Search Documents

By J. A. Rowland

Magnesium alloys containing nickel, nickel and manganese, lithium, lithium and manganese, and lithium and aluminum were investigated. Melting, casting, and mechanical working techniques and the heat treatment of various compositions were studied. Amenability to cold and hot working was shown for many compositions. The magnesium-nickel and magnesium-nickel-manganese alloys failed to develop superior mechanical properties and were very low in resistance to corrosion. The magnesium-lithium series, although entirely plastic, had low strength properties. The addition of small amounts of aluminum to the Mg-Li base did not affect greatly either the ductility or the strength; further additions developed increased strength, but only at room temperature, and the alloys became brittle with age. Continued study, concentrating on the ductile lithium-rich beta phase as a base composition for ternary and quaternary systems, is recommended.

Jan 1, 1956

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By J. E. Shelton

Flotation tests are described on samples of two lowgrade nickeliferous ores of Oregon and Washington. The sample from the Congress mine, Ferry County, Wash., contained 1.2 percent Ni, occurring chiefly as millerite. The sample from the Shamrock mine, Jackson County, Oreg., contained 2.20 percent Ni and 0.78 percent Cu occurring chiefly as pentlandite, nickeliferous pyrrhotite, and chalcopyrite. The millerite in the Congress ore was concentrated by flotatioin with aulfydric collectors in a series of locked tests to recover 73 percent of the nickel as a 7 percent bulk concentrate. By successively regrinding and floating the bulk concentrate, it was further concentrated to 12.4 percent Ni at a recovery of 59 percent and 21.8 percent Ni at a recovery of 50 percent. Attempts at selective concentration of the copper-nickel Shamrock ore were only partly successful because of the intimate association of pentlandite and chalcopyrite. The nickel concentrate, which contained 86 percent of the nickel, had an analysis of 4.42 percent Ni and 1.03 percent Cu. The copper concentrate had an analysis of 18.8 percent Cu and 1.96 percent Ni and contained 48.5 percent of the copper. A bulk sulfide concentrate contained 92 percent of the copper and 01 per¬cent of the nickel and had an analysis of 4.17 percent Ni and 1.63 percent Cu.

Jan 1, 1956

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By D. E. Wolfson

As part of its overall program of coal-carbonization research, the Bureau of Mines is studying the coking properties of coals from various fields of this country. Few of the coals included in this survey are used for the manufacture of metallurgical coke, although some well-known coking coals necessarily are tested to provide comparative data, particularly on blending properties. The overall objectives of the study were given in detail in a previous report.3/ The inherent suitability of coal for metallurgical purposes, as distinguished from economic considerations, depends primarily on (1) the available reserves, (2) chemical composition, (3) preparation characteristics, and (4) carbonization behavior. These items are considered in selecting coal for carbonization tests.

Jan 1, 1956

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By J. S. Browning

The purpose of this Bureau of Mines project was to develop a method for recovering kyanite and sillimanite from the present zircon-mill tailing of the Jacksonville and Starke, Fla., plants of Humphreys Gold Corp. The kyanite and sillimanite in the ore are not being exploited at present, but procedures for recovering the two minerals were worked out by the Bureau in the interest of conserving natural resources. The current zircon-mill tailing of the Starke plant contains up to 20 percent of a mixture of kyanite and sillimanite. A similar product of the Jacksonville plant contains up to 15 percent kyanite and sillimanite. The average annual production of the tailing now being stockpiled contains several thousand tons of the two minerals. Laboratory batch-flotation tests were made on the materials to determine the feasibility of flotation methods for recovering high-grade concentrates. Various reagents were employed under different conditions to determine the optimum conditions for flotation of kyanite and sillimanite and retardation of the gangue materials. The results of the preliminary flotation tests were encouraging enough to warrant more comprehensive testing of a larger sample of the ore in the laboratory pilot plant.

Jan 1, 1956

By J. R. Ruark

Because of the importance of oil-shale reserves the Bureau or Mines resumed research investigations in this field beginning in 1944. The Bureau early decided to build a Large-scale demonstration plant to accomplish the dual purpose of obtaining design data and to produce crude shale oil for refining studies. Two 40-ton-Capacity batch N-T-U (Nevada-Texas-Utah) retorts were completed for this purpose in 1947. After a preliminary operation, the plant was used to investigate process variables of air rate, recycle gas rate, and shale particle size and crude. Correlations obtained from these variables are presented in this report. Researchers concluded that recycle gas was not necessary for efficient operation of the process. Short comings of the batch method of processing the oil shale are pointed out in the report. Several periods of prolonged production operations were carried out. During these periods, the retorts were operated to produce as much crude oil per day as possible. The lifetime operation of the N-T-U retorts was divides into three periods, namely, preliminary operation, process variable study, and production operation. During the preliminary operation, 187 runs were made with a total of 7,596 tons of raw shale used to produce 3,688 barrels of crude shale oil. During the process variable study, 179 runs were made with a consumption of 7,494 tons of raw shale and a production of 4,218 barrels of crude shale oil. The production operation consisted of 554 runs in which 22,457 tons of raw shale was used to produce 12,359 barrels of crude shale ail. The overall total for the lifetime operation of the retorts consisted of 920 runs with a total consumption of 37,547 tons of raw shale and a production if 20,265 barrels of crude shale oil.

Jan 1, 1956

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956