Search Documents

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By Shilai Yuan, Huimin Lu, Panpan Wang

A big andalusite ore bed was found in Dingxi District, Gansu, China. In this paper, the feasibility of producing solar grade silicon from aluminum-silicon alloys by carbothermal reduction of andalusite ore was studied. First, the carbothermal reduction experiments were conducted in a 100 kVA DC submerged arc furnace with reducing temperature 2000–2200 °C and reducing time 4 h, the hypereutectic aluminum-silicon alloys containing 50–55 mass% aluminum and 35–45 mass% silicon were obtained; then the investigation on solidification of the hypereutectic Al-Si melts under the temperature gradient as an intensified separation silicon way was carried out. According to previous investigation, the optimized technical process for solar grade silicon and eutectic Al-Si alloy from andalusite ore was proposed.

Mar 1, 2017

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By Mojtaba Ahmadiantehrani

A previous study showed that up to 80% gold extraction could be obtained with 160 lbs/ton hypochlorite consumption at ambient temperature from a low grade Carlin-type carbonaceous ore. Crushing the ore to a finer size and agglomerating with cement decreases hypochlorite consumption by 60%; while, agglomeration and curing the cement-ore mixture with hypochlorite solution has no significant effect on total gold extraction. The high hypochlorite consumption is due to oxygen depletion as the solution percolates through the column, i.e., oxidation of gangue materials. These side reactions are reduced at sub-ambient temperatures resulting in a substantial further decrease in hypochlorite consumption. The optimum temperature range and additional reduction of hypochlorite consumption by introducing the reagent into the column at different elevations will be discussed.

Jan 1, 1992

By Natasa Mitevska

The statistical analysis of the slag composition influence on copper losses to discard slag in the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Yugoslavia) is presented in this paper. The model for the slag basicity calculation is determined, and connected to the copper distribution coefficients between the matte and slag phase. The influence of all components on the slag structure is also illustrated.

Jan 1, 2003

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By Martin E. Nelson

Several heavy metal separation techniques are currently being developed for soil remediation at various Department of Defense and Department of Energy (DOE) Facilities. The majority of these techniques involve a wet process using water, PH modifiers or other compounds. The United States Naval Academy (USNA) has developed a dry process for heavy metal separation. The process uses air classification technology to concentrate the metal contaminant into a fraction of the soil. The advantages of this dry process are that it creates no contaminated by product and uses commercially available technology. The USNA process is based on using a Gayco-Reliance air classifier. Tests have been conducted with the system at the Naval Academy and the University of Nevada-Reno (UNR). The USNA tests used soil from the Nevada Test Site mixed with bismuth at a concentration of 500-1000 ppm. The UNR tests used soil from four DOE sites mixed with uranium oxides and plutonium at an activity level of 100-700 pCi per gram. Concentration of activities and volume reduction percentages are presented for the various soils and contaminants tested.

Jan 1, 1995

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By Versiane Albis Leão

This work aims at the selection of an appropriate eluant for cyanide recycling using ion exchange resins. Based on a literature review as well as on experimental results, the elution of resins loaded with copper and minor amounts of iron and nickel is discussed. The resins Imac HP 555s, Amberlite IRA 900 (Rohm&Hass) and Purolite A860S (Purolite Co) were eluted using either NaCI, zinc and nickel cyanides, hydrochloric acid, sulfuric acid or acid thiourea solutions. The results indicate that saline solutions are effective only with polyacrylic resins (Purolite A860S), failing to desorb the metals, specially the nickel cyanocomplex, loaded on polystyrene-based resins. Cyanide solutions of both zinc and nickel are capable of eluting over 90% of the loaded metals. In contact with pure acid' solutions, iron precipitates onto the resin beads, as Cu(II) ferrous cyanideCu2Fe(CN)6.xH20. Thiourea is able to elute all the three metal cyanocomplexes owing to the increased solubility of copper cyanocomplexes in the presence of this complexing agent. The results demonstrate that a universal eluant is not available and the selection of the most appropriate resin-elution procedure should be based on the specific features of the system under consideration

