important Worldwide. Nowadays, Natural fibers are been used to substitute the synthetic ones. Although PALF fiber is an important natural fiber and its mechanical Properties surpass in various aspects some other lignocelluloses fibers, such few studies have been conducted with the fiber obtained from leaf of PALF plant. In order to better evaluate the mechanical properties and possible applications, this paper aims to improve the elastic modulus of the PALF fiber by Weibull statistics, by evaluating their mechanicals properties and possible applications. The fibers were divided in diameter intervals and the tensile strength and elasticity modulus were measured in each range. The fractured surface was examined using scanning electron microscopy. The results, interpreted by the Weibull statistical method, showed a correlation between the fiber elastic modulus and its diameter.

Jan 1, 2015

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and l200°C, positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation where negative deviations were observed.

Jan 1, 2003

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By Junzo Hino

Most of the waste that contains a small portion of copper is landfilled. The recycling process of copper from the waste, such as shredder residue, should be developed in order to save mineral resources and prevent environmental pollution. Shredder residue, generated from disposed automobiles and electric appliances, consists of many types of plastics, glasses and metals. The combustion heat of plastics is efficiently used for smelting in the recycling process that consists of melting and reduction. Because the waste contains numerous components the knowledge of the distribution behaviors of the main components is necessary to develop the recycling process. The distribution behaviors in the recycling process are evaluated by using the thermodynamic calculation program, HSC Chemistry. The calculation results are compared with the practical operation data of the recycling process and discussed.

Jan 1, 2003

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By Corby G. Anderson

Hydrometallurgical technology for the pretreatment of refractory gold concentrates has been developed at Sunshine Mining and Refining Company. It employs a patented nitrous-sulfuric acid pressure leaching process which' was proven industrially at the Sunshine refinery. Additionally, pretreatment for removal of antimony and some other impurities is done with alkaline sulfide leaching. This paper will discuss the successful application of these two technologies for pretreatment of a refractory gold concentrate prior to CIL gold recovery. A complex gold concentrate composed of pyrite, arsenopyrite and stibnite was tested. Results of antimony leaching in alkaline sulfide media will be discussed including some details of a novel and selective recovery method for gold leached by polysulfide or thiosulfate" Also, the factors important in and the results of the application of nitrogen species catalyzed pressure leaching to refractory gold concentrates will be detailed.

Jan 1, 1996

By Heimo Thalhammer

During the refining of lead, copper or other metals the furnaces used in the process · often produce waste gases. This paper illustrates how these waste gases can be successfully treated and destroyed by CTP 2-bed or multi-bed compact systems, modified for the additional reduction of dioxins and furans. The CTP regenerative thermal oxidizer also destroys voes (organic compounds and odours) using ceramic blocks as a heat exchanging media. The raw gas is forced through the ceramic beds where it is heated up to the oxidation temperature level. The voes, dioxins and furans are destroyed in the combustion chamber, subsequently generating water, eo2 and heat. The hot purified gas heats up a second ceramic bed, which is used to preheat the raw gas after the valves have been switched. This process does not produce any secondary waste such as contaminated water, polluted air or any other products that have to be disposed of.

Jan 1, 2000

By Yuan Zeping

This paper describes the distribution and removal of the main impurities in the pyrometallurgical process ?at the Guixi Smelter. The paper discusses in detail our converting schedule?of3S-SB and injecting deeply a mixture ofNa2CO) and CaO flux into the converters to enhance impurity removal.

Jan 1, 1998

By M. del C. Ruiz

The extraction of Nb and Ta from a columbo-tantalite of San Luis, Argentina, is being studied by using a pressure reactor and HF as leaching agent. The reagents and products have been characterized by several techniques such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), X-ray fluorescence (XRF), X-ray difracction (XRD), surface area (BET) and size particle analysis. Experimental results have shown that the extraction of niobium and tantalum increases with increasing temperature, reaction time and acid concentration. For particle size between +80 and -355 mesh no significant changes are detected. It is also slightly affected by the stimng speed. XRD analysis of the residues did not show formation of new crystalline structures.

Jan 1, 1999