Jan 1, 1998

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting. lime roasting. is being tested for retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04). oldhamite (CaS). calcium sulfite (CaS03). hematite (Fe2O:J), magnetite (Fe304). and minor amounts of pyrrhotite (Fe1.xS) and pyrite. At 600°C. 650°C and 700°C. the main constituents are anhydrite. oldhamite. and hematite. At 750°C. 800°C. and 850°C. anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides. calcium sulfite. hematite. and minor oldhamite. magnetite. and pyrrhotite. At 650°C. 700°C, 750°C. and 800°C, anhydrite, oldhamite. arsenic sulfides, and hematite are present. At 850°C. the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CIM) in the determination of the calcium-sulfur-oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RIM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1991

By S. Yabe

The reinforcement of the annual copper production capacity to 330,000 metric tons has been attained at Saganoseki Smelter & Refinery in 1991, which is one of the largest and most efficient custom smelters in the world. Many operational improvements and technology developments have realized the increase of smelting and refining capacity without adding main facilities to the existing process. The blister copper refining and anode casting process is composed of two 400 tonnes anode furnaces and one double-wheeled casting machine with the capacity of 80 tonnes per hour. The great innovations in this process such as the finding of essential issue on the extending of anode-mould life and the development of a new anode-mould casting machine have raised the operation efficiency by 14% Now, the process is producing 38,500 tonnes per month of best quality anode in well- controlled working condition, and anode productivity per worker increased by 52%. The progress in extending anode-mould life, the mechanism of the new anode-mould casting machine and the increase of efficiency in butane reduction, that were the principal parts of many technological improvements, are described in the present paper, including some operation results.

Jan 1, 1993

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By John W. Pickens

The recycling of industrial wastes and by-products is an important component of ecologically responsible industrial management. Converting waste streams into value-added products or material and energy resources with a profit margin assures the continued viability and practice of recycling. The recycling of aluminum stands out as one of the best examples with major economic and environmental benefit. However, the benefits are compromised by landfilling of black dross and salt cake, waste streams produced from within the recycling process itself. This paper reviews Alumitech's strategy and progress in establishing a tertiary aluminum industry based on closed-loop recycling of black dross/saltcake; one which does not compete with the primary and secondary aluminum industries, but rather serves their needs to ensure the continued economic benefits of aluminum recycling and elimination of environmental liablJity associated with landfilling of black dross/saltcake. Alumitech has made significant progress toward that goal in operation of its new recycling facilities in Cleveland where recovered aluminum and nonmetallic residue from salt based drosses is being converted into commercial products, eliminating the landfilling of the greatest portion of dross/saltcake. The economic strategy for recycling saltcake and its progressive achievement is reviewed.

Jan 1, 2000

By Jianhua Xin, Min Chen, Jin Xu, Hui Li, Nan Wang, Ming Chen

The kinetics study of blast furnace dust (BFD) recycling with flash reduction process at high temperature has been carried out using a high temperature drop tube furnace in laboratory scale. A combination characterization methods of chemical titration and SEM-EDS were used to track the reduction kinetics. The experiments using CO and CO2 mixtures with range of CO/CO2 (1:0, 1:1) at different temperature (1623–1723 K) and at different reduction time (1560– 2340 ms) were conducted. It was found that the reduction degree increases with the increase of temperature and reduction time as well as CO concentration. The carbon contained in the original BFD has weak in fluence on the reduction potential in the form of gasification. The unreacted core model was adopted based on the observation of the cross section and the measurement of iron element content, the effective diffusion coef ficient and reaction rate constant were determined and the rate controlling step was also analyzed.

Mar 1, 2018

By Long Meng, Yaodong Yi, Kuiyuan Chen, Zhancheng Guo, Yu Li

Blast furnace slag is the main by-product discharged in the iron and steel industry and contains considerable waste heat at dischargeing temperature between 1450 and 1550 °C. To fully utilize waste heat and slag, this study directly converted high temperature liquid Ti-bearing blast furnace slag into glass-ceramics via the “Petrurgic” method. Samples at different crystallization temperature were prepared and its influence on crystal phases, pore structure, and compressive strength were investigated via SEM, XRD techniques, and compressive strength measurements. Results showed that all glass-ceramic samples contained main crystals of perovskite, diopside and gehlenite and had a qualified mechanical performance with compressive strength above 100 Mpa, which meets the requirement of Chinese national standard for natural granite stone. With increasing crystallization temperature, pore size decreased, while the size of the perovskite phase firstly decreased and then increased with decreasing crystallization temperature. Samples had an optimum crystallization temperature of 1215 °C, maximum grain size and a densified structure with minimal pore defect.

Mar 1, 2018

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